DP3000 error

rh3000 · Jun 7, 2013

Slipstream said:
I have seen faulty solenoid issues - the machine does release the cleaning station smoothly - if you help the release and it is happy that is the issue - but almost always the encoder strip is the problem

Thanks for your response. I cleaned the strip, but unfortunately I am getting the same error. (Fatal Error followed by HMS Error Recovery). Any other thoughts?

See the log below... Appreciated.

Fri 06/07/13 12:20:39 DEBUG BTN_PRESSED 11 Yes Pressed
Fri 06/07/13 12:20:39 Exiting Application - Log Stopped
Fri 06/07/13 12:20:40 DEBUG PARAM_CHANGE 0 Change Modeler Type: ProJet SD
Fri 06/07/13 12:20:40 DEBUG PARAM_CHANGE 0 LoadBuildStyle: STANDARD FRACTAL
Fri 06/07/13 12:20:40 Log Started - ProJet SD 3000 1.06 Nov 21 2008 09:01:42
Fri 06/07/13 12:20:43 DEBUG PARAM_CHANGE 0 Change Modeler Type: ProJet SD
Fri 06/07/13 12:20:43 DEBUG PARAM_CHANGE 0 LoadBuildStyle: STANDARD FRACTAL
Fri 06/07/13 12:20:44 DEBUG NOTICE 0 Computer: PROJET_41018
Fri 06/07/13 12:20:44 DEBUG MACHINE_INI 0 Creation Time: 11/16/09 18:42:56
Fri 06/07/13 12:20:44 DEBUG MACHINE_INI 0 Last Modify Time: 06/07/13 12:19:10
Fri 06/07/13 12:20:44 DEBUG MACHINE_INI 0 Machine Hours: 28471.24
Fri 06/07/13 12:20:44 DEBUG MACHINE_INI 0 Build Hours : 879.89
Fri 06/07/13 12:20:44 DEBUG MACHINE_INI 0 Lamp Hours : 164.00
Fri 06/07/13 12:20:44 DEBUG MACHINE_INI 0 Part Cartridges: 68
Fri 06/07/13 12:20:44 DEBUG MACHINE_INI 0 Support Cartridges: 144
Fri 06/07/13 12:20:44 DEBUG NOTICE 0 FPGA Combined Signature: 12
Fri 06/07/13 12:20:46 DEBUG NOTICE 0 Material Control Type 2 board initialization version numbers:RFID: 021; Part: 023; Support 023
Fri 06/07/13 12:20:46 DEBUG NOTICE 0 Clamp Feed System found installed **********************
Fri 06/07/13 12:20:46 DEBUG NOTICE 0 Hi Res mode: 1
Fri 06/07/13 12:20:46 DEBUG NORMALIZATION 5 Waveform: 5
Fri 06/07/13 12:20:46 DEBUG NORMALIZATION 1 Support Group 1: 1
Fri 06/07/13 12:20:46 DEBUG NORMALIZATION 2 Support Group 2: 2
Fri 06/07/13 12:20:46 DEBUG NORMALIZATION 1 Support Group 3: 1
Fri 06/07/13 12:20:46 DEBUG NORMALIZATION 2 Support Group 4: 2
Fri 06/07/13 12:20:46 DEBUG NORMALIZATION 1 Support Group 5: 1
Fri 06/07/13 12:20:46 DEBUG NORMALIZATION 2 Support Group 6: 2
Fri 06/07/13 12:20:46 DEBUG NORMALIZATION 0 Support Group 7: 0
Fri 06/07/13 12:20:46 DEBUG NORMALIZATION 1 Part Group 1: 1
Fri 06/07/13 12:20:46 DEBUG NORMALIZATION 1 Part Group 2: 1
Fri 06/07/13 12:20:46 DEBUG NORMALIZATION 1 Part Group 3: 1
Fri 06/07/13 12:20:46 DEBUG NORMALIZATION 2 Part Group 4: 2
Fri 06/07/13 12:20:46 DEBUG NORMALIZATION 1 Part Group 5: 1
Fri 06/07/13 12:20:46 DEBUG NORMALIZATION 1 Part Group 6: 1
Fri 06/07/13 12:20:46 DEBUG NORMALIZATION 0 Part Group 7: 0
Fri 06/07/13 12:20:47 DEBUG NOTICE 0 Send Parameters To DSP
Fri 06/07/13 12:20:47 SUP_IDX MS_INITIALIZE 0 Initialize D&K Support Feed System
Fri 06/07/13 12:20:47 PRT_IDX MS_INITIALIZE 0 Initialize D&K Part Feed System
Fri 06/07/13 12:20:47 DEBUG TEMP_STATE_CHANGE 4 Adapter Build
Fri 06/07/13 12:20:47 HMS WIPE_INACTIVE 0
Fri 06/07/13 12:20:47 HMS_RCVR RECOVERY_INACTIVE 0
Fri 06/07/13 12:20:47 PREP IDLE 0
Fri 06/07/13 12:20:47 DSP LOG 0 Comm Channel Opened
Fri 06/07/13 12:20:47 DSP LOG 0 SetResolutionMode : 1
Fri 06/07/13 12:20:47 DSP LOG 0 Entering Main Command Loop
Fri 06/07/13 12:20:47 DEBUG NOTICE 0 RmtDiag Listen

ing on 192.168.10.207 port 22376
Fri 06/07/13 12:20:47 DSP LOG 0 Servo Disabled by PC
Fri 06/07/13 12:20:47 DSP LOG 0 SetResolutionMode : 1
Fri 06/07/13 12:20:47 DSP LOG 0 Init Supp Indexer to 0.000000
Fri 06/07/13 12:20:47 DSP LOG 0 Init Part Indexer to 0.000000
Fri 06/07/13 12:20:47 DEBUG NOTICE 0 Listen

ing on 192.168.10.207 port 22375
Fri 06/07/13 12:20:47 DSP LOG 0 Init Supp Plunger to 1.176999
Fri 06/07/13 12:20:47 DSP LOG 0 Init Part Plunger to 0.152000
Fri 06/07/13 12:20:47 DEBUG NOTICE 0 UDP Socket on 192.168.10.207 port 22377
Fri 06/07/13 12:20:47 DEBUG NOTICE 0 Diag2 Listen

ing on 0.0.0.0 port 1039
Fri 06/07/13 12:20:47 DEBUG NOTICE 0 Security Listen

ing on 192.168.10.207 port 22378
Fri 06/07/13 12:20:47 DEBUG NOTICE 0 UDP Security Socket on 192.168.10.207 port 22378
Fri 06/07/13 12:20:47 SUP_IDX IDLE 0 Cartridges and plunger found in feed positions
Fri 06/07/13 12:20:48 PRT_IDX IDLE 0 Cartridges and plunger found in feed positions
Fri 06/07/13 12:20:48 DEBUG TEMP_STATE_CHANGE 4 Adapter Build
Fri 06/07/13 12:20:48 DSP LOCAL_LOG 0 Found 3 Support cartridges. From 012
Fri 06/07/13 12:20:48 DSP LOCAL_LOG 0 Found 3 Part cartridges. From 012
Fri 06/07/13 12:20:48 DSP LOCAL_LOG 0 Realtime GO_TO_BUILD
Fri 06/07/13 12:20:48 DSP LOCAL_LOG 0 Machine Off Time Sets Delay
Fri 06/07/13 12:20:48 DSP LOCAL_LOG 0 Jetstack Delay = 10 Minutes
Fri 06/07/13 12:20:54 DEBUG NOTICE 0 MQG Bypass Enabled
Fri 06/07/13 12:20:54 SUPPORT CHANGE_CARTRIDGE 0
Fri 06/07/13 12:20:54 PART CHANGE_CARTRIDGE 0
Fri 06/07/13 12:20:54 DEBUG PARAM_CHANGE 0 LoadBuildStyle: SD FRACTAL
Fri 06/07/13 12:20:55 BUILD INITIALIZATION 0
Fri 06/07/13 12:20:55 BUILD WAIT_READY 0
Fri 06/07/13 12:20:55 BUILD PRE_JOB_CHECKS 0
Fri 06/07/13 12:20:57 DEBUG NOTICE 0 Send Parameters To DSP
Fri 06/07/13 12:21:52 DSP LOCAL_LOG 0 Maintenance Temp Over Temperature
Fri 06/07/13 12:31:00 DEBUG BTN_PRESSED 11 Yes Pressed
Fri 06/07/13 12:31:11 DIAG USER_VALIDATED 0 RmtDiag: User ProJet_RH logged on from machine 192.168.10.207 port 1046
Fri 06/07/13 12:33:25 DEBUG TEMP_STATE_CHANGE 5 Reservoir Build
Fri 06/07/13 12:36:04 DEBUG TEMP_STATE_CHANGE 6 Jetstack Delay; Delay: 10
Fri 06/07/13 12:46:04 DEBUG TEMP_STATE_CHANGE 7 Control Build; Delay: 10
Fri 06/07/13 12:46:33 DEBUG TEMP_STATE_CHANGE 7 Control Build; Delay: 10
Fri 06/07/13 12:46:33 DSP LOCAL_LOG 0 Realtime READY_TO_BUILD
Fri 06/07/13 12:46:33 DSP LOG 0 Servo Enabled by PC
Fri 06/07/13 12:46:34 BUILD HMS_ERROR_RECOVERY 0
Fri 06/07/13 12:46:34 HMS_RCVR RECOVERY_BEGIN 0
Fri 06/07/13 12:46:34 HMS_RCVR RECOVERY_MOVE_ZX 0 ServiceHmsRecovery Error State = 4
Fri 06/07/13 12:46:34 DSP LOCAL_LOG 0 ServiceHmsRecovery Error State = 4; Move Z
Fri 06/07/13 12:46:54 HMS_RCVR RECOVERY_MOVE_XZ 0
Fri 06/07/13 12:46:54 DSP LOCAL_LOG 0 ServiceHmsRecovery Error State = 4; Home X
Fri 06/07/13 12:46:54 DSP LOG 0 Home X Back
Fri 06/07/13 12:46:55 HMS_RCVR RECOVERY_DISENGAGE_SOLENOID 0
Fri 06/07/13 12:46:57 HMS_RCVR RECOVERY_CHECK_SOLENOID_DISENGAGED 0
Fri 06/07/13 12:46:57 DSP LOG 0 Home X Back
Fri 06/07/13 12:46:58 HMS_RCVR RECOVERY_CHECK_SOLENOID_2 0
Fri 06/07/13 12:46:58 HMS_RCVR RECOVERY_CHECK_SOLENOID_DISENGAGED 0
Fri 06/07/13 12:46:58 DSP LOG 0 Home X Back
Fri 06/07/13 12:46:59 HMS_RCVR RECOVERY_CHECK_SOLENOID_2 0
Fri 06/07/13 12:46:59 HMS_RCVR RECOVERY_CHECK_SOLENOID_DISENGAGED 0
Fri 06/07/13 12:46:59 DSP LOG 0 Home X Back
Fri 06/07/13 12:47:00 HMS_RCVR RECOVERY_CHECK_SOLENOID_2 0
Fri 06/07/13 12:47:00 HMS_RCVR RECOVERY_CHECK_SOLENOID_DISENGAGED 0
Fri 06/07/13 12:47:01 DSP LOG 0 Home X Back
Fri 06/07/13 12:47:01 HMS_RCVR RECOVERY_CHECK_SOLENOID_2 0
Fri 06/07/13 12:47:01 HMS_RCVR RECOVERY_CHECK_SOLENOID_3 0
Fri 06/07/13 12:47:01 HMS_RCVR RECOVERY_ERROR_STATE 0 HMS solenoid disengage error
Fri 06/07/13 12:47:01 HMS_RCVR RECOVERY_DONE_STATE 0
Fri 06/07/13 12:47:01 DEBUG TEMP_STATE_CHANGE 3 Control Conserve
Fri 06/07/13 12:47:01 BUILD NON_BUILD_FATAL_ERROR 0
Fri 06/07/13 12:47:02 DSP LOCAL_LOG 0 Printhead Maintenance Error Recovery Failed
Fri 06/07/13 12:47:02 DSP LOCAL_LOG 0 Realtime GO_TO_ERROR
Fri 06/07/13 12:47:02 DSP LOCAL_LOG 0 Control Conserve Temperature
Fri 06/07/13 12:47:02 Exiting Application - Log Stopped
Fri 06/07/13 12:47:03 DEBUG PARAM_CHANGE 0 Change Modeler Type: ProJet SD
Fri 06/07/13 12:47:03 DEBUG PARAM_CHANGE 0 LoadBuildStyle: STANDARD FRACTAL
Fri 06/07/13 12:47:04 Log Started - ProJet SD 3000 1.06 Nov 21 2008 09:01:42
Fri 06/07/13 12:47:07 DEBUG PARAM_CHANGE 0 Change Modeler Type: ProJet SD
Fri 06/07/13 12:47:07 DEBUG PARAM_CHANGE 0 LoadBuildStyle: STANDARD FRACTAL
Fri 06/07/13 12:47:07 DEBUG NOTICE 0 Computer: PROJET_41018
Fri 06/07/13 12:47:07 DEBUG MACHINE_INI 0 Creation Time: 11/16/09 18:42:56
Fri 06/07/13 12:47:07 DEBUG MACHINE_INI 0 Last Modify Time: 06/07/13 12:47:01
Fri 06/07/13 12:47:07 DEBUG MACHINE_INI 0 Machine Hours: 28471.64
Fri 06/07/13 12:47:07 DEBUG MACHINE_INI 0 Build Hours : 879.89
Fri 06/07/13 12:47:07 DEBUG MACHINE_INI 0 Lamp Hours : 164.00
Fri 06/07/13 12:47:07 DEBUG MACHINE_INI 0 Part Cartridges: 68
Fri 06/07/13 12:47:07 DEBUG MACHINE_INI 0 Support Cartridges: 144
Fri 06/07/13 12:47:07 DEBUG NOTICE 0 FPGA Combined Signature: 12
Fri 06/07/13 12:47:10 DEBUG NOTICE 0 Material Control Type 2 board initialization version numbers:RFID: 021; Part: 023; Support 023
Fri 06/07/13 12:47:10 DEBUG NOTICE 0 Clamp Feed System found installed **********************
Fri 06/07/13 12:47:10 DEBUG NOTICE 0 Hi Res mode: 1
Fri 06/07/13 12:47:10 DEBUG NORMALIZATION 5 Waveform: 5
Fri 06/07/13 12:47:10 DEBUG NORMALIZATION 1 Support Group 1: 1
Fri 06/07/13 12:47:10 DEBUG NORMALIZATION 2 Support Group 2: 2
Fri 06/07/13 12:47:10 DEBUG NORMALIZATION 1 Support Group 3: 1
Fri 06/07/13 12:47:10 DEBUG NORMALIZATION 2 Support Group 4: 2
Fri 06/07/13 12:47:10 DEBUG NORMALIZATION 1 Support Group 5: 1
Fri 06/07/13 12:47:10 DEBUG NORMALIZATION 2 Support Group 6: 2
Fri 06/07/13 12:47:10 DEBUG NORMALIZATION 0 Support Group 7: 0
Fri 06/07/13 12:47:10 DEBUG NORMALIZATION 1 Part Group 1: 1
Fri 06/07/13 12:47:10 DEBUG NORMALIZATION 1 Part Group 2: 1
Fri 06/07/13 12:47:10 DEBUG NORMALIZATION 1 Part Group 3: 1
Fri 06/07/13 12:47:10 DEBUG NORMALIZATION 2 Part Group 4: 2
Fri 06/07/13 12:47:10 DEBUG NORMALIZATION 1 Part Group 5: 1
Fri 06/07/13 12:47:10 DEBUG NORMALIZATION 1 Part Group 6: 1
Fri 06/07/13 12:47:10 DEBUG NORMALIZATION 0 Part Group 7: 0
Fri 06/07/13 12:47:10 DEBUG NOTICE 0 Send Parameters To DSP
Fri 06/07/13 12:47:10 SUP_IDX MS_INITIALIZE 0 Initialize D&K Support Feed System
Fri 06/07/13 12:47:10 PRT_IDX MS_INITIALIZE 0 Initialize D&K Part Feed System
Fri 06/07/13 12:47:10 DEBUG TEMP_STATE_CHANGE 4 Adapter Build
Fri 06/07/13 12:47:10 HMS WIPE_INACTIVE 0
Fri 06/07/13 12:47:10 HMS_RCVR RECOVERY_INACTIVE 0
Fri 06/07/13 12:47:11 PREP IDLE 0
Fri 06/07/13 12:47:11 DSP LOG 0 Comm Channel Opened
Fri 06/07/13 12:47:11 DSP LOG 0 SetResolutionMode : 1
Fri 06/07/13 12:47:11 DSP LOG 0 Entering Main Command Loop
Fri 06/07/13 12:47:11 DEBUG NOTICE 0 RmtDiag Listen

