For Sale Retiring, Lab equipment for sale

  • Thread starter Thread starter Car 54
  • Start date Start date
Car 54

Car 54

Well-Known Member
Donator
Full Member
Messages
8,246
Reaction score
1,122
Hello, after 45 years it's time to call it a career. All of the prices include shipping, so keep that in mind ;) :)

All payments are to be made by a banks Cashiers check, if I know you from experience on this forum a business check is okay, or by PayPal.


*Dry Mill and Programill suction price reduced by $1,500. to $14,000.
First off, a Programill Dry Mill with RFID reader, suction unit and PC. It will also include 2 new filters for the Programill suction unit, a new collet and some new tools for the mill, and a medium small airline dryer right next to the mill. I also had a bigger air line dryer right after the compressor's twin airline dryers so it's been taken care of in that way. I will deliver it in my Honda CRV within the states of MN, N.D., S.D., Iowa, Wisconsin and help set it up, and go over some tips to get you started. Otherwise, it will be shipped by a bigger shipping carrier. This unit was one of the first or 2nd units sold in the US, so there was no maintenance plan, service plan that I had to buy. BUT, you need to call your rep to find out what you would need to do if you wanted a yearly service contract, and if they would let you buy repair service as needed, ala carte or not, as my situation (new item for Ivoclar) was so new to them, they didn't know what to do, regarding a service contract.. I bought the mill on June 29th, 2021.

The Programill suction unit is this one (link). I can PM you a photo of it, as I ran out of images I was allowed to post in this thread. Again, it will come with 2 new filters, the Pre filter, and the HEPA filter. https://www.ivoclar.com/en_li/products/digital-equipment/programill-suction-unit

I'm a one man lab, so it wasn't heavy duty use, but normal use. I did also split some things up with the Mini Mill (milling wax). The CAM version is the Advanced CAM 4.4.13.0. The CNC is v7.08.00.P3. One of the main reason I bought it, let alone to be able to mill in house, is that I could use the compressor I already had, compared to needing to upgrade that for a Programill PM5. Asking price $14,000. Spindle hours are shown on the last image. It is the original spindle, it has never needed calibration and is built like a tank.

20250110_095740.jpg 20250110_095745.jpg 20250110_095815.jpg 20250110_104046.jpg Screenshot 2025-01-10 100327.jpg

2-S1 Sinter furnaces. One is a bit older, but I recently replaced the 2 front elements, and will include a new 2 tier Dostro tray. It has 8,474 firing hours and 62,619 operating hours. I'm asking $4,000. which includes shipping in the original box. The other one is newer, and will have the single tray. It has 5687 firing hours and 45,577 operating hours. I'm asking $4,500. which includes shipping in the original box. Both will include the calibration tool. Both are on v6.01
20250103_051753.jpg 20250103_051741.jpg


I'm at my image posting limit, so if you are interested in any of the following, I can PM you some images, otherwise I'll start another thread in 2 weeks (forum rules) but I also have...
  • Painful Pleasures complete anodizing kit with color chart $135. includes shipping. Sale pending.
  • emax press ingots are $90. per 5 piece tube, and $70. per 4 piece tube. Includes shipping. Full tubes of emax press=s MT's A3. LT's BL1 and BL4. HT's (work great for posterior monolithic) BL4, A2, A3 (2 tubes), C1, C2./ Tubes with 4 ingots for 70. each =s LT BL3, LT B1, LT B2, LT D2, HT A3.5, HT C1, MT A1. They need to be orders of 2 or more to help offset the free shipping.
I have a Pre programed Canon G16 camera with diffuser for patient photos, color correct monitor for viewing those photos, new electric straight handpiece, lab pans, etc. :)

More equipment can be found here:

CHeers :)
 
Last edited:
Hello, after 45 years it's time to call it a career. All of the prices include shipping, so keep that in mind ;) :)
Also, there is a lot of newer equipment for sale that can seem a little pricy, but I'm offering it at approximate 35-50% off, again including shipping. But you can also make me an offer. Some of the lesser priced item are shown towards the end.
All payments are to be made by a banks Cashiers check, or by PayPal.

