Milling Machine

[Toto]

Looking for a Milling Machine - not for a CadCam setup - the other type with a handpiece connected for implant abutments. Do they have to cost so much?
Any ideas - keep watching at Zirodent for a secondhand one .

 

[sidesh0wb0b]

Looking for a Milling Machine - not for a CadCam setup - the other type with a handpiece connected for implant abutments. Do they have to cost so much?
Any ideas - keep watching at Zirodent for a secondhand one .

ebay has had a few recently.....for half the cost of new

 

[ksmksam]

where are you from i have one iam from jordan

 

[Digitaldentist]

Hi Toto,

Just out of curiosity..

What kind of machine are you looking for ? 4 axis..5 axis ?

Stepper or Servo ?

What would you like to cut with it...Wax and PMMA only ? Zirconia too ? What about Chrome or Titanium ?

Is a dry system ok or would you need it to be wet ?

Tell me a little more about your needs.....when you decide what you want to do.. then tell

me what price you would be willing to pay for it....

Let's talk about it...

Let's hear what the community has to say on the subject

What capabilities would you like to see included that you don't see anyone offering now

Your post implies that you feel that the price of a new machine is just too high...

what price would you consider to be fair....

What are we all looking for...... and why ?

Thanks,

- Mike

 

[Sevan P]

Hi Toto,

Just out of curiosity..

What kind of machine are you looking for ? 4 axis..5 axis ?

Stepper or Servo ?

What would you like to cut with it...Wax and PMMA only ? Zirconia too ? What about Chrome or Titanium ?

Is a dry system ok or would you need it to be wet ?

Tell me a little more about your needs.....when you decide what you want to do.. then tell

me what price you would be willing to pay for it....

Let's talk about it...

Let's hear what the community has to say on the subject

What capabilities would you like to see included that you don't see anyone offering now

Your post implies that you feel that the price of a new machine is just too high...

what price would you consider to be fair....

What are we all looking for...... and why ?

Thanks,

- Mike

Mike he is asking about the air driven or electrical manual milling machine, the ones where you setup the arch on a table so when you start milling the abutments you waxed up or stock abutments they are all parallel to each other allowing a perfect draw. Basically the old school milling machine pre cerec and nobel scanners.

I found this site, they look ok not sure though.

Crown & Bridge

We have one that is 40yrs old, I can find out the manufacturer and see if they still make them or used ones on the net some where.

one more on amazon

Amazon.com: DENTAL MILLING MACHINE MX-7 AIR: Health & Personal Care

Actually that was made by the people in the first link.

The one we have is air driven, with a regulator to control speed, uses HP burs, the thing rips!!!

Sevan

 

[stumpf]

You can check the german ebay site too it's much better than any sites

Sonstige | eBay

But you can find also small german sec.hand shops like:

RM-Dental GmbH

MC-Dental Aktionen deutsch

Hope it helps

 

[Toto]

Mike he is asking about the air driven or electrical manual milling machine, the ones where you setup the arch on a table so when you start milling the abutments you waxed up or stock abutments they are all parallel to each other allowing a perfect draw. Basically the old school milling machine pre cerec and nobel scanners

Thats right Thanks Sevan P

Thanks to everyone for the info

 

[Sevan P]

You can check the german ebay site too it's much better than any sites

Sonstige | eBay

But you can find also small german sec.hand shops like:

RM-Dental GmbH

MC-Dental Aktionen deutsch

Hope it helps

Stumpf has a point, our is a german one and it is pretty solid. Have a look at see what comes up.

 

[rlhhds]

I have a Degussa F-1 that I have had for many years and no longer use.