ing on 192.168.10.207 port 22376
Fri 06/07/13 12:47:11 DSP LOG 0 Servo Disabled by PC
Fri 06/07/13 12:47:11 DSP LOG 0 SetResolutionMode : 1
Fri 06/07/13 12:47:11 DSP LOG 0 Init Supp Indexer to 0.000000
Fri 06/07/13 12:47:11 DSP LOG 0 Init Part Indexer to 0.000000
Fri 06/07/13 12:47:11 DEBUG NOTICE 0 Listen

ing on 192.168.10.207 port 22375
Fri 06/07/13 12:47:11 DSP LOG 0 Init Supp Plunger to 1.176999
Fri 06/07/13 12:47:11 DSP LOG 0 Init Part Plunger to 0.152000
Fri 06/07/13 12:47:11 DEBUG NOTICE 0 UDP Socket on 192.168.10.207 port 22377
Fri 06/07/13 12:47:11 DEBUG NOTICE 0 Diag2 Listen

ing on 0.0.0.0 port 1049
Fri 06/07/13 12:47:11 DEBUG NOTICE 0 Security Listen

ing on 192.168.10.207 port 22378
Fri 06/07/13 12:47:11 DEBUG NOTICE 0 UDP Security Socket on 192.168.10.207 port 22378
Fri 06/07/13 12:47:11 DEBUG TEMP_STATE_CHANGE 5 Reservoir Build
Fri 06/07/13 12:47:11 SUP_IDX IDLE 0 Cartridges and plunger found in feed positions
Fri 06/07/13 12:47:11 PRT_IDX IDLE 0 Cartridges and plunger found in feed positions
Fri 06/07/13 12:47:11 DEBUG TEMP_STATE_CHANGE 4 Adapter Build
Fri 06/07/13 12:47:11 DEBUG TEMP_STATE_CHANGE 5 Reservoir Build
Fri 06/07/13 12:47:11 DSP LOCAL_LOG 0 Found 3 Support cartridges. From 012
Fri 06/07/13 12:47:11 DEBUG TEMP_STATE_CHANGE 6 Jetstack Delay; Delay: 10
Fri 06/07/13 12:47:11 DSP LOCAL_LOG 0 Found 3 Part cartridges. From 012
Fri 06/07/13 12:47:11 DSP LOCAL_LOG 0 Realtime GO_TO_BUILD
Fri 06/07/13 12:47:11 DSP LOCAL_LOG 0 Machine Off Time Sets Delay
Fri 06/07/13 12:47:12 DSP LOCAL_LOG 0 Jetstack Delay = 10 Minutes
Fri 06/07/13 12:47:17 DEBUG NOTICE 0 MQG Bypass Enabled
Fri 06/07/13 12:47:18 SUPPORT CHANGE_CARTRIDGE 0
Fri 06/07/13 12:47:18 PART CHANGE_CARTRIDGE 0
Fri 06/07/13 12:47:18 DEBUG PARAM_CHANGE 0 LoadBuildStyle: SD FRACTAL
Fri 06/07/13 12:47:18 BUILD INITIALIZATION 0
Fri 06/07/13 12:47:18 BUILD WAIT_READY 0
Fri 06/07/13 12:47:18 BUILD PRE_JOB_CHECKS 0
Fri 06/07/13 12:47:21 DEBUG NOTICE 0 Send Parameters To DSP
Fri 06/07/13 12:57:11 DEBUG TEMP_STATE_CHANGE 7 Control Build; Delay: 10
Fri 06/07/13 12:57:40 DEBUG TEMP_STATE_CHANGE 7 Control Build; Delay: 10
Fri 06/07/13 12:57:40 DSP LOG 0 Servo Enabled by PC
Fri 06/07/13 12:57:40 DSP LOCAL_LOG 0 Realtime READY_TO_BUILD
Fri 06/07/13 12:57:41 BUILD HMS_ERROR_RECOVERY 0
Fri 06/07/13 12:57:41 HMS_RCVR RECOVERY_BEGIN 0
Fri 06/07/13 12:57:41 HMS_RCVR RECOVERY_MOVE_ZX 0 ServiceHmsRecovery Error State = 4
Fri 06/07/13 12:57:41 DSP LOCAL_LOG 0 ServiceHmsRecovery Error State = 4; Move Z
Fri 06/07/13 12:58:01 HMS_RCVR RECOVERY_MOVE_XZ 0
Fri 06/07/13 12:58:01 DSP LOCAL_LOG 0 ServiceHmsRecovery Error State = 4; Home X
Fri 06/07/13 12:58:01 DSP LOG 0 Home X Back
Fri 06/07/13 12:58:02 HMS_RCVR RECOVERY_DISENGAGE_SOLENOID 0
Fri 06/07/13 12:58:04 HMS_RCVR RECOVERY_CHECK_SOLENOID_DISENGAGED 0
Fri 06/07/13 12:58:04 DSP LOG 0 Home X Back
Fri 06/07/13 12:58:05 HMS_RCVR RECOVERY_CHECK_SOLENOID_2 0
Fri 06/07/13 12:58:05 HMS_RCVR RECOVERY_CHECK_SOLENOID_DISENGAGED 0
Fri 06/07/13 12:58:05 DSP LOG 0 Home X Back
Fri 06/07/13 12:58:06 HMS_RCVR RECOVERY_CHECK_SOLENOID_2 0
Fri 06/07/13 12:58:06 HMS_RCVR RECOVERY_CHECK_SOLENOID_DISENGAGED 0
Fri 06/07/13 12:58:06 DSP LOG 0 Home X Back
Fri 06/07/13 12:58:07 HMS_RCVR RECOVERY_CHECK_SOLENOID_2 0
Fri 06/07/13 12:58:07 HMS_RCVR RECOVERY_CHECK_SOLENOID_DISENGAGED 0
Fri 06/07/13 12:58:07 DSP LOG 0 Home X Back
Fri 06/07/13 12:58:08 HMS_RCVR RECOVERY_CHECK_SOLENOID_2 0
Fri 06/07/13 12:58:08 HMS_RCVR RECOVERY_CHECK_SOLENOID_3 0
Fri 06/07/13 12:58:08 HMS_RCVR RECOVERY_ERROR_STATE 0 HMS solenoid disengage error
Fri 06/07/13 12:58:08 HMS_RCVR RECOVERY_DONE_STATE 0
Fri 06/07/13 12:58:08 DEBUG TEMP_STATE_CHANGE 3 Control Conserve
Fri 06/07/13 12:58:08 DSP LOCAL_LOG 0 Printhead Maintenance Error Recovery Failed
Fri 06/07/13 12:58:09 BUILD NON_BUILD_FATAL_ERROR 0
Fri 06/07/13 12:58:09 DSP LOCAL_LOG 0 Realtime GO_TO_ERROR
Fri 06/07/13 12:58:09 DSP LOCAL_LOG 0 Control Conserve Temperature
Fri 06/07/13 13:21:00 DEBUG PARAM_CHANGE 0 Change Modeler Type: ProJet SD
Fri 06/07/13 13:21:00 DEBUG PARAM_CHANGE 0 LoadBuildStyle: STANDARD FRACTAL
Fri 06/07/13 13:21:01 Log Started - ProJet SD 3000 1.06 Nov 21 2008 09:01:42
Fri 06/07/13 13:21:04 DEBUG PARAM_CHANGE 0 Change Modeler Type: ProJet SD
Fri 06/07/13 13:21:04 DEBUG PARAM_CHANGE 0 LoadBuildStyle: STANDARD FRACTAL
Fri 06/07/13 13:21:04 DEBUG NOTICE 0 Computer: PROJET_41018
Fri 06/07/13 13:21:04 DEBUG MACHINE_INI 0 Creation Time: 11/16/09 18:42:56
Fri 06/07/13 13:21:04 DEBUG MACHINE_INI 0 Last Modify Time: 06/07/13 13:12:41
Fri 06/07/13 13:21:04 DEBUG MACHINE_INI 0 Machine Hours: 28472.04
Fri 06/07/13 13:21:04 DEBUG MACHINE_INI 0 Build Hours : 879.89
Fri 06/07/13 13:21:04 DEBUG MACHINE_INI 0 Lamp Hours : 164.00
Fri 06/07/13 13:21:04 DEBUG MACHINE_INI 0 Part Cartridges: 68
Fri 06/07/13 13:21:04 DEBUG MACHINE_INI 0 Support Cartridges: 144
Fri 06/07/13 13:21:04 DEBUG NOTICE 0 FPGA Combined Signature: 12
Fri 06/07/13 13:21:06 DEBUG NOTICE 0 Material Control Type 2 board initialization version numbers:RFID: 021; Part: 023; Support 023
Fri 06/07/13 13:21:06 DEBUG NOTICE 0 Clamp Feed System found installed **********************
Fri 06/07/13 13:21:06 DEBUG NOTICE 0 Hi Res mode: 1
Fri 06/07/13 13:21:06 DEBUG NORMALIZATION 5 Waveform: 5
Fri 06/07/13 13:21:06 DEBUG NORMALIZATION 1 Support Group 1: 1
Fri 06/07/13 13:21:06 DEBUG NORMALIZATION 2 Support Group 2: 2
Fri 06/07/13 13:21:06 DEBUG NORMALIZATION 1 Support Group 3: 1
Fri 06/07/13 13:21:06 DEBUG NORMALIZATION 2 Support Group 4: 2
Fri 06/07/13 13:21:06 DEBUG NORMALIZATION 1 Support Group 5: 1
Fri 06/07/13 13:21:06 DEBUG NORMALIZATION 2 Support Group 6: 2
Fri 06/07/13 13:21:06 DEBUG NORMALIZATION 0 Support Group 7: 0
Fri 06/07/13 13:21:06 DEBUG NORMALIZATION 1 Part Group 1: 1
Fri 06/07/13 13:21:06 DEBUG NORMALIZATION 1 Part Group 2: 1
Fri 06/07/13 13:21:06 DEBUG NORMALIZATION 1 Part Group 3: 1
Fri 06/07/13 13:21:06 DEBUG NORMALIZATION 2 Part Group 4: 2
Fri 06/07/13 13:21:06 DEBUG NORMALIZATION 1 Part Group 5: 1
Fri 06/07/13 13:21:06 DEBUG NORMALIZATION 1 Part Group 6: 1
Fri 06/07/13 13:21:06 DEBUG NORMALIZATION 0 Part Group 7: 0
Fri 06/07/13 13:21:07 DEBUG NOTICE 0 Send Parameters To DSP
Fri 06/07/13 13:21:07 SUP_IDX MS_INITIALIZE 0 Initialize D&K Support Feed System
Fri 06/07/13 13:21:07 PRT_IDX MS_INITIALIZE 0 Initialize D&K Part Feed System
Fri 06/07/13 13:21:07 DEBUG TEMP_STATE_CHANGE 4 Adapter Build
Fri 06/07/13 13:21:07 HMS WIPE_INACTIVE 0
Fri 06/07/13 13:21:07 HMS_RCVR RECOVERY_INACTIVE 0
Fri 06/07/13 13:21:08 PREP IDLE 0
Fri 06/07/13 13:21:08 DSP LOG 0 Comm Channel Opened
Fri 06/07/13 13:21:08 DSP LOG 0 SetResolutionMode : 1
Fri 06/07/13 13:21:08 DSP LOG 0 Entering Main Command Loop
Fri 06/07/13 13:21:08 DSP LOG 0 Servo Disabled by PC
Fri 06/07/13 13:21:08 DSP LOG 0 SetResolutionMode : 1
Fri 06/07/13 13:21:08 DSP LOG 0 Init Supp Indexer to 0.000000
Fri 06/07/13 13:21:08 DSP LOG 0 Init Part Indexer to 0.000000
Fri 06/07/13 13:21:08 DSP LOG 0 Init Supp Plunger to 1.176999
Fri 06/07/13 13:21:08 DEBUG NOTICE 0 RmtDiag Listen