First off, a Programill Dry Mill with RFID reader, suction unit and PC. It will also include 2 new filters for the Programill suction unit, a new collet and some new tools for the mill, and a medium small airline dryer right next to the mill. I also had a bigger air line dryer right after the compressor's twin airline dryers so it's been taken care of in that way. I will deliver it in my Honda CRV within the states of MN, N.D., S.D., Iowa, Wisconsin and help set it up, and go over some tips to get you started. Otherwise, it will be shipped by a bigger shipping carrier. This unit was one of the first or 2nd units sold in the US, so there was no maintenance plan, service plan that I had to buy. BUT, you need to call your rep to find out what you would need to do if you wanted a yearly service contract, and if they would let you buy repair service as needed, ala carte or not, as my situation (new item for Ivoclar) was so new to them, they didn't know what to do, regarding a service contract.. I bought the mill on June 29th, 2021.

I'm a one man lab, so it wasn't heavy duty use, but normal use. I did also split some things up with the Mini Mill (milling wax). The CAM version is the Advanced CAM 4.4.13.0. The CNC is v7.08.00.P3. One of the main reason I bought it, let alone to be able to mill in house, is that I could use the compressor I already had, compared to needing to upgrade that for a Programill PM5. Asking price $15,500. Spindle hours are shown on the last image. It is the original spindle, it has never needed calibration and is built like a tank.

View attachment 45704 View attachment 45705 View attachment 45706 View attachment 45707 View attachment 45708

Next:
2-S1 Sinter furnaces. One is a bit older, but I recently replaced the 2 front elements, and will include a new 2 tier Dostro tray. It has 8,474 firing hours and 62,619 operating hours. I'm asking $4,750 which includes shipping in the original box. The other one is newer, and will have the single tray. It has 5687 firing hours and 45,577 operating hours. I'm asking $5,000. which includes shipping in the original box. Both will include the calibration tool. Both are on v6.01
View attachment 45710 View attachment 45711

An Ivoclar P3010 G2 v7.3 Press and firing oven. It was purchased in March of 2024. It has 9 firing and vacuum hours on it, and 70 operating hours. It's essentially brand new. It will include the vacuum pump that came with it, also along with a new box of Microstar 13 mm disposable plungers (minus one). Asking $7,000. shipping and vacuum pump that came with it included, shipped in the original box. Brand new they go for $11,500 and I don't even know if that includes shipping and taxes?

View attachment 45712

Ivoclar P310 G2 porc. oven. 16325 operating hours, firing hours 819, vacuum hours 9. Price includes the vacuum pump that came with it, as well as shipping. Asking $3,000.
View attachment 45713
Dekama Austromat 3001. Lots of hours..LOL, but it does fire very nicely. When I run the first program after it's been shut off, it will chirp when it hits high temp, and its hold time for that cycle. After that, all the programs run normally. Incudes the original manual. Asking $1500. Includes original pump and shipping.
View attachment 45714

I'm at my image posting limit, so if you are interested in any of the following, I can PM you some images, otherwise I'll start another thread in 2 weeks (forum rules) but I also have...
  • Whipmix Power mixer with stand, and 4 mixing bowls, including a large one. ( a couple of them need a gasket) for $550.00 includes shipping.
  • 2 burn out ovens, one Jelrus PDQ, and a Ney 2-90 Series 2, $500. each includes shipping.
  • A year old Quatro Jet Stream Basic suction unit with 3 new bags, tubes, and foot peddle controller $425. includes shipping.
  • A Red Wing lathe with the quick release chuck and splash pan. $525. includes shipping.
  • 3 Articulators, 2 Hanau Modular and one B2M Quick Master (lightweight Denar type of articulator) The all have the main Denar magnetic plates, to receive the Denar magnetic mounting plates. One of the Hanau's will come with the occlusal jig, as well as the facebow jig (to receive and mount Denar facebows) @175.00 and the others @125.00 each, includes shipping.
Like I mentioned, I will have another thread regarding a Mini Mill, Quatro suction unit, 3Shape E1 scanner, 3Shape dongle includes abutment designer and model builder paid through June 1st, 2025, Vaniman dust collector, 2 accumulators, InSync and MiYO stain kits, Harvest Dental stain tray, pre programed camera for patient photos, color correct monitor for viewing those photos, e.max Ceram, Light cure box for Opti glaze, new electric straight handpiece, newer NSK Presto 2 HS handpiece, lab pans, ...etc etc :)

Like I say, feel free to PM me as far as anything listed that you may be interested in, before waiting for 2 more weeks :)

CHeers :)
Beer
Congrats on the retirement. I’m jealous! So what are you going to do to keep busy?
 
