3M Lava Scan ST with Steinbichler dongle -questions-

D

drstranger

Member
Full Member
Hi,
I have bought a used 2009 Lava ST scanner with a Steinbichler dongle.
From reading the forum, i have understood that i need a special PC that has a usb 2.0 controller card and a firewire card.
I want to run it with exocad, so where do i get the driver from, when i have the Steinbichler dongle?
What other things do I need to get it running?
Does anyone know where I can get the calibration block from?
I have purchased the scanner in Germany and I have to send it to Australia, what measurements have to be taken to send the scanner safely with air freight?

Thanks :)
 
doug

doug

Well-Known Member
Full Member
Maybe Jensen can help. The package I bought from them has the Steinbichler scanner. Call their tech support.
 
cnhart@me.com

[email protected]

Active Member
Full Member
Hi,
I have bought a used 2009 Lava ST scanner with a Steinbichler dongle.
From reading the forum, i have understood that i need a special PC that has a usb 2.0 controller card and a firewire card.
I want to run it with exocad, so where do i get the driver from, when i have the Steinbichler dongle?
What other things do I need to get it running?
Does anyone know where I can get the calibration block from?
I have purchased the scanner in Germany and I have to send it to Australia, what measurements have to be taken to send the scanner safely with air freight?

Thanks :)
Pm me, I'm in melbourne and have one
 
OP
D

drstranger

Member
Full Member
Hi.
I can't send a PM though, probably because I have a new profile.
Can you please send me a PM?

Thanks
 
O

Oleh_77

New Member
Hello everyone,
I have bought a used Steinbichler Scan ST I scanner.
what software I should use to work with the scanner and then what software I should use to connect my scanner to exocad?
is a Opticat for this case?
 
2thm8kr

2thm8kr

Beanosavedmysociallife
Full Member
Hello everyone,
I have bought a used Steinbichler Scan ST I scanner.
what software I should use to work with the scanner and then what software I should use to connect my scanner to exocad?
is a Opticat for this case?
You will need a special license/dongle to use with exocad. An exocad reseller should be able to help you with this plus the free exoscan module to operate the scanner.
 
O

Oleh_77

New Member
Tnx, a lot!!!
the free exoscan module to operate the scanner --- It`s part of exocad or from another free sofrware like DentaScan?
 
2thm8kr

2thm8kr

Beanosavedmysociallife
Full Member
A module of exocad. Integrates with a lot of other scanners as well.
 
O

Oleh_77

New Member
Do I need to use any other (additional) software from the manufacturer of scanner "Steinbichler Scan ST I" for example the driver or other?
"Optocat" is already installed on my PC and I have no idea is it for this scanner or not.
thank you in advance!
 
A

andy700

New Member
where can i get the drivers for lava st?
can anyone show me the dongle in the photo?
 
user name

user name

Well-Known Member
Donator
Full Member
Do I need to use any other (additional) software from the manufacturer of scanner "Steinbichler Scan ST I" for example the driver or other?
"Optocat" is already installed on my PC and I have no idea is it for this scanner or not.
thank you in advance!
where can i get the drivers for lava st?
can anyone show me the dongle in the photo?
Contact the milling center in Richmond Virginia. He has everything you need for these.
 
Guest Room
Help Users
  • No one is chatting at the moment.
  • Chat Bot:
    Room has been pruned!
    Chat Bot: Room has been pruned!
    Top Bottom