ing on 192.168.10.207 port 22376
Fri 06/07/13 13:21:08 DSP LOG 0 Init Part Plunger to 0.152000
Fri 06/07/13 13:21:08 DEBUG NOTICE 0 Listen

ing on 192.168.10.207 port 22375
Fri 06/07/13 13:21:08 DEBUG NOTICE 0 UDP Socket on 192.168.10.207 port 22377
Fri 06/07/13 13:21:08 DEBUG NOTICE 0 Diag2 Listen

ing on 0.0.0.0 port 1027
Fri 06/07/13 13:21:08 DEBUG NOTICE 0 Security Listen

ing on 192.168.10.207 port 22378
Fri 06/07/13 13:21:08 DEBUG NOTICE 0 UDP Security Socket on 192.168.10.207 port 22378
Fri 06/07/13 13:21:08 SUP_IDX IDLE 0 Cartridges and plunger found in feed positions
Fri 06/07/13 13:21:08 PRT_IDX IDLE 0 Cartridges and plunger found in feed positions
Fri 06/07/13 13:21:08 DEBUG TEMP_STATE_CHANGE 4 Adapter Build
Fri 06/07/13 13:21:08 DSP LOCAL_LOG 0 Found 3 Support cartridges. From 012
Fri 06/07/13 13:21:08 DSP LOCAL_LOG 0 Found 3 Part cartridges. From 012
Fri 06/07/13 13:21:08 DSP LOCAL_LOG 0 Realtime GO_TO_BUILD
Fri 06/07/13 13:21:08 DSP LOCAL_LOG 0 Machine Off Time Sets Delay
Fri 06/07/13 13:21:08 DSP LOCAL_LOG 0 Jetstack Delay = 10 Minutes
Fri 06/07/13 13:21:15 DEBUG NOTICE 0 MQG Bypass Enabled
Fri 06/07/13 13:21:15 SUPPORT CHANGE_CARTRIDGE 0
Fri 06/07/13 13:21:15 PART CHANGE_CARTRIDGE 0
Fri 06/07/13 13:21:15 DEBUG PARAM_CHANGE 0 LoadBuildStyle: SD FRACTAL
Fri 06/07/13 13:21:15 BUILD INITIALIZATION 0
Fri 06/07/13 13:21:15 BUILD WAIT_READY 0
Fri 06/07/13 13:21:16 BUILD PRE_JOB_CHECKS 0
Fri 06/07/13 13:21:18 DEBUG NOTICE 0 Send Parameters To DSP
Fri 06/07/13 13:30:20 DEBUG TEMP_STATE_CHANGE 5 Reservoir Build
Fri 06/07/13 13:33:02 DEBUG TEMP_STATE_CHANGE 6 Jetstack Delay; Delay: 10
Fri 06/07/13 13:43:02 DEBUG TEMP_STATE_CHANGE 7 Control Build; Delay: 10
Fri 06/07/13 13:43:31 DEBUG TEMP_STATE_CHANGE 7 Control Build; Delay: 10
Fri 06/07/13 13:43:31 DSP LOCAL_LOG 0 Realtime READY_TO_BUILD
Fri 06/07/13 13:43:32 DSP LOG 0 Servo Enabled by PC
Fri 06/07/13 13:43:32 BUILD HMS_ERROR_RECOVERY 0
Fri 06/07/13 13:43:32 HMS_RCVR RECOVERY_BEGIN 0
Fri 06/07/13 13:43:32 HMS_RCVR RECOVERY_MOVE_ZX 0 ServiceHmsRecovery Error State = 4
Fri 06/07/13 13:43:32 DSP LOCAL_LOG 0 ServiceHmsRecovery Error State = 4; Move Z
Fri 06/07/13 13:43:52 HMS_RCVR RECOVERY_MOVE_XZ 0
Fri 06/07/13 13:43:52 DSP LOG 0 Home X Back
Fri 06/07/13 13:43:52 DSP LOCAL_LOG 0 ServiceHmsRecovery Error State = 4; Home X
Fri 06/07/13 13:43:53 HMS_RCVR RECOVERY_DISENGAGE_SOLENOID 0
Fri 06/07/13 13:43:55 HMS_RCVR RECOVERY_CHECK_SOLENOID_DISENGAGED 0
Fri 06/07/13 13:43:55 DSP LOG 0 Home X Back
Fri 06/07/13 13:43:56 HMS_RCVR RECOVERY_CHECK_SOLENOID_2 0
Fri 06/07/13 13:43:56 HMS_RCVR RECOVERY_CHECK_SOLENOID_DISENGAGED 0
Fri 06/07/13 13:43:56 DSP LOG 0 Home X Back
Fri 06/07/13 13:43:57 HMS_RCVR RECOVERY_CHECK_SOLENOID_2 0
Fri 06/07/13 13:43:57 HMS_RCVR RECOVERY_CHECK_SOLENOID_DISENGAGED 0
Fri 06/07/13 13:43:58 DSP LOG 0 Home X Back
Fri 06/07/13 13:43:58 HMS_RCVR RECOVERY_CHECK_SOLENOID_2 0
Fri 06/07/13 13:43:58 HMS_RCVR RECOVERY_CHECK_SOLENOID_DISENGAGED 0
Fri 06/07/13 13:43:58 DSP LOG 0 Home X Back
Fri 06/07/13 13:43:59 HMS_RCVR RECOVERY_CHECK_SOLENOID_2 0
Fri 06/07/13 13:43:59 HMS_RCVR RECOVERY_CHECK_SOLENOID_3 0
Fri 06/07/13 13:43:59 HMS_RCVR RECOVERY_ERROR_STATE 0 HMS solenoid disengage error
Fri 06/07/13 13:43:59 HMS_RCVR RECOVERY_DONE_STATE 0
Fri 06/07/13 13:43:59 DEBUG TEMP_STATE_CHANGE 3 Control Conserve
Fri 06/07/13 13:43:59 DSP LOCAL_LOG 0 Printhead Maintenance Error Recovery Failed
Fri 06/07/13 13:43:59 BUILD NON_BUILD_FATAL_ERROR 0
Fri 06/07/13 13:44:00 DSP LOCAL_LOG 0 Realtime GO_TO_ERROR
Fri 06/07/13 13:44:00 DSP LOCAL_LOG 0 Control Conserve Temperature
Fri 06/07/13 14:48:58 DIAG USER_VALIDATED 0 RmtDiag: User ProJet_RH logged on from machine 192.168.10.207 port 1037
Fri 06/07/13 14:49:04 DEBUG BTN_PRESSED 11 Yes Pressed
Fri 06/07/13 14:49:04 Exiting Application - Log Stopped
Fri 06/07/13 14:49:05 DEBUG PARAM_CHANGE 0 Change Modeler Type: ProJet SD
Fri 06/07/13 14:49:05 DEBUG PARAM_CHANGE 0 LoadBuildStyle: STANDARD FRACTAL
Fri 06/07/13 14:49:06 Log Started - ProJet SD 3000 1.06 Nov 21 2008 09:01:42
Fri 06/07/13 14:49:08 DEBUG PARAM_CHANGE 0 Change Modeler Type: ProJet SD
Fri 06/07/13 14:49:08 DEBUG PARAM_CHANGE 0 LoadBuildStyle: STANDARD FRACTAL
Fri 06/07/13 14:49:09 DEBUG NOTICE 0 Computer: PROJET_41018
Fri 06/07/13 14:49:09 DEBUG MACHINE_INI 0 Creation Time: 11/16/09 18:42:56
Fri 06/07/13 14:49:09 DEBUG MACHINE_INI 0 Last Modify Time: 06/07/13 14:48:32
Fri 06/07/13 14:49:09 DEBUG MACHINE_INI 0 Machine Hours: 28473.44
Fri 06/07/13 14:49:09 DEBUG MACHINE_INI 0 Build Hours : 879.89
Fri 06/07/13 14:49:09 DEBUG MACHINE_INI 0 Lamp Hours : 164.00
Fri 06/07/13 14:49:09 DEBUG MACHINE_INI 0 Part Cartridges: 68
Fri 06/07/13 14:49:09 DEBUG MACHINE_INI 0 Support Cartridges: 144
Fri 06/07/13 14:49:09 DEBUG NOTICE 0 FPGA Combined Signature: 12
Fri 06/07/13 14:49:11 DEBUG NOTICE 0 Material Control Type 2 board initialization version numbers:RFID: 021; Part: 023; Support 023
Fri 06/07/13 14:49:11 DEBUG NOTICE 0 Clamp Feed System found installed **********************
Fri 06/07/13 14:49:11 DEBUG NOTICE 0 Hi Res mode: 1
Fri 06/07/13 14:49:11 DEBUG NORMALIZATION 5 Waveform: 5
Fri 06/07/13 14:49:11 DEBUG NORMALIZATION 1 Support Group 1: 1
Fri 06/07/13 14:49:11 DEBUG NORMALIZATION 2 Support Group 2: 2
Fri 06/07/13 14:49:11 DEBUG NORMALIZATION 1 Support Group 3: 1
Fri 06/07/13 14:49:11 DEBUG NORMALIZATION 2 Support Group 4: 2
Fri 06/07/13 14:49:11 DEBUG NORMALIZATION 1 Support Group 5: 1
Fri 06/07/13 14:49:11 DEBUG NORMALIZATION 2 Support Group 6: 2
Fri 06/07/13 14:49:11 DEBUG NORMALIZATION 0 Support Group 7: 0
Fri 06/07/13 14:49:11 DEBUG NORMALIZATION 1 Part Group 1: 1
Fri 06/07/13 14:49:11 DEBUG NORMALIZATION 1 Part Group 2: 1
Fri 06/07/13 14:49:11 DEBUG NORMALIZATION 1 Part Group 3: 1
Fri 06/07/13 14:49:11 DEBUG NORMALIZATION 2 Part Group 4: 2
Fri 06/07/13 14:49:11 DEBUG NORMALIZATION 1 Part Group 5: 1
Fri 06/07/13 14:49:11 DEBUG NORMALIZATION 1 Part Group 6: 1
Fri 06/07/13 14:49:11 DEBUG NORMALIZATION 0 Part Group 7: 0
Fri 06/07/13 14:49:12 DEBUG NOTICE 0 Send Parameters To DSP
Fri 06/07/13 14:49:12 SUP_IDX MS_INITIALIZE 0 Initialize D&K Support Feed System
Fri 06/07/13 14:49:12 PRT_IDX MS_INITIALIZE 0 Initialize D&K Part Feed System
Fri 06/07/13 14:49:12 DEBUG TEMP_STATE_CHANGE 4 Adapter Build
Fri 06/07/13 14:49:12 HMS WIPE_INACTIVE 0
Fri 06/07/13 14:49:12 HMS_RCVR RECOVERY_INACTIVE 0
Fri 06/07/13 14:49:12 PREP IDLE 0
Fri 06/07/13 14:49:12 DSP LOG 0 Comm Channel Opened
Fri 06/07/13 14:49:12 DSP LOG 0 SetResolutionMode : 1
Fri 06/07/13 14:49:12 DSP LOG 0 Entering Main Command Loop
Fri 06/07/13 14:49:12 DEBUG NOTICE 0 RmtDiag Listen

ing on 192.168.10.207 port 22376
Fri 06/07/13 14:49:12 DSP LOG 0 Servo Disabled by PC
Fri 06/07/13 14:49:12 DSP LOG 0 SetResolutionMode : 1
Fri 06/07/13 14:49:12 DSP LOG 0 Init Supp Indexer to 0.000000
Fri 06/07/13 14:49:12 DSP LOG 0 Init Part Indexer to 0.000000
Fri 06/07/13 14:49:12 DEBUG NOTICE 0 Listen

ing on 192.168.10.207 port 22375
Fri 06/07/13 14:49:12 DSP LOG 0 Init Supp Plunger to 1.176999
Fri 06/07/13 14:49:12 DSP LOG 0 Init Part Plunger to 0.152000
Fri 06/07/13 14:49:12 DEBUG NOTICE 0 UDP Socket on 192.168.10.207 port 22377
Fri 06/07/13 14:49:12 DEBUG NOTICE 0 Diag2 Listen

ing on 0.0.0.0 port 1040
Fri 06/07/13 14:49:12 DEBUG NOTICE 0 Security Listen

ing on 192.168.10.207 port 22378
Fri 06/07/13 14:49:13 DEBUG NOTICE 0 UDP Security Socket on 192.168.10.207 port 22378
Fri 06/07/13 14:49:13 SUP_IDX IDLE 0 Cartridges and plunger found in feed positions
Fri 06/07/13 14:49:13 PRT_IDX IDLE 0 Cartridges and plunger found in feed positions
Fri 06/07/13 14:49:13 DEBUG TEMP_STATE_CHANGE 4 Adapter Build
Fri 06/07/13 14:49:13 DSP LOCAL_LOG 0 Found 3 Support cartridges. From 012
Fri 06/07/13 14:49:13 DSP LOCAL_LOG 0 Found 3 Part cartridges. From 012
Fri 06/07/13 14:49:13 DSP LOCAL_LOG 0 Realtime GO_TO_BUILD
Fri 06/07/13 14:49:13 DSP LOCAL_LOG 0 Machine Off Time Sets Delay
Fri 06/07/13 14:49:13 DSP LOCAL_LOG 0 Jetstack Delay = 10 Minutes
Fri 06/07/13 14:49:14 DIAG USER_VALIDATED 0 RmtDiag: User ProJet_RH logged on from machine 192.168.10.207 port 1043
Fri 06/07/13 14:49:19 DEBUG NOTICE 0 MQG Bypass Enabled
Fri 06/07/13 14:49:19 SUPPORT CHANGE_CARTRIDGE 0
Fri 06/07/13 14:49:19 PART CHANGE_CARTRIDGE 0
Fri 06/07/13 14:49:19 DEBUG PARAM_CHANGE 0 LoadBuildStyle: SD FRACTAL
Fri 06/07/13 14:49:20 BUILD INITIALIZATION 0
Fri 06/07/13 14:49:20 BUILD WAIT_READY 0
Fri 06/07/13 14:49:20 BUILD PRE_JOB_CHECKS 0
Fri 06/07/13 14:49:23 DEBUG NOTICE 0 Send Parameters To DSP

DMC · Jun 7, 2013

I don't think you copyied anything of use.
You are missing the section when the failure happened.
Only posted info after the fact.