Wow! You're all done with the lab business!?!?! Amazing and awesome and how would it be? Hope it's for good reasons obviously
 
Beer
Congrats on the retirement. I’m jealous! So what are you going to do to keep busy?
Dawn my blue vest and greet you when you walk in the door...LOL. I'm not sure yet, but I will do something part time to keep busy and for a little extra spending cash :) Thank you for asking :)
 
Last edited:
Wow! You're all done with the lab business!?!?! Amazing and awesome and how would it be? Hope it's for good reasons obviously
For good reasons....maybe. All in all I was in burn out mode, and my last BIG account retired the end of December, and my other previous big account about 2 years ago. I could never make up for that loss of income, and the other offices tend to be bigger and send elsewhere.

I also found out last month that my other good account, is now doing chairside 25 minute zirconia posteriors along with the rest of the Sirona chairside he was doing. Essentially what I was getting were the tuff implant cases and intense single central cases. I lost my ambition and motivation to try and keep this going, especially alone.

And thank you for asking :)
 
Last edited:
For good reasons....maybe. All in all I was in burn out mode, and my last BIG account retired the end of December, and my other previous big account about 2 years ago. I could never make up for that loss of income, and the other offices tend to be bigger and send elsewhere.

I also found out last month that my other good account, is now doing chairside 25 minute zirconia posteriors along with the rest of the Sirona chairside he was doing. Essentially what I was getting were the tuff implant cases and intense single central cases. I lost my ambition and motivation to try and keep this going, especially alone.

And thank you for asking :)
Well, you got live through all the major changes of the field which is pretty cool. Too bad you won’t be around for the final death knell!
 
Well, you got live through all the major changes of the field which is pretty cool. Too bad you won’t be around for the final death knell!
🤣🤣🤣 Yep, I'd like to avoid that one :)
 
Thank you for your invaluable input, knowledge - your so enthusiastic responding to DLNW, keep replicating that as you move forward in life - cheers
 
Thank you for your invaluable input, knowledge - your so enthusiastic responding to DLNW, keep replicating that as you move forward in life - cheers
Thank you for the kind words, Snapper, I appreciate it. And all the best to you, too :)
 
Last edited:
Wow! Party

And I am jealous! 😬

Good luck in your next adventures! I will have a closer look at one or two of your 'leftovers' ...

I guess you could still contribute to the board, now that you have a bunch of free time!

See you around!
 
Congratulations! I like that you're going out healthy.
Thank you, friend :) Yes, I agree, but I'll probably know more about where I was at as I catch my breath and get more of my life back :)
See you at McDonalds next Monday at 7:00 AM 😅
 
Hello, after 45 years it's time to call it a career. All of the prices include shipping, so keep that in mind ;) :)
Also, there is a lot of newer equipment for sale that can seem a little pricy, but I'm offering it at approximate 35-50% off, again including shipping. But you can also make me an offer. Some of the lesser priced item are shown towards the end.
All payments are to be made by a banks Cashiers check, or by PayPal.

First off, a Programill Dry Mill with RFID reader, suction unit and PC. It will also include 2 new filters for the Programill suction unit, a new collet and some new tools for the mill, and a medium small airline dryer right next to the mill. I also had a bigger air line dryer right after the compressor's twin airline dryers so it's been taken care of in that way. I will deliver it in my Honda CRV within the states of MN, N.D., S.D., Iowa, Wisconsin and help set it up, and go over some tips to get you started. Otherwise, it will be shipped by a bigger shipping carrier. This unit was one of the first or 2nd units sold in the US, so there was no maintenance plan, service plan that I had to buy. BUT, you need to call your rep to find out what you would need to do if you wanted a yearly service contract, and if they would let you buy repair service as needed, ala carte or not, as my situation (new item for Ivoclar) was so new to them, they didn't know what to do, regarding a service contract.. I bought the mill on June 29th, 2021.

I'm a one man lab, so it wasn't heavy duty use, but normal use. I did also split some things up with the Mini Mill (milling wax). The CAM version is the Advanced CAM 4.4.13.0. The CNC is v7.08.00.P3. One of the main reason I bought it, let alone to be able to mill in house, is that I could use the compressor I already had, compared to needing to upgrade that for a Programill PM5. Asking price $15,500. Spindle hours are shown on the last image. It is the original spindle, it has never needed calibration and is built like a tank.