But, I do see your MQG is disabled. Cool for you! (Material Quality Guarranty)

Seems your printer is "open" to accept any material you want.

Don't change your software version, or it will be re-enabled. No updates.

DMC · Jun 7, 2013

You have weird settings.

Waveform is kinda high at 5

All normalization values are low and One or more is at Zero.

I did not think zero was a possibility? Who calibrated your printer??

I bet your are wasting mucho material and your waste bag fills pretty quickly, right?

Printer is jetting out too much material for each layer.

Eugene_M · Jun 10, 2013

Scott, could you tell me about MQG, how can i disable it? in our new printer don't reading a bottle.

DMC · Jun 10, 2013

I do not understand your problem.

I do not know how to disable the MQG.

ProJetter, in Germany will do it for a fee.

I just manually shove the tubes in from the bottom and skip the MQG.

It is a PITA.

Eugene_M · Jun 10, 2013

I know about ProJetter, but he is on vacation now( unfortunately, i can't shove the tubes, coz it is dp 3510 ((

rh3000 · Jun 10, 2013

*** said:
I don't think you copyied anything of use.
You are missing the section when the failure happened.
Only posted info after the fact.

But, I do see your MQG is disabled. Cool for you! (Material Quality Guarranty)

Seems your printer is "open" to accept any material you want.

Don't change your software version, or it will be re-enabled. No updates.

Thanks for the heads up. yeah we had some problems when the machine would spit out ALL cartridges...not fun. They gave us the "disarm code" so I believe it is unique to each machine.

I believe I got the right log range this time, see below. Again, thanks a ton for your time with this.

Code:

Fri 04/12/13 16:46:01 DEBUG    BTN_PRESSED    3 Test Pressed
Fri 04/12/13 16:46:01 BUILD    PRE_JOB_CHECKS    0
Fri 04/12/13 16:46:04 DEBUG    BTN_PRESSED   11 Yes Pressed
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Send Parameters To DSP
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Number of post cure passes = 10
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 0 = 1, Cure Alt Pass 0 = 1
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 1 = 1, Cure Alt Pass 1 = 1
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 2 = 1, Cure Alt Pass 2 = 1
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 3 = 1, Cure Alt Pass 3 = 1
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 4 = 1, Cure Alt Pass 4 = 1
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 5 = 1, Cure Alt Pass 5 = 1
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 6 = 1, Cure Alt Pass 6 = 1
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 7 = 0, Cure Alt Pass 7 = 0
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 8 = 0, Cure Alt Pass 8 = 0
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 9 = 0, Cure Alt Pass 9 = 0
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 10 = 0, Cure Alt Pass 10 = 0
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 11 = 0, Cure Alt Pass 11 = 0
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 12 = 0, Cure Alt Pass 12 = 0
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 13 = 0, Cure Alt Pass 13 = 0
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 14 = 0, Cure Alt Pass 14 = 0
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 15 = 0, Cure Alt Pass 15 = 0
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 16 = 0, Cure Alt Pass 16 = 0
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 17 = 0, Cure Alt Pass 17 = 0
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 18 = 0, Cure Alt Pass 18 = 0
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 19 = 0, Cure Alt Pass 19 = 0
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 20 = 0, Cure Alt Pass 20 = 0
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 21 = 0, Cure Alt Pass 21 = 0
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 22 = 0, Cure Alt Pass 22 = 0
Fri 04/12/13 16:46:06 DEBUG    NOTICE         0 Updated DSP params.  CurePass 23 = 0, Cure Alt Pass 23 = 0
Fri 04/12/13 16:46:06 DEBUG    TEMP_STATE_CHANGE    7 Control Build; Delay: 10
Fri 04/12/13 16:46:06 DSP      LOCAL_LOG       0 Realtime GO_TO_BUILD
Fri 04/12/13 16:46:06 DSP      LOCAL_LOG       0 Realtime READY_TO_BUILD
Fri 04/12/13 16:46:06 DSP      LOG             0 Servo Enabled by PC
Fri 04/12/13 16:46:06 BUILD    HOME_XY         0
Fri 04/12/13 16:46:07 DSP      LOG             0 Home X
Fri 04/12/13 16:46:08 DSP      LOG             0 Detected X Limit
Fri 04/12/13 16:46:08 DSP      LOG             0 Home Y
Fri 04/12/13 16:46:17 DSP      LOG             0 Detected Y Limit
Fri 04/12/13 16:46:17 BUILD    HOME_Z          0
Fri 04/12/13 16:46:18 DSP      LOG             0 Home Z
Fri 04/12/13 16:47:50 DSP      LOG             0 Z Right Limit Detected
Fri 04/12/13 16:47:50 DSP      LOG             0 Z Left Limit Detected
Fri 04/12/13 16:47:50 DSP      LOG             0 Delta Z set to -0.015000
Fri 04/12/13 16:47:50 BUILD    HEAD_CLEANING    0
Fri 04/12/13 16:47:51 HMS      WIPE_INITIATE    0 Materials Present - Head Cleaning Initiated
Fri 04/12/13 16:47:51 HMS      WIPE_MOVE_Z_TO_PICKUP    0 Beginning Printhead Maintenance
Fri 04/12/13 16:48:28 DSP      LOG             0 X Following Error, Error Value = -0.100420 Encoder = 25.897394
Fri 04/12/13 16:48:28 HMS      WIPE_ERROR_STATE    0 Position error - was 25.906561, expected -0.050000 during state HMS
Fri 04/12/13 16:48:29 HMS      WIPE_ERROR_STATE_2    0 Error 4 During Printhead Maintenance
Fri 04/12/13 16:48:29 BUILD    NON_BUILD_ERROR    1 X FOLLOWING ERROR
Fri 04/12/13 16:48:29 BUILD    NON_BUILD_ERROR_RECOVERY    1 X FOLLOWING ERROR
Fri 04/12/13 16:48:29 BUILD    NON_BUILD_FATAL_ERROR   0
Fri 04/12/13 16:48:29 DEBUG    TEMP_STATE_CHANGE    3 Control Conserve
Fri 04/12/13 16:48:29 DSP      LOCAL_LOG       0 Realtime GO_TO_ERROR
Fri 04/12/13 16:48:30 DSP      LOCAL_LOG       0 Control Conserve Temperature
Fri 04/12/13 17:32:38 DEBUG    BTN_PRESSED   11 Yes Pressed
Fri 04/12/13 17:32:38 Exiting Application - Log Stopped
Fri 04/12/13 17:32:39 DEBUG    NOTICE         0 Setting curing parameters for material 0, 'CURING PARAMETERS'
Fri 04/12/13 17:32:39 DEBUG    NOTICE         0 Loading build temps from 'BUILD TEMPERATURE SETPOINTS'
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Cure Passes = 10
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 0 = 0.  AltCurePass 0 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 1 = 1.  AltCurePass 1 = 1
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 2 = 0.  AltCurePass 2 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 3 = 1.  AltCurePass 3 = 1
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 4 = 0.  AltCurePass 4 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 5 = 1.  AltCurePass 5 = 1
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 6 = 0.  AltCurePass 6 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 7 = 1.  AltCurePass 7 = 1
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 8 = 0.  AltCurePass 8 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 9 = 0.  AltCurePass 9 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 10 = 0.  AltCurePass 10 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 11 = 0.  AltCurePass 11 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 12 = 0.  AltCurePass 12 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 13 = 0.  AltCurePass 13 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 14 = 0.  AltCurePass 14 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 15 = 0.  AltCurePass 15 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 16 = 0.  AltCurePass 16 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 17 = 0.  AltCurePass 17 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 18 = 0.  AltCurePass 18 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 19 = 0.  AltCurePass 19 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 20 = 0.  AltCurePass 20 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 21 = 0.  AltCurePass 21 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 22 = 0.  AltCurePass 22 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 23 = 0.  AltCurePass 23 = 0
Fri 04/12/13 17:32:40 DEBUG    PARAM_CHANGE    0 Change Modeler Type: ProJet SD
Fri 04/12/13 17:32:40 DEBUG    PARAM_CHANGE    0 LoadBuildStyle: STANDARD FRACTAL
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Cure Passes = 10
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 0 = 1.  AltCurePass 0 = 1
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 1 = 1.  AltCurePass 1 = 1
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 2 = 1.  AltCurePass 2 = 1
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 3 = 1.  AltCurePass 3 = 1
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 4 = 1.  AltCurePass 4 = 1
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 5 = 1.  AltCurePass 5 = 1
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 6 = 1.  AltCurePass 6 = 1
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 7 = 0.  AltCurePass 7 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 8 = 0.  AltCurePass 8 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 9 = 0.  AltCurePass 9 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 10 = 0.  AltCurePass 10 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 11 = 0.  AltCurePass 11 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 12 = 0.  AltCurePass 12 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 13 = 0.  AltCurePass 13 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 14 = 0.  AltCurePass 14 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 15 = 0.  AltCurePass 15 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 16 = 0.  AltCurePass 16 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 17 = 0.  AltCurePass 17 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 18 = 0.  AltCurePass 18 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 19 = 0.  AltCurePass 19 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 20 = 0.  AltCurePass 20 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 21 = 0.  AltCurePass 21 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 22 = 0.  AltCurePass 22 = 0
Fri 04/12/13 17:32:40 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 23 = 0.  AltCurePass 23 = 0
Fri 04/12/13 17:32:40 Log Started - ProJet SD 3000 1.10.576 Oct 22 2009 11:31:18
Fri 04/12/13 17:32:43 DEBUG    PARAM_CHANGE    0 Change Modeler Type: ProJet SD
Fri 04/12/13 17:32:43 DEBUG    PARAM_CHANGE    0 LoadBuildStyle: STANDARD FRACTAL
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Cure Passes = 10
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 0 = 1.  AltCurePass 0 = 1
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 1 = 1.  AltCurePass 1 = 1
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 2 = 1.  AltCurePass 2 = 1
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 3 = 1.  AltCurePass 3 = 1
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 4 = 1.  AltCurePass 4 = 1
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 5 = 1.  AltCurePass 5 = 1
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 6 = 1.  AltCurePass 6 = 1
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 7 = 0.  AltCurePass 7 = 0
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 8 = 0.  AltCurePass 8 = 0
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 9 = 0.  AltCurePass 9 = 0
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 10 = 0.  AltCurePass 10 = 0
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 11 = 0.  AltCurePass 11 = 0
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 12 = 0.  AltCurePass 12 = 0
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 13 = 0.  AltCurePass 13 = 0
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 14 = 0.  AltCurePass 14 = 0
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 15 = 0.  AltCurePass 15 = 0
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 16 = 0.  AltCurePass 16 = 0
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 17 = 0.  AltCurePass 17 = 0
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 18 = 0.  AltCurePass 18 = 0
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 19 = 0.  AltCurePass 19 = 0
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 20 = 0.  AltCurePass 20 = 0
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 21 = 0.  AltCurePass 21 = 0
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 22 = 0.  AltCurePass 22 = 0
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 23 = 0.  AltCurePass 23 = 0
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 Computer: PROJET_41018
Fri 04/12/13 17:32:43 DEBUG    MACHINE_INI    0 Creation Time:    11/16/09 18:42:56
Fri 04/12/13 17:32:43 DEBUG    MACHINE_INI    0 Last Modify Time: 04/12/13 17:30:18
Fri 04/12/13 17:32:43 DEBUG    MACHINE_INI    0 Machine Hours: 27251.12
Fri 04/12/13 17:32:43 DEBUG    MACHINE_INI    0 Build Hours  : 879.89
Fri 04/12/13 17:32:43 DEBUG    MACHINE_INI    0 Lamp Hours   : 164.00
Fri 04/12/13 17:32:43 DEBUG    MACHINE_INI    0 Part Cartridges:    68
Fri 04/12/13 17:32:43 DEBUG    MACHINE_INI    0 Support Cartridges: 144
Fri 04/12/13 17:32:43 DEBUG    NOTICE         0 FPGA Combined Signature: 12
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Material Control Type 2 board initialization version numbers:RFID: 021; Part: 023; Support 023
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Clamp Feed System found installed **********************
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Hi Res mode: 1
Fri 04/12/13 17:32:46 DEBUG    NORMALIZATION    5 Waveform: 5
Fri 04/12/13 17:32:46 DEBUG    NORMALIZATION    1 Support Group 1: 1
Fri 04/12/13 17:32:46 DEBUG    NORMALIZATION    2 Support Group 2: 2
Fri 04/12/13 17:32:46 DEBUG    NORMALIZATION    1 Support Group 3: 1
Fri 04/12/13 17:32:46 DEBUG    NORMALIZATION    2 Support Group 4: 2
Fri 04/12/13 17:32:46 DEBUG    NORMALIZATION    1 Support Group 5: 1
Fri 04/12/13 17:32:46 DEBUG    NORMALIZATION    2 Support Group 6: 2
Fri 04/12/13 17:32:46 DEBUG    NORMALIZATION    0 Support Group 7: 0
Fri 04/12/13 17:32:46 DEBUG    NORMALIZATION    1 Part Group 1: 1
Fri 04/12/13 17:32:46 DEBUG    NORMALIZATION    1 Part Group 2: 1
Fri 04/12/13 17:32:46 DEBUG    NORMALIZATION    1 Part Group 3: 1
Fri 04/12/13 17:32:46 DEBUG    NORMALIZATION    2 Part Group 4: 2
Fri 04/12/13 17:32:46 DEBUG    NORMALIZATION    1 Part Group 5: 1
Fri 04/12/13 17:32:46 DEBUG    NORMALIZATION    1 Part Group 6: 1
Fri 04/12/13 17:32:46 DEBUG    NORMALIZATION    0 Part Group 7: 0
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Send Parameters To DSP
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Number of post cure passes = 10
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 0 = 1, Cure Alt Pass 0 = 1
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 1 = 1, Cure Alt Pass 1 = 1
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 2 = 1, Cure Alt Pass 2 = 1
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 3 = 1, Cure Alt Pass 3 = 1
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 4 = 1, Cure Alt Pass 4 = 1
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 5 = 1, Cure Alt Pass 5 = 1
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 6 = 1, Cure Alt Pass 6 = 1
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 7 = 0, Cure Alt Pass 7 = 0
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 8 = 0, Cure Alt Pass 8 = 0
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 9 = 0, Cure Alt Pass 9 = 0
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 10 = 0, Cure Alt Pass 10 = 0
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 11 = 0, Cure Alt Pass 11 = 0
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 12 = 0, Cure Alt Pass 12 = 0
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 13 = 0, Cure Alt Pass 13 = 0
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 14 = 0, Cure Alt Pass 14 = 0
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 15 = 0, Cure Alt Pass 15 = 0
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 16 = 0, Cure Alt Pass 16 = 0
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 17 = 0, Cure Alt Pass 17 = 0
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 18 = 0, Cure Alt Pass 18 = 0
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 19 = 0, Cure Alt Pass 19 = 0
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 20 = 0, Cure Alt Pass 20 = 0
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 21 = 0, Cure Alt Pass 21 = 0
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 22 = 0, Cure Alt Pass 22 = 0
Fri 04/12/13 17:32:46 DEBUG    NOTICE         0 Updated DSP params.  CurePass 23 = 0, Cure Alt Pass 23 = 0
Fri 04/12/13 17:32:46 SUP_IDX  MS_INITIALIZE              0 Initialize D&K Support Feed System
Fri 04/12/13 17:32:46 PRT_IDX  MS_INITIALIZE              0 Initialize D&K Part Feed System
Fri 04/12/13 17:32:46 DEBUG    TEMP_STATE_CHANGE    4 Adapter Build
Fri 04/12/13 17:32:46 HMS      WIPE_INACTIVE    0
Fri 04/12/13 17:32:46 HMS_RCVR RECOVERY_INACTIVE            0
Fri 04/12/13 17:32:47 PREP     IDLE              0
Fri 04/12/13 17:32:47 DSP      LOG             0 Comm Channel Opened
Fri 04/12/13 17:32:47 DSP      LOG             0 SetResolutionMode : 1
Fri 04/12/13 17:32:47 DSP      LOG             0 Entering Main Command Loop
Fri 04/12/13 17:32:47 DEBUG    NOTICE         0 RmtDiag Listening on 192.168.10.207 port 22376
Fri 04/12/13 17:32:47 DSP      LOG             0 Servo Disabled by PC
Fri 04/12/13 17:32:47 DSP      LOG             0 SetResolutionMode : 1
Fri 04/12/13 17:32:47 DSP      LOG             0 Init Supp Indexer to  0.000000
Fri 04/12/13 17:32:47 DSP      LOG             0 Init Part Indexer to  0.000000
Fri 04/12/13 17:32:47 DEBUG    NOTICE         0 Listening on 192.168.10.207 port 22375
Fri 04/12/13 17:32:47 DSP      LOG             0 Init Supp Plunger to  1.176999
Fri 04/12/13 17:32:47 DSP      LOG             0 Init Part Plunger to  0.152000
Fri 04/12/13 17:32:47 DEBUG    NOTICE         0 UDP Socket on 192.168.10.207 port 22377
Fri 04/12/13 17:32:47 DEBUG    NOTICE         0 Diag2 Listening on 0.0.0.0 port 1059
Fri 04/12/13 17:32:47 DEBUG    NOTICE         0 Security Listening on 192.168.10.207 port 22378
Fri 04/12/13 17:32:47 DEBUG    NOTICE         0 UDP Security Socket on 192.168.10.207 port 22378
Fri 04/12/13 17:32:47 SUP_IDX  IDLE                       0 Cartridges and plunger found in feed positions
Fri 04/12/13 17:32:47 PRT_IDX  IDLE                       0 Cartridges and plunger found in feed positions
Fri 04/12/13 17:32:47 DEBUG    TEMP_STATE_CHANGE    4 Adapter Build
Fri 04/12/13 17:32:47 DSP      LOCAL_LOG       0 Found 3 Support cartridges. From 012
Fri 04/12/13 17:32:47 DSP      LOCAL_LOG       0 Found 3 Part cartridges. From 012
Fri 04/12/13 17:32:48 DSP      LOCAL_LOG       0 Realtime GO_TO_BUILD
Fri 04/12/13 17:32:48 DSP      LOCAL_LOG       0 Machine Off Time Sets Delay
Fri 04/12/13 17:32:48 DSP      LOCAL_LOG       0 Jetstack Delay = 10 Minutes
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 MQG Bypass Enabled
Fri 04/12/13 17:32:54 SUPPORT  CHANGE_CARTRIDGE       0
Fri 04/12/13 17:32:54 PART     CHANGE_CARTRIDGE       0
Fri 04/12/13 17:32:54 DEBUG    PARAM_CHANGE    0 LoadBuildStyle: SD FRACTAL
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Cure Passes = 10
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 0 = 1.  AltCurePass 0 = 1
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 1 = 1.  AltCurePass 1 = 1
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 2 = 1.  AltCurePass 2 = 1
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 3 = 1.  AltCurePass 3 = 1
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 4 = 1.  AltCurePass 4 = 1
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 5 = 1.  AltCurePass 5 = 1
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 6 = 1.  AltCurePass 6 = 1
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 7 = 0.  AltCurePass 7 = 0
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 8 = 0.  AltCurePass 8 = 0
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 9 = 0.  AltCurePass 9 = 0
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 10 = 0.  AltCurePass 10 = 0
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 11 = 0.  AltCurePass 11 = 0
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 12 = 0.  AltCurePass 12 = 0
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 13 = 0.  AltCurePass 13 = 0
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 14 = 0.  AltCurePass 14 = 0
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 15 = 0.  AltCurePass 15 = 0
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 16 = 0.  AltCurePass 16 = 0
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 17 = 0.  AltCurePass 17 = 0
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 18 = 0.  AltCurePass 18 = 0
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 19 = 0.  AltCurePass 19 = 0
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 20 = 0.  AltCurePass 20 = 0
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 21 = 0.  AltCurePass 21 = 0
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 22 = 0.  AltCurePass 22 = 0
Fri 04/12/13 17:32:54 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 23 = 0.  AltCurePass 23 = 0
Fri 04/12/13 17:32:54 BUILD    INITIALIZATION    0
Fri 04/12/13 17:32:55 BUILD    WAIT_READY      0
Fri 04/12/13 17:32:55 BUILD    PRE_JOB_CHECKS    0
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Send Parameters To DSP
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Number of post cure passes = 10
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 0 = 1, Cure Alt Pass 0 = 1
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 1 = 1, Cure Alt Pass 1 = 1
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 2 = 1, Cure Alt Pass 2 = 1
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 3 = 1, Cure Alt Pass 3 = 1
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 4 = 1, Cure Alt Pass 4 = 1
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 5 = 1, Cure Alt Pass 5 = 1
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 6 = 1, Cure Alt Pass 6 = 1
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 7 = 0, Cure Alt Pass 7 = 0
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 8 = 0, Cure Alt Pass 8 = 0
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 9 = 0, Cure Alt Pass 9 = 0
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 10 = 0, Cure Alt Pass 10 = 0
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 11 = 0, Cure Alt Pass 11 = 0
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 12 = 0, Cure Alt Pass 12 = 0
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 13 = 0, Cure Alt Pass 13 = 0
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 14 = 0, Cure Alt Pass 14 = 0
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 15 = 0, Cure Alt Pass 15 = 0
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 16 = 0, Cure Alt Pass 16 = 0
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 17 = 0, Cure Alt Pass 17 = 0
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 18 = 0, Cure Alt Pass 18 = 0
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 19 = 0, Cure Alt Pass 19 = 0
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 20 = 0, Cure Alt Pass 20 = 0
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 21 = 0, Cure Alt Pass 21 = 0
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 22 = 0, Cure Alt Pass 22 = 0
Fri 04/12/13 17:32:57 DEBUG    NOTICE         0 Updated DSP params.  CurePass 23 = 0, Cure Alt Pass 23 = 0
Fri 04/12/13 17:45:05 DEBUG    TEMP_STATE_CHANGE    5 Reservoir Build
Fri 04/12/13 17:47:47 DEBUG    TEMP_STATE_CHANGE    6 Jetstack Delay; Delay: 10
Fri 04/12/13 17:57:47 DEBUG    TEMP_STATE_CHANGE    7 Control Build; Delay: 10
Fri 04/12/13 17:58:16 DEBUG    TEMP_STATE_CHANGE    7 Control Build; Delay: 10
Fri 04/12/13 17:58:16 DSP      LOCAL_LOG       0 Realtime READY_TO_BUILD
Fri 04/12/13 17:58:16 DSP      LOG             0 Servo Enabled by PC
Fri 04/12/13 17:58:17 BUILD    HMS_ERROR_RECOVERY    0
Fri 04/12/13 17:58:17 HMS_RCVR RECOVERY_BEGIN               0
Fri 04/12/13 17:58:17 HMS_RCVR RECOVERY_MOVE_ZX             0 ServiceHmsRecovery Error State = 4
Fri 04/12/13 17:58:17 DSP      LOCAL_LOG       0 ServiceHmsRecovery Error State = 4; Move Z
Fri 04/12/13 17:58:37 HMS_RCVR RECOVERY_MOVE_XZ             0
Fri 04/12/13 17:58:37 DSP      LOCAL_LOG       0 ServiceHmsRecovery Error State = 4; Home X
Fri 04/12/13 17:58:37 DSP      LOG             0 Home X Back
Fri 04/12/13 17:58:59 HMS_RCVR RECOVERY_DISENGAGE_SOLENOID    0
Fri 04/12/13 17:59:01 HMS_RCVR RECOVERY_CHECK_SOLENOID_DISENGAGED    0
Fri 04/12/13 17:59:02 DSP      LOG             0 Home X Back
Fri 04/12/13 17:59:02 HMS_RCVR RECOVERY_CHECK_SOLENOID_2    0
Fri 04/12/13 17:59:02 HMS_RCVR RECOVERY_CHECK_SOLENOID_DISENGAGED    0
Fri 04/12/13 17:59:02 DSP      LOG             0 Home X Back
Fri 04/12/13 17:59:03 HMS_RCVR RECOVERY_CHECK_SOLENOID_2    0
Fri 04/12/13 17:59:03 HMS_RCVR RECOVERY_CHECK_SOLENOID_DISENGAGED    0
Fri 04/12/13 17:59:04 DSP      LOG             0 Home X Back
Fri 04/12/13 17:59:04 HMS_RCVR RECOVERY_CHECK_SOLENOID_2    0
Fri 04/12/13 17:59:04 HMS_RCVR RECOVERY_CHECK_SOLENOID_DISENGAGED    0
Fri 04/12/13 17:59:05 DSP      LOG             0 Home X Back
Fri 04/12/13 17:59:05 HMS_RCVR RECOVERY_CHECK_SOLENOID_2    0
Fri 04/12/13 17:59:05 HMS_RCVR RECOVERY_CHECK_SOLENOID_3    0
Fri 04/12/13 17:59:05 HMS_RCVR RECOVERY_ERROR_STATE         0 HMS solenoid disengage error
Fri 04/12/13 17:59:05 HMS_RCVR RECOVERY_DONE_STATE          0
Fri 04/12/13 17:59:06 DEBUG    TEMP_STATE_CHANGE    3 Control Conserve
Fri 04/12/13 17:59:06 BUILD    NON_BUILD_FATAL_ERROR   0
Fri 04/12/13 17:59:06 DSP      LOCAL_LOG       0 Printhead Maintenance Error Recovery Failed
Fri 04/12/13 17:59:06 DSP      LOCAL_LOG       0 Realtime GO_TO_ERROR
Fri 04/12/13 17:59:06 DSP      LOCAL_LOG       0 Control Conserve Temperature
Mon 04/15/13 12:27:18 DEBUG    BTN_PRESSED   11 Yes Pressed
Mon 04/15/13 12:27:18 Exiting Application - Log Stopped
Mon 04/15/13 12:27:19 DEBUG    NOTICE         0 Setting curing parameters for material 0, 'CURING PARAMETERS'
Mon 04/15/13 12:27:19 DEBUG    NOTICE         0 Loading build temps from 'BUILD TEMPERATURE SETPOINTS'
Mon 04/15/13 12:27:19 DEBUG    NOTICE         0 Cure Passes = 10
Mon 04/15/13 12:27:19 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 0 = 0.  AltCurePass 0 = 0
Mon 04/15/13 12:27:19 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 1 = 1.  AltCurePass 1 = 1
Mon 04/15/13 12:27:19 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 2 = 0.  AltCurePass 2 = 0
Mon 04/15/13 12:27:19 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 3 = 1.  AltCurePass 3 = 1
Mon 04/15/13 12:27:19 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 4 = 0.  AltCurePass 4 = 0
Mon 04/15/13 12:27:19 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 5 = 1.  AltCurePass 5 = 1
Mon 04/15/13 12:27:19 DEBUG    NOTICE         0 Read and updated ini parameters. CurePass 6 = 0.  AltCurePass 6 = 0

DMC · Jun 10, 2013

So, the build plate never went qall the way to back of machine to pick-up the HMS? Or did it actually move? Yes or no to the actual physical movement?

Your encoder reader that reads the encoder strip may have has the wires rubbed and shorted-out?

Those wires are on bottom of the sled, and zip-tied. It is common for them to jiggle loose and start to rub.

It is either that, or still I say the encoder.

But first, answer my first question. It is a rare chance that the x-axis motor has issues, but I highly doubt that.
Very un-common.

rh3000 · Jun 10, 2013

The machine powers in HMS Recovery Error. The plate moves fine until it goes in the back to pick up the HMS tray. That's where it stops and gives Fatal Error. "Yes to Restart" and it does the same. (I moved the tray in the middle of the travel area by hand and the machine takes it back to HMS). So YES it does move, it takes it all the way back in the pickup position. I actually engaged the solenoid manually from remote to see if it is in location for pick up and it does pick it up with no problem.

I'll check the wires.

DMC · Jun 10, 2013

It is either the encoder strip, or the gizmo that actually reads the encoder then. (Wires are chaffed and intermittent short)

That's all it could be now. Probably the encoder strip if the wires are good.

Have you run an x-axis mapping yet? Do you want help to do it via teamviewer? 804-285-0777

If you have deviation value of over 8%, then it is certianly your encoder strip.

I run my printer without the front chamber door, to help vent some of that dust that accumulates all inside the printer.

5 yrs and never had to clean the strip.

Scotty

rh3000 · Jun 11, 2013

Success! We cleaned the contacts and ensured the plugs were held in tight. Ran the "Map Enc" a few times and it cleared the error. It printed a test print fine. I'm sending a part to print and see what does. It looks like she is back!!!
Thanks again for your help. Very much appreciated!