View attachment 45704 View attachment 45705 View attachment 45706 View attachment 45707 View attachment 45708

Next:
2-S1 Sinter furnaces. One is a bit older, but I recently replaced the 2 front elements, and will include a new 2 tier Dostro tray. It has 8,474 firing hours and 62,619 operating hours. I'm asking $4,750 which includes shipping in the original box. The other one is newer, and will have the single tray. It has 5687 firing hours and 45,577 operating hours. I'm asking $5,000. which includes shipping in the original box. Both will include the calibration tool. Both are on v6.01
View attachment 45710 View attachment 45711

An Ivoclar P3010 G2 v7.3 Press and firing oven. It was purchased in March of 2024. It has 9 firing and vacuum hours on it, and 70 operating hours. It's essentially brand new. It will include the vacuum pump that came with it, also along with a new box of Microstar 13 mm disposable plungers (minus one). Asking $7,000. shipping and vacuum pump that came with it included, shipped in the original box. Brand new they go for $11,500 and I don't even know if that includes shipping and taxes?

View attachment 45712

Ivoclar P310 G2 porc. oven. 16325 operating hours, firing hours 819, vacuum hours 9. Price includes the vacuum pump that came with it, as well as shipping. Asking $3,000.
View attachment 45713
Dekama Austromat 3001. Lots of hours..LOL, but it does fire very nicely. When I run the first program after it's been shut off, it will chirp when it hits high temp, and its hold time for that cycle. After that, all the programs run normally. Incudes the original manual. Asking $1500. Includes original pump and shipping.
View attachment 45714

I'm at my image posting limit, so if you are interested in any of the following, I can PM you some images, otherwise I'll start another thread in 2 weeks (forum rules) but I also have...
  • Whipmix Power mixer with stand, and 4 mixing bowls, including a large one. ( a couple of them need a gasket) for $550.00 includes shipping.
  • 2 burn out ovens, one Jelrus PDQ, and a Ney 2-90 Series 2, $500. each includes shipping.
  • A year old Quatro Jet Stream Basic suction unit with 3 new bags, tubes, and foot peddle controller $450. includes shipping.
  • A Red Wing lathe with the quick release chuck and splash pan. $525. includes shipping.
  • 3 Articulators, 2 Hanau Modular and one B2M Quick Master (lightweight Denar type of articulator) The all have the main Denar magnetic plates, to receive the Denar magnetic mounting plates. One of the Hanau's will come with the occlusal jig, as well as the facebow jig (to receive and mount Denar facebows) @175.00 and the others @125.00 each, includes shipping.
Like I mentioned, I will have another thread regarding a Mini Mill, Quatro suction unit, 3Shape E1 scanner, 3Shape dongle includes abutment designer and model builder paid through June 1st, 2025, Vaniman dust collector, 2 accumulators, Painful Pleasures Anodizing kit (with color chart), InSync and MiYO stain kits, Harvest Dental stain tray, pre programed camera for patient photos, color correct monitor for viewing those photos, e.max Ceram, Light cure box for Opti glaze, new electric straight handpiece, newer NSK Presto 2 HS handpiece, lab pans, ...etc etc :)

Like I say, feel free to PM me as far as anything listed that you may be interested in, before waiting for 2 more weeks :)

CHeers :)
hello there , i am intersted about your milling machine thanks
 
Hello, after 45 years it's time to call it a career. All of the prices include shipping, so keep that in mind ;) :)
Also, there is a lot of newer equipment for sale that can seem a little pricy, but I'm offering it at approximate 35-50% off, again including shipping. But you can also make me an offer. Some of the lesser priced item are shown towards the end.
All payments are to be made by a banks Cashiers check, or by PayPal.

First off, a Programill Dry Mill with RFID reader, suction unit and PC. It will also include 2 new filters for the Programill suction unit, a new collet and some new tools for the mill, and a medium small airline dryer right next to the mill. I also had a bigger air line dryer right after the compressor's twin airline dryers so it's been taken care of in that way. I will deliver it in my Honda CRV within the states of MN, N.D., S.D., Iowa, Wisconsin and help set it up, and go over some tips to get you started. Otherwise, it will be shipped by a bigger shipping carrier. This unit was one of the first or 2nd units sold in the US, so there was no maintenance plan, service plan that I had to buy. BUT, you need to call your rep to find out what you would need to do if you wanted a yearly service contract, and if they would let you buy repair service as needed, ala carte or not, as my situation (new item for Ivoclar) was so new to them, they didn't know what to do, regarding a service contract.. I bought the mill on June 29th, 2021.