DMC · Jun 11, 2013

cleaned contacts of what?

plugs for what?

Anyway, good to hear it seems to be fixed (for now, LOL)

Have you tried the Crystal VisiJet material?

DMC · Jun 11, 2013

Oh, you run an x-axis mapping, then go into the log history and check out the results.

Mapping does nothing, but test the encoder reading. It does not recalibrate anything, or reset anything.

Just a measuring test. That's all.

rh3000 · Jun 12, 2013

*** said:
Oh, you run an x-axis mapping, then go into the log history and check out the results.

Mapping does nothing, but test the encoder reading. It does not recalibrate anything, or reset anything.

Just a measuring test. That's all.

Oh I know, I just ran x-axis mapping to take the table in and out a few times. It went in "Fatal Error", then "X-following Error", and then woke up fine, so the bad condition must have cleared, but I can't tell for sure what did it. We cleaned the encoder strip, moved the encoder wires around to make sure they don't touch, followed the wires and found the plug on the board to the left-rear side of the machine that had one prong was not all the way in. Used some generic contact cleaning spray in and put everything back together.

We printed some parts last night and the table seems to be working fine, but not all parts came right.
I am fighting some missing jets that gives me all kinds of scrap. I have the machine running on a slight angle (left to right),we learned that air bubbles enter the print head and cause missing jets, but it's not helping as much as we thought. Crappy cartridges from 3D Systems full of air?
Here is my last log

Cos

Code:

Tue 06/11/13 19:28:12 Exiting Application - Log Stopped
Tue 06/11/13 19:28:13 DEBUG    PARAM_CHANGE    0 Change Modeler Type: ProJet SD
Tue 06/11/13 19:28:13 DEBUG    PARAM_CHANGE    0 LoadBuildStyle: STANDARD FRACTAL
Tue 06/11/13 19:28:14 Log Started - ProJet SD 3000 1.06 Nov 21 2008 09:01:42
Tue 06/11/13 19:28:17 DEBUG    PARAM_CHANGE    0 Change Modeler Type: ProJet SD
Tue 06/11/13 19:28:17 DEBUG    PARAM_CHANGE    0 LoadBuildStyle: STANDARD FRACTAL
Tue 06/11/13 19:28:17 DEBUG    NOTICE         0 Computer: PROJET_41018
Tue 06/11/13 19:28:17 DEBUG    MACHINE_INI    0 Creation Time:    11/16/09 18:42:56
Tue 06/11/13 19:28:17 DEBUG    MACHINE_INI    0 Last Modify Time: 06/11/13 19:27:31
Tue 06/11/13 19:28:17 DEBUG    MACHINE_INI    0 Machine Hours: 28548.24
Tue 06/11/13 19:28:17 DEBUG    MACHINE_INI    0 Build Hours  : 879.89
Tue 06/11/13 19:28:17 DEBUG    MACHINE_INI    0 Lamp Hours   : 164.00
Tue 06/11/13 19:28:17 DEBUG    MACHINE_INI    0 Part Cartridges:    68
Tue 06/11/13 19:28:17 DEBUG    MACHINE_INI    0 Support Cartridges: 144
Tue 06/11/13 19:28:17 DEBUG    NOTICE         0 FPGA Combined Signature: 12
Tue 06/11/13 19:28:19 DEBUG    NOTICE         0 Material Control Type 2 board initialization version numbers:RFID: 021; Part: 023; Support 023
Tue 06/11/13 19:28:19 DEBUG    NOTICE         0 Clamp Feed System found installed **********************
Tue 06/11/13 19:28:19 DEBUG    NOTICE         0 Hi Res mode: 1
Tue 06/11/13 19:28:19 DEBUG    NORMALIZATION    5 Waveform: 5
Tue 06/11/13 19:28:19 DEBUG    NORMALIZATION    1 Support Group 1: 1
Tue 06/11/13 19:28:19 DEBUG    NORMALIZATION    2 Support Group 2: 2
Tue 06/11/13 19:28:19 DEBUG    NORMALIZATION    1 Support Group 3: 1
Tue 06/11/13 19:28:19 DEBUG    NORMALIZATION    2 Support Group 4: 2
Tue 06/11/13 19:28:19 DEBUG    NORMALIZATION    1 Support Group 5: 1
Tue 06/11/13 19:28:19 DEBUG    NORMALIZATION    2 Support Group 6: 2
Tue 06/11/13 19:28:19 DEBUG    NORMALIZATION    0 Support Group 7: 0
Tue 06/11/13 19:28:19 DEBUG    NORMALIZATION    1 Part Group 1: 1
Tue 06/11/13 19:28:19 DEBUG    NORMALIZATION    1 Part Group 2: 1
Tue 06/11/13 19:28:19 DEBUG    NORMALIZATION    1 Part Group 3: 1
Tue 06/11/13 19:28:19 DEBUG    NORMALIZATION    2 Part Group 4: 2
Tue 06/11/13 19:28:19 DEBUG    NORMALIZATION    1 Part Group 5: 1
Tue 06/11/13 19:28:19 DEBUG    NORMALIZATION    1 Part Group 6: 1
Tue 06/11/13 19:28:19 DEBUG    NORMALIZATION    0 Part Group 7: 0
Tue 06/11/13 19:28:20 DEBUG    NOTICE         0 Send Parameters To DSP
Tue 06/11/13 19:28:20 SUP_IDX  MS_INITIALIZE              0 Initialize D&K Support Feed System
Tue 06/11/13 19:28:20 PRT_IDX  MS_INITIALIZE              0 Initialize D&K Part Feed System
Tue 06/11/13 19:28:20 DEBUG    TEMP_STATE_CHANGE    4 Adapter Build
Tue 06/11/13 19:28:20 HMS      WIPE_INACTIVE    0
Tue 06/11/13 19:28:20 HMS_RCVR RECOVERY_INACTIVE            0
Tue 06/11/13 19:28:20 PREP     IDLE              0
Tue 06/11/13 19:28:20 DSP      LOG             0 Comm Channel Opened
Tue 06/11/13 19:28:20 DSP      LOG             0 SetResolutionMode : 1
Tue 06/11/13 19:28:20 DSP      LOG             0 Entering Main Command Loop
Tue 06/11/13 19:28:20 DEBUG    NOTICE         0 RmtDiag Listening on 192.168.10.207 port 22376
Tue 06/11/13 19:28:20 DSP      LOG             0 Servo Disabled by PC
Tue 06/11/13 19:28:21 DSP      LOG             0 SetResolutionMode : 1
Tue 06/11/13 19:28:21 DSP      LOG             0 Init Supp Indexer to  0.000000
Tue 06/11/13 19:28:21 DSP      LOG             0 Init Part Indexer to  0.000000
Tue 06/11/13 19:28:21 DEBUG    NOTICE         0 Listening on 192.168.10.207 port 22375
Tue 06/11/13 19:28:21 DSP      LOG             0 Init Supp Plunger to  1.176999
Tue 06/11/13 19:28:21 DSP      LOG             0 Init Part Plunger to  0.152000
Tue 06/11/13 19:28:21 DEBUG    NOTICE         0 UDP Socket on 192.168.10.207 port 22377
Tue 06/11/13 19:28:21 DEBUG    NOTICE         0 Diag2 Listening on 0.0.0.0 port 1047
Tue 06/11/13 19:28:21 DEBUG    NOTICE         0 Security Listening on 192.168.10.207 port 22378
Tue 06/11/13 19:28:21 DEBUG    NOTICE         0 UDP Security Socket on 192.168.10.207 port 22378
Tue 06/11/13 19:28:21 DEBUG    TEMP_STATE_CHANGE    5 Reservoir Build
Tue 06/11/13 19:28:21 SUP_IDX  IDLE                       0 Cartridges and plunger found in feed positions
Tue 06/11/13 19:28:21 PRT_IDX  IDLE                       0 Cartridges and plunger found in feed positions
Tue 06/11/13 19:28:21 DEBUG    TEMP_STATE_CHANGE    4 Adapter Build
Tue 06/11/13 19:28:21 DEBUG    TEMP_STATE_CHANGE    5 Reservoir Build
Tue 06/11/13 19:28:21 DSP      LOCAL_LOG       0 Found 3 Support cartridges. From 012
Tue 06/11/13 19:28:21 DEBUG    TEMP_STATE_CHANGE    6 Jetstack Delay; Delay: 10
Tue 06/11/13 19:28:21 DSP      LOCAL_LOG       0 Found 3 Part cartridges. From 012
Tue 06/11/13 19:28:21 DSP      LOCAL_LOG       0 Realtime GO_TO_BUILD
Tue 06/11/13 19:28:21 DSP      LOCAL_LOG       0 Machine Off Time Sets Delay
Tue 06/11/13 19:28:21 DSP      LOCAL_LOG       0 Jetstack Delay = 10 Minutes
Tue 06/11/13 19:28:27 DEBUG    NOTICE         0 MQG Bypass Enabled
Tue 06/11/13 19:28:27 SUPPORT  CHANGE_CARTRIDGE       0
Tue 06/11/13 19:28:27 PART     CHANGE_CARTRIDGE       0
Tue 06/11/13 19:28:27 DEBUG    PARAM_CHANGE    0 LoadBuildStyle: SD FRACTAL
Tue 06/11/13 19:28:28 BUILD    INITIALIZATION    0
Tue 06/11/13 19:28:28 BUILD    WAIT_READY      0
Tue 06/11/13 19:28:28 BUILD    PRE_JOB_CHECKS    0
Tue 06/11/13 19:28:31 DEBUG    NOTICE         0 Send Parameters To DSP
Tue 06/11/13 19:28:48 DIAG     USER_VALIDATED    0 RmtDiag: User ProJet_RH logged on from machine 192.168.10.207 port 1050
Tue 06/11/13 19:28:52 DEBUG    DIALOG_OPERATION    0 Stage Dialog Opened - SD FRACTAL
Tue 06/11/13 19:28:54 DEBUG    NOTICE         0 Send Parameters To DSP
Tue 06/11/13 19:28:54 DSP      LOG             0 Servo Enabled by PC
Tue 06/11/13 19:28:54 DSP      LOG             0 Home X
Tue 06/11/13 19:28:54 DSP      LOG             0 Detected X Limit
Tue 06/11/13 19:29:06 DSP      LOG             0 Encoder Points = 57838
Tue 06/11/13 19:29:06 DSP      LOG             0 Ave Time   1092.7 us
Tue 06/11/13 19:29:06 DSP      LOG             0 Min Time   1064.4 us Loc    1.1400 in
Tue 06/11/13 19:29:06 DSP      LOG             0 Max Time   1117.8 us Loc    8.6350 in
Tue 06/11/13 19:29:06 DSP      LOG             0 Variation    4.89 percent STDDEV=     5.0 us  0.46 percent
Tue 06/11/13 19:29:13 DSP      LOG             0 Encoder Points = 57838
Tue 06/11/13 19:29:13 DSP      LOG             0 Ave Time   1092.7 us
Tue 06/11/13 19:29:13 DSP      LOG             0 Min Time   1063.6 us Loc   25.1382 in
Tue 06/11/13 19:29:13 DSP      LOG             0 Max Time   1117.2 us Loc   14.4216 in
Tue 06/11/13 19:29:13 DSP      LOG             0 Variation    4.91 percent STDDEV=     5.0 us  0.46 percent
Tue 06/11/13 19:29:21 DSP      LOG             0 Encoder Points = 57838
Tue 06/11/13 19:29:21 DSP      LOG             0 Ave Time   1092.7 us
Tue 06/11/13 19:29:21 DSP      LOG             0 Min Time   1063.0 us Loc   25.1991 in
Tue 06/11/13 19:29:21 DSP      LOG             0 Max Time   1113.8 us Loc   14.4183 in
Tue 06/11/13 19:29:21 DSP      LOG             0 Variation    4.65 percent STDDEV=     5.0 us  0.46 percent
Tue 06/11/13 19:30:58 DSP      LOG             0 Encoder Points = 57838
Tue 06/11/13 19:30:58 DSP      LOG             0 Ave Time   1092.7 us
Tue 06/11/13 19:30:58 DSP      LOG             0 Min Time   1061.2 us Loc   25.1957 in
Tue 06/11/13 19:30:58 DSP      LOG             0 Max Time   1116.0 us Loc   10.4125 in
Tue 06/11/13 19:30:58 DSP      LOG             0 Variation    5.02 percent STDDEV=     5.0 us  0.46 percent
Tue 06/11/13 19:31:07 DSP      LOG             0 Encoder Points = 57838
Tue 06/11/13 19:31:07 DSP      LOG             0 Ave Time   1092.7 us
Tue 06/11/13 19:31:07 DSP      LOG             0 Min Time   1059.2 us Loc   25.1982 in
Tue 06/11/13 19:31:07 DSP      LOG             0 Max Time   1115.0 us Loc    8.7683 in
Tue 06/11/13 19:31:07 DSP      LOG             0 Variation    5.11 percent STDDEV=     5.0 us  0.46 percent
Tue 06/11/13 19:31:14 DSP      LOG             0 Encoder Points = 57838
Tue 06/11/13 19:31:14 DSP      LOG             0 Ave Time   1092.7 us
Tue 06/11/13 19:31:14 DSP      LOG             0 Min Time   1064.0 us Loc   25.1991 in
Tue 06/11/13 19:31:14 DSP      LOG             0 Max Time   1117.8 us Loc   10.4066 in
Tue 06/11/13 19:31:14 DSP      LOG             0 Variation    4.92 percent STDDEV=     5.0 us  0.46 percent
Tue 06/11/13 19:31:35 DEBUG    DIALOG_OPERATION    0 Stage Dialog Closed - SD FRACTAL
Tue 06/11/13 19:38:21 DEBUG    TEMP_STATE_CHANGE    7 Control Build; Delay: 10
Tue 06/11/13 19:38:55 DEBUG    TEMP_STATE_CHANGE    7 Control Build; Delay: 10
Tue 06/11/13 19:38:55 DSP      LOCAL_LOG       0 Realtime READY_TO_BUILD
Tue 06/11/13 19:38:55 DSP      LOG             0 Servo Enabled by PC
Tue 06/11/13 19:38:55 BUILD    HMS_ERROR_RECOVERY    0
Tue 06/11/13 19:38:56 HMS_RCVR RECOVERY_BEGIN               0
Tue 06/11/13 19:38:56 HMS_RCVR RECOVERY_MOVE_ZX             0 ServiceHmsRecovery Error State = 4
Tue 06/11/13 19:38:56 DSP      LOCAL_LOG       0 ServiceHmsRecovery Error State = 4; Move Z
Tue 06/11/13 19:38:56 DEBUG    DIALOG_OPERATION    0 Stage Dialog Opened - SD FRACTAL
Tue 06/11/13 19:39:16 HMS_RCVR RECOVERY_MOVE_XZ             0
Tue 06/11/13 19:39:16 DSP      LOCAL_LOG       0 ServiceHmsRecovery Error State = 4; Home X
Tue 06/11/13 19:39:16 DSP      LOG             0 Home X Back
Tue 06/11/13 19:39:38 HMS_RCVR RECOVERY_DISENGAGE_SOLENOID    0
Tue 06/11/13 19:39:40 HMS_RCVR RECOVERY_CHECK_SOLENOID_DISENGAGED    0
Tue 06/11/13 19:39:40 HMS_RCVR RECOVERY_HOME_XY             0
Tue 06/11/13 19:39:40 DSP      LOG             0 Home X
Tue 06/11/13 19:40:01 DSP      LOG             0 Detected X Limit
Tue 06/11/13 19:40:02 DSP      LOG             0 Home Y
Tue 06/11/13 19:40:10 DSP      LOG             0 Detected Y Limit
Tue 06/11/13 19:40:11 HMS_RCVR RECOVERY_HOME_Z              0
Tue 06/11/13 19:40:11 DSP      LOG             0 Home Z
Tue 06/11/13 19:41:17 DEBUG    NOTICE         0 Send Parameters To DSP
Tue 06/11/13 19:41:44 DSP      LOG             0 Z Right Limit Detected
Tue 06/11/13 19:41:44 DSP      LOG             0 Z Left Limit Detected
Tue 06/11/13 19:41:44 DEBUG    DIALOG_OPERATION    0 Stage Dialog Closed - SD FRACTAL
Tue 06/11/13 19:41:44 HMS_RCVR RECOVERY_RAISE_Z_STATE       0
Tue 06/11/13 19:41:44 DSP      LOG             0 Delta Z set to -0.015000
Tue 06/11/13 19:41:44 HMS_RCVR RECOVERY_WAIT_RAISE_Z_STATE    0
Tue 06/11/13 19:41:44 DSP      LOG             0 Raise Z
Tue 06/11/13 19:41:44 DSP      LOCAL_LOG       0 Recovery Raise Z
Tue 06/11/13 19:41:44 DEBUG    DIALOG_OPERATION    0 Stage Dialog Opened - SD FRACTAL
Tue 06/11/13 19:41:47 DEBUG    NOTICE         0 Send Parameters To DSP
Tue 06/11/13 19:43:13 DIAG     REMOTE_ERROR 10054 TCP Error: WSAECONNRESET in CDiagConnect::OnReceive()
Tue 06/11/13 19:43:13 DIAG     USER_VALIDATED    0 RmtDiag: User ProJet_RH logged on from machine 192.168.10.207 port 1053
Tue 06/11/13 19:43:13 DSP      LOG             0 Z Top Limit Detected
Tue 06/11/13 19:43:13 HMS_RCVR RECOVERY_SUCCESS_STATE       0
Tue 06/11/13 19:43:13 HMS      WIPE_INACTIVE    0 Recovery Success
Tue 06/11/13 19:43:13 HMS_RCVR RECOVERY_INACTIVE            0
Tue 06/11/13 19:43:13 BUILD    WAIT_READY      0
Tue 06/11/13 19:43:13 DSP      LOCAL_LOG       0 Recovery Success
Tue 06/11/13 19:43:13 DEBUG    TEMP_STATE_CHANGE    7 Control Build; Delay: 10
Tue 06/11/13 19:43:13 DSP      LOCAL_LOG       0 Realtime GO_TO_BUILD
Tue 06/11/13 19:43:13 DSP      LOCAL_LOG       0 Realtime READY_TO_BUILD
Tue 06/11/13 19:43:14 DSP      LOG             0 Servo Disabled by PC
Tue 06/11/13 19:43:51 DIAG     USER_VALIDATED    0 RmtDiag: User ProJet_RH logged on from machine 192.168.10.207 port 1058
Tue 06/11/13 19:44:00 DEBUG    DIALOG_OPERATION    0 Stage Dialog Opened - SD FRACTAL
Tue 06/11/13 19:44:11 DEBUG    DIALOG_OPERATION    0 Stage Dialog Closed - SD FRACTAL
Tue 06/11/13 19:44:25 DEBUG    DIALOG_OPERATION    0 Stage Dialog Opened - SD FRACTAL
Tue 06/11/13 19:44:27 DEBUG    NOTICE         0 Send Parameters To DSP
Tue 06/11/13 19:44:27 DSP      LOG             0 Servo Enabled by PC
Tue 06/11/13 19:44:27 DSP      LOG             0 Home X
Tue 06/11/13 19:44:27 DSP      LOG             0 Detected X Limit
Tue 06/11/13 19:44:34 DSP      LOG             0 Encoder Points = 57838
Tue 06/11/13 19:44:34 DSP      LOG             0 Ave Time   1092.7 us
Tue 06/11/13 19:44:34 DSP      LOG             0 Min Time   1064.8 us Loc    1.1467 in
Tue 06/11/13 19:44:34 DSP      LOG             0 Max Time   1117.6 us Loc    8.6491 in
Tue 06/11/13 19:44:34 DSP      LOG             0 Variation    4.83 percent STDDEV=     5.0 us  0.46 percent
Tue 06/11/13 19:44:42 DSP      LOG             0 Encoder Points = 57838
Tue 06/11/13 19:44:42 DSP      LOG             0 Ave Time   1092.7 us
Tue 06/11/13 19:44:42 DSP      LOG             0 Min Time   1066.0 us Loc   25.1991 in
Tue 06/11/13 19:44:42 DSP      LOG             0 Max Time   1114.8 us Loc    1.3600 in
Tue 06/11/13 19:44:42 DSP      LOG             0 Variation    4.47 percent STDDEV=     5.0 us  0.46 percent
Tue 06/11/13 19:44:52 DSP      LOG             0 Encoder Points = 57838
Tue 06/11/13 19:44:52 DSP      LOG             0 Ave Time   1092.7 us
Tue 06/11/13 19:44:52 DSP      LOG             0 Min Time   1061.6 us Loc   25.1991 in
Tue 06/11/13 19:44:52 DSP      LOG             0 Max Time   1117.8 us Loc    8.6558 in
Tue 06/11/13 19:44:52 DSP      LOG             0 Variation    5.14 percent STDDEV=     5.0 us  0.46 percent
Tue 06/11/13 19:44:56 DEBUG    DIALOG_OPERATION    0 Stage Dialog Closed - SD FRACTAL
Tue 06/11/13 19:49:15 DSP      LOG             0 X Following Error, Error Value = 0.100107 Encoder = 26.099894
Tue 06/11/13 19:49:16 BUILD    NON_BUILD_ERROR    1 X FOLLOWING ERROR
Tue 06/11/13 19:49:16 BUILD    NON_BUILD_ERROR_RECOVERY    1 X FOLLOWING ERROR
Tue 06/11/13 19:49:16 DEBUG    TEMP_STATE_CHANGE    4 Adapter Build
Tue 06/11/13 19:49:16 DEBUG    TEMP_STATE_CHANGE    5 Reservoir Build
Tue 06/11/13 19:49:16 DSP      LOG             0 Servo Enabled by PC
Tue 06/11/13 19:49:16 DSP      LOG             0 Home X
Tue 06/11/13 19:49:16 DEBUG    TEMP_STATE_CHANGE    6 Jetstack Delay; Delay: 10
Tue 06/11/13 19:49:16 DSP      LOCAL_LOG       0 Realtime GO_TO_BUILD
Tue 06/11/13 19:49:16 DSP      LOCAL_LOG       0 Machine Off Time Sets Delay
Tue 06/11/13 19:49:16 DSP      LOCAL_LOG       0 Jetstack Delay = 10 Minutes
Tue 06/11/13 19:49:16 DSP      LOG             0 X Limit NOT Detected
Tue 06/11/13 19:49:17 DSP      LOG             0 Home Y
Tue 06/11/13 19:49:36 BUILD    NON_BUILD_FATAL_ERROR   0
Tue 06/11/13 19:49:36 DEBUG    TEMP_STATE_CHANGE    3 Control Conserve
Tue 06/11/13 19:49:36 DSP      LOCAL_LOG       0 Realtime GO_TO_ERROR
Tue 06/11/13 19:49:36 DSP      LOCAL_LOG       0 Control Conserve Temperature
Tue 06/11/13 19:49:49 DEBUG    BTN_PRESSED   11 Yes Pressed
Tue 06/11/13 19:49:49 Exiting Application - Log Stopped
Tue 06/11/13 19:49:49 DEBUG    PARAM_CHANGE    0 Change Modeler Type: ProJet SD