I'm a one man lab, so it wasn't heavy duty use, but normal use. I did also split some things up with the Mini Mill (milling wax). The CAM version is the Advanced CAM 4.4.13.0. The CNC is v7.08.00.P3. One of the main reason I bought it, let alone to be able to mill in house, is that I could use the compressor I already had, compared to needing to upgrade that for a Programill PM5. Asking price $15,500. Spindle hours are shown on the last image. It is the original spindle, it has never needed calibration and is built like a tank.

View attachment 45704 View attachment 45705 View attachment 45706 View attachment 45707 View attachment 45708

Next:
2-S1 Sinter furnaces. One is a bit older, but I recently replaced the 2 front elements, and will include a new 2 tier Dostro tray. It has 8,474 firing hours and 62,619 operating hours. I'm asking $4,750 which includes shipping in the original box. The other one is newer, and will have the single tray. It has 5687 firing hours and 45,577 operating hours. I'm asking $5,000. which includes shipping in the original box. Both will include the calibration tool. Both are on v6.01
View attachment 45710 View attachment 45711

An Ivoclar P3010 G2 v7.3 Press and firing oven. It was purchased in March of 2024. It has 9 firing and vacuum hours on it, and 70 operating hours. It's essentially brand new. It will include the vacuum pump that came with it, also along with a new box of Microstar 13 mm disposable plungers (minus one). Asking $7,000. shipping and vacuum pump that came with it included, shipped in the original box. Brand new they go for $11,500 and I don't even know if that includes shipping and taxes?

View attachment 45712

Ivoclar P310 G2 porc. oven. 16325 operating hours, firing hours 819, vacuum hours 9. Price includes the vacuum pump that came with it, as well as shipping. Asking $3,000.
View attachment 45713
Dekama Austromat 3001. Lots of hours..LOL, but it does fire very nicely. When I run the first program after it's been shut off, it will chirp when it hits high temp, and its hold time for that cycle. After that, all the programs run normally. Incudes the original manual. Asking $1500. Includes original pump and shipping.
View attachment 45714

I'm at my image posting limit, so if you are interested in any of the following, I can PM you some images, otherwise I'll start another thread in 2 weeks (forum rules) but I also have...
  • Whipmix Power mixer with stand, and 4 mixing bowls, including a large one. ( a couple of them need a gasket) for $550.00 includes shipping.
  • 2 burn out ovens, one Jelrus PDQ, and a Ney 2-90 Series 2, $500. each includes shipping.
  • A year old Quatro Jet Stream Basic suction unit with 3 new bags, tubes, and foot peddle controller $450. includes shipping.
  • A Red Wing lathe with the quick release chuck and splash pan. $525. includes shipping.
  • 3 Articulators, 2 Hanau Modular and one B2M Quick Master (lightweight Denar type of articulator) The all have the main Denar magnetic plates, to receive the Denar magnetic mounting plates. One of the Hanau's will come with the occlusal jig, as well as the facebow jig (to receive and mount Denar facebows) @175.00 and the others @125.00 each, includes shipping.
Like I mentioned, I will have another thread regarding a Mini Mill, Quatro suction unit, 3Shape E1 scanner, 3Shape dongle includes abutment designer and model builder paid through June 1st, 2025, Vaniman dust collector, 2 accumulators, Painful Pleasures Anodizing kit (with color chart), InSync and MiYO stain kits, Harvest Dental stain tray, pre programed camera for patient photos, color correct monitor for viewing those photos, e.max Ceram, Light cure box for Opti glaze, new electric straight handpiece, newer NSK Presto 2 HS handpiece, lab pans, ...etc etc :)

Like I say, feel free to PM me as far as anything listed that you may be interested in, before waiting for 2 more weeks :)

CHeers :)
Congrats brother! From a one-man-lab to another, Stay healthy and enjoy the new journey!!
 
Wow! Party

And I am jealous! 😬

Good luck in your next adventures! I will have a closer look at one or two of your 'leftovers' ...

I guess you could still contribute to the board, now that you have a bunch of free time!

See you around!
Thank you for the the kind words and the celebration emoji :)
 
Congrats on your retirement! Hope you have a hobby to pursuit ... just don't let boredom take over. Cheers
 
Top Bottom