Tue 06/11/13 19:49:49 DEBUG    PARAM_CHANGE    0 LoadBuildStyle: STANDARD FRACTAL
Tue 06/11/13 19:49:50 Log Started - ProJet SD 3000 1.06 Nov 21 2008 09:01:42
Tue 06/11/13 19:49:53 DEBUG    PARAM_CHANGE    0 Change Modeler Type: ProJet SD
Tue 06/11/13 19:49:53 DEBUG    PARAM_CHANGE    0 LoadBuildStyle: STANDARD FRACTAL
Tue 06/11/13 19:49:53 DEBUG    NOTICE         0 Computer: PROJET_41018
Tue 06/11/13 19:49:53 DEBUG    MACHINE_INI    0 Creation Time:    11/16/09 18:42:56
Tue 06/11/13 19:49:53 DEBUG    MACHINE_INI    0 Last Modify Time: 06/11/13 19:49:36
Tue 06/11/13 19:49:53 DEBUG    MACHINE_INI    0 Machine Hours: 28548.54
Tue 06/11/13 19:49:53 DEBUG    MACHINE_INI    0 Build Hours  : 879.89
Tue 06/11/13 19:49:53 DEBUG    MACHINE_INI    0 Lamp Hours   : 164.00
Tue 06/11/13 19:49:53 DEBUG    MACHINE_INI    0 Part Cartridges:    68
Tue 06/11/13 19:49:53 DEBUG    MACHINE_INI    0 Support Cartridges: 144
Tue 06/11/13 19:49:53 DEBUG    NOTICE         0 FPGA Combined Signature: 12
Tue 06/11/13 19:49:56 DEBUG    NOTICE         0 Material Control Type 2 board initialization version numbers:RFID: 021; Part: 023; Support 023
Tue 06/11/13 19:49:56 DEBUG    NOTICE         0 Clamp Feed System found installed **********************
Tue 06/11/13 19:49:56 DEBUG    NOTICE         0 Hi Res mode: 1
Tue 06/11/13 19:49:56 DEBUG    NORMALIZATION    5 Waveform: 5
Tue 06/11/13 19:49:56 DEBUG    NORMALIZATION    1 Support Group 1: 1
Tue 06/11/13 19:49:56 DEBUG    NORMALIZATION    2 Support Group 2: 2
Tue 06/11/13 19:49:56 DEBUG    NORMALIZATION    1 Support Group 3: 1
Tue 06/11/13 19:49:56 DEBUG    NORMALIZATION    2 Support Group 4: 2
Tue 06/11/13 19:49:56 DEBUG    NORMALIZATION    1 Support Group 5: 1
Tue 06/11/13 19:49:56 DEBUG    NORMALIZATION    2 Support Group 6: 2
Tue 06/11/13 19:49:56 DEBUG    NORMALIZATION    0 Support Group 7: 0
Tue 06/11/13 19:49:56 DEBUG    NORMALIZATION    1 Part Group 1: 1
Tue 06/11/13 19:49:56 DEBUG    NORMALIZATION    1 Part Group 2: 1
Tue 06/11/13 19:49:56 DEBUG    NORMALIZATION    1 Part Group 3: 1
Tue 06/11/13 19:49:56 DEBUG    NORMALIZATION    2 Part Group 4: 2
Tue 06/11/13 19:49:56 DEBUG    NORMALIZATION    1 Part Group 5: 1
Tue 06/11/13 19:49:56 DEBUG    NORMALIZATION    1 Part Group 6: 1
Tue 06/11/13 19:49:56 DEBUG    NORMALIZATION    0 Part Group 7: 0
Tue 06/11/13 19:49:56 DEBUG    NOTICE         0 Send Parameters To DSP
Tue 06/11/13 19:49:56 SUP_IDX  MS_INITIALIZE              0 Initialize D&K Support Feed System
Tue 06/11/13 19:49:56 PRT_IDX  MS_INITIALIZE              0 Initialize D&K Part Feed System
Tue 06/11/13 19:49:56 DEBUG    TEMP_STATE_CHANGE    4 Adapter Build
Tue 06/11/13 19:49:56 HMS      WIPE_INACTIVE    0
Tue 06/11/13 19:49:56 HMS_RCVR RECOVERY_INACTIVE            0
Tue 06/11/13 19:49:57 PREP     IDLE              0
Tue 06/11/13 19:49:57 DSP      LOG             0 Comm Channel Opened
Tue 06/11/13 19:49:57 DSP      LOG             0 SetResolutionMode : 1
Tue 06/11/13 19:49:57 DSP      LOG             0 Entering Main Command Loop
Tue 06/11/13 19:49:57 DEBUG    NOTICE         0 RmtDiag Listening on 192.168.10.207 port 22376
Tue 06/11/13 19:49:57 DSP      LOG             0 Servo Disabled by PC
Tue 06/11/13 19:49:57 DSP      LOG             0 SetResolutionMode : 1
Tue 06/11/13 19:49:57 DSP      LOG             0 Init Supp Indexer to  0.000000
Tue 06/11/13 19:49:57 DEBUG    NOTICE         0 Listening on 192.168.10.207 port 22375
Tue 06/11/13 19:49:57 DSP      LOG             0 Init Part Indexer to  0.000000
Tue 06/11/13 19:49:57 DSP      LOG             0 Init Supp Plunger to  1.176999
Tue 06/11/13 19:49:57 DSP      LOG             0 Init Part Plunger to  0.152000
Tue 06/11/13 19:49:57 DEBUG    NOTICE         0 UDP Socket on 192.168.10.207 port 22377
Tue 06/11/13 19:49:57 DEBUG    NOTICE         0 Diag2 Listening on 0.0.0.0 port 1061
Tue 06/11/13 19:49:57 DEBUG    NOTICE         0 Security Listening on 192.168.10.207 port 22378
Tue 06/11/13 19:49:57 DEBUG    NOTICE         0 UDP Security Socket on 192.168.10.207 port 22378
Tue 06/11/13 19:49:57 DEBUG    TEMP_STATE_CHANGE    5 Reservoir Build
Tue 06/11/13 19:49:57 SUP_IDX  IDLE                       0 Cartridges and plunger found in feed positions
Tue 06/11/13 19:49:57 PRT_IDX  IDLE                       0 Cartridges and plunger found in feed positions
Tue 06/11/13 19:49:57 DEBUG    TEMP_STATE_CHANGE    4 Adapter Build
Tue 06/11/13 19:49:57 DEBUG    TEMP_STATE_CHANGE    5 Reservoir Build
Tue 06/11/13 19:49:57 DSP      LOCAL_LOG       0 Found 3 Support cartridges. From 012
Tue 06/11/13 19:49:57 DEBUG    TEMP_STATE_CHANGE    6 Jetstack Delay; Delay: 10
Tue 06/11/13 19:49:57 DSP      LOCAL_LOG       0 Found 3 Part cartridges. From 012
Tue 06/11/13 19:49:57 DSP      LOCAL_LOG       0 Realtime GO_TO_BUILD
Tue 06/11/13 19:49:57 DSP      LOCAL_LOG       0 Machine Off Time Sets Delay
Tue 06/11/13 19:49:57 DSP      LOCAL_LOG       0 Jetstack Delay = 10 Minutes
Tue 06/11/13 19:50:03 DEBUG    NOTICE         0 MQG Bypass Enabled
Tue 06/11/13 19:50:04 SUPPORT  CHANGE_CARTRIDGE       0
Tue 06/11/13 19:50:04 PART     CHANGE_CARTRIDGE       0
Tue 06/11/13 19:50:04 DEBUG    PARAM_CHANGE    0 LoadBuildStyle: SD FRACTAL
Tue 06/11/13 19:50:04 BUILD    INITIALIZATION    0
Tue 06/11/13 19:50:04 BUILD    WAIT_READY      0
Tue 06/11/13 19:50:05 DSP      LOG             0 Servo Disabled by PC
Tue 06/11/13 19:50:27 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:50:27 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:50:28 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:50:28 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:50:28 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:50:29 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:50:30 DIAG     BTN_PRESSED    14 Diagnostics Button Pressed
Tue 06/11/13 19:50:30 DIAG     BTN_PRESSED    14 Diagnostics Button Pressed
Tue 06/11/13 19:50:30 DIAG     BTN_PRESSED    14 Diagnostics Button Pressed
Tue 06/11/13 19:50:30 DIAG     BTN_PRESSED    14 Diagnostics Button Pressed
Tue 06/11/13 19:50:31 DIAG     BTN_PRESSED    14 Diagnostics Button Pressed
Tue 06/11/13 19:50:32 DIAG     BTN_PRESSED    14 Diagnostics Button Pressed
Tue 06/11/13 19:50:33 DIAG     BTN_PRESSED    13 Diagnostics Button Pressed
Tue 06/11/13 19:50:36 DEBUG    BTN_PRESSED   13 No Pressed
Tue 06/11/13 19:50:39 DEBUG    BTN_PRESSED   13 No Pressed
Tue 06/11/13 19:50:41 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:50:41 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:50:41 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:50:41 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:50:42 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:50:42 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:50:42 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:50:43 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:50:45 DIAG     BTN_PRESSED     1 Diagnostics Button Pressed
Tue 06/11/13 19:50:55 DIAG     BTN_PRESSED     1 Diagnostics Button Pressed
Tue 06/11/13 19:51:02 DIAG     BTN_PRESSED    11 Diagnostics Button Pressed
Tue 06/11/13 19:51:02 DEBUG    BTN_PRESSED    3 Test Pressed
Tue 06/11/13 19:51:02 BUILD    PRE_JOB_CHECKS    0
Tue 06/11/13 19:51:04 DEBUG    BTN_PRESSED   11 Yes Pressed
Tue 06/11/13 19:51:06 DEBUG    NOTICE         0 Send Parameters To DSP
Tue 06/11/13 19:53:19 DIAG     USER_VALIDATED    0 RmtDiag: User ProJet_RH logged on from machine 192.168.10.207 port 1066
Tue 06/11/13 19:53:26 DEBUG    DIALOG_OPERATION    0 Stage Dialog Opened - SD FRACTAL
Tue 06/11/13 19:53:38 DSP      LOG             0 Servo Enabled by PC
Tue 06/11/13 19:53:59 DEBUG    NOTICE         0 Send Parameters To DSP
Tue 06/11/13 19:53:59 DSP      LOG             0 Servo Enabled by PC
Tue 06/11/13 19:53:59 DSP      LOG             0 Home X
Tue 06/11/13 19:54:00 DSP      LOG             0 Detected X Limit
Tue 06/11/13 19:54:16 DSP      LOG             0 Encoder Points = 57838
Tue 06/11/13 19:54:16 DSP      LOG             0 Ave Time   1092.7 us
Tue 06/11/13 19:54:16 DSP      LOG             0 Min Time   1060.8 us Loc   25.1991 in
Tue 06/11/13 19:54:16 DSP      LOG             0 Max Time   1116.4 us Loc    1.3633 in
Tue 06/11/13 19:54:16 DSP      LOG             0 Variation    5.09 percent STDDEV=     5.0 us  0.46 percent
Tue 06/11/13 19:54:23 DSP      LOG             0 Encoder Points = 57838
Tue 06/11/13 19:54:23 DSP      LOG             0 Ave Time   1092.7 us
Tue 06/11/13 19:54:23 DSP      LOG             0 Min Time   1065.4 us Loc   25.1991 in
Tue 06/11/13 19:54:23 DSP      LOG             0 Max Time   1115.4 us Loc    1.3642 in
Tue 06/11/13 19:54:23 DSP      LOG             0 Variation    4.58 percent STDDEV=     5.0 us  0.46 percent
Tue 06/11/13 19:54:34 DSP      LOG             0 Encoder Points = 57838
Tue 06/11/13 19:54:34 DSP      LOG             0 Ave Time   1092.7 us
Tue 06/11/13 19:54:34 DSP      LOG             0 Min Time   1065.2 us Loc    1.1392 in
Tue 06/11/13 19:54:34 DSP      LOG             0 Max Time   1115.6 us Loc    3.7042 in
Tue 06/11/13 19:54:34 DSP      LOG             0 Variation    4.61 percent STDDEV=     5.0 us  0.46 percent
Tue 06/11/13 19:54:38 DEBUG    DIALOG_OPERATION    0 Stage Dialog Closed - SD FRACTAL
Tue 06/11/13 19:54:59 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:54:59 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:00 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:00 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:00 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:00 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:01 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:03 DIAG     BTN_PRESSED    14 Diagnostics Button Pressed
Tue 06/11/13 19:55:04 DIAG     BTN_PRESSED    14 Diagnostics Button Pressed
Tue 06/11/13 19:55:04 DIAG     BTN_PRESSED    14 Diagnostics Button Pressed
Tue 06/11/13 19:55:04 DIAG     BTN_PRESSED    14 Diagnostics Button Pressed
Tue 06/11/13 19:55:05 DIAG     BTN_PRESSED    14 Diagnostics Button Pressed
Tue 06/11/13 19:55:05 DIAG     BTN_PRESSED    14 Diagnostics Button Pressed
Tue 06/11/13 19:55:06 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:07 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:07 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:07 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:07 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:08 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:08 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:09 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:10 DIAG     BTN_PRESSED    13 Diagnostics Button Pressed
Tue 06/11/13 19:55:13 DEBUG    BTN_PRESSED    1 Online Pressed
Tue 06/11/13 19:55:19 DEBUG    BTN_PRESSED    1 Online Pressed
Tue 06/11/13 19:55:25 DIAG     USER_VALIDATED    0 RmtDiag: User ProJet_RH logged on from machine 192.168.10.207 port 1070
Tue 06/11/13 19:55:31 DEBUG    BTN_PRESSED    7 Abort Pressed
Tue 06/11/13 19:55:31 BUILD    WAIT_READY      0
Tue 06/11/13 19:55:31 DSP      LOG             0 Servo Disabled by PC
Tue 06/11/13 19:55:36 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:37 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:37 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:37 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:37 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:37 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:38 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:39 DIAG     BTN_PRESSED    15 Diagnostics Button Pressed
Tue 06/11/13 19:55:40 DIAG     BTN_PRESSED    11 Diagnostics Button Pressed
Tue 06/11/13 19:55:40 DEBUG    BTN_PRESSED    3 Test Pressed
Tue 06/11/13 19:55:40 BUILD    PRE_JOB_CHECKS    0
Tue 06/11/13 19:55:42 DEBUG    BTN_PRESSED   11 Yes Pressed
Tue 06/11/13 19:55:44 DEBUG    NOTICE         0 Send Parameters To DSP
Tue 06/11/13 19:59:57 DEBUG    TEMP_STATE_CHANGE    7 Control Build; Delay: 10
Tue 06/11/13 20:00:30 DEBUG    TEMP_STATE_CHANGE    7 Control Build; Delay: 10
Tue 06/11/13 20:00:30 DSP      LOG             0 Servo Enabled by PC
Tue 06/11/13 20:00:30 DSP      LOCAL_LOG       0 Realtime READY_TO_BUILD
Tue 06/11/13 20:00:30 BUILD    HOME_XY         0
Tue 06/11/13 20:00:31 DSP      LOG             0 Home X
Tue 06/11/13 20:00:31 DSP      LOG             0 Detected X Limit
Tue 06/11/13 20:00:31 DSP      LOG             0 Home Y
Tue 06/11/13 20:00:32 DSP      LOG             0 Detected Y Limit
Tue 06/11/13 20:00:33 BUILD    HOME_Z          0
Tue 06/11/13 20:00:33 DSP      LOG             0 Home Z
Tue 06/11/13 20:02:05 DSP      LOG             0 Z Right Limit Detected
Tue 06/11/13 20:02:05 DSP      LOG             0 Z Left Limit Detected
Tue 06/11/13 20:02:06 BUILD    HEAD_CLEANING    0
Tue 06/11/13 20:02:06 DSP      LOG             0 Delta Z set to -0.015000
Tue 06/11/13 20:02:06 HMS      WIPE_INITIATE    0 Materials Present - Head Cleaning Initiated
Tue 06/11/13 20:02:06 HMS      WIPE_MOVE_Z_TO_PICKUP    0 Beginning Printhead Maintenance
Tue 06/11/13 20:02:52 HMS      WIPE_CYCLE_START_STATE    0
Tue 06/11/13 20:03:07 HMS      WIPE_WAIT_PURGE    0
Tue 06/11/13 20:03:07 DSP      LOCAL_LOG       0 Start Printhead Purge
Tue 06/11/13 20:03:16 DSP      LOCAL_LOG       0 Support Pump Pos=1.177; Vacuum=0.003; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=70 sec; MPixels/Sec=0.000000
Tue 06/11/13 20:03:18 DSP      LOCAL_LOG       0 Support Pump Pos=1.202; Vacuum=0.003; Cnt=2
Tue 06/11/13 20:03:21 DSP      LOCAL_LOG       0 Support Pump Pos=1.227; Vacuum=0.003; Cnt=3
Tue 06/11/13 20:03:24 HMS      WIPE_WAIT_DRIP_STOP    0
Tue 06/11/13 20:03:24 DSP      LOCAL_LOG       0 Support Pump Pos=1.252; Vacuum=0.003; Cnt=4
Tue 06/11/13 20:03:24 DSP      LOCAL_LOG       0 End Printhead Purge
Tue 06/11/13 20:03:26 DSP      LOCAL_LOG       0 Support Pump Pos=1.277; Vacuum=0.003; Cnt=5
Tue 06/11/13 20:03:29 HMS      WIPE_START_STATE    0 Wipe Start: 1/7
Tue 06/11/13 20:03:29 DSP      LOCAL_LOG       0 Support Pump Pos=1.302; Vacuum=0.003; Cnt=6
Tue 06/11/13 20:03:32 DSP      LOCAL_LOG       0 Support Pump Pos=1.327; Vacuum=0.003; Cnt=7
Tue 06/11/13 20:03:35 DSP      LOCAL_LOG       0 Support Pump Pos=1.352; Vacuum=0.003; Cnt=8
Tue 06/11/13 20:03:37 DSP      LOCAL_LOG       0 Support Pump Pos=1.377; Vacuum=0.101; Cnt=9
Tue 06/11/13 20:03:40 DSP      LOCAL_LOG       0 Support Pump Pos=1.402; Vacuum=0.448; Cnt=10
Tue 06/11/13 20:03:43 DSP      LOCAL_LOG       0 Support Pump Pos=1.427; Vacuum=0.879; Cnt=11
Tue 06/11/13 20:03:45 DSP      LOCAL_LOG       0 Support Pump Pos=1.452; Vacuum=1.361; Cnt=12
Tue 06/11/13 20:03:48 DSP      LOCAL_LOG       0 Support Pump Pos=1.477; Vacuum=1.831; Cnt=13
Tue 06/11/13 20:03:50 DSP      LOCAL_LOG       0 Support Pump Pos=1.502; Vacuum=2.279; Cnt=14
Tue 06/11/13 20:03:53 DSP      LOCAL_LOG       0 Support Pump Pos=1.527; Vacuum=2.766; Cnt=15
Tue 06/11/13 20:03:56 DSP      LOCAL_LOG       0 Support Pump Pos=1.552; Vacuum=3.245; Cnt=16
Tue 06/11/13 20:03:58 DSP      LOCAL_LOG       0 Support Pump Pos=1.577; Vacuum=3.727; Cnt=17
Tue 06/11/13 20:04:01 DSP      LOCAL_LOG       0 Support Pump Pos=1.602; Vacuum=4.214; Cnt=18
Tue 06/11/13 20:04:04 DSP      LOCAL_LOG       0 Support Pump Pos=1.627; Vacuum=4.656; Cnt=19
Tue 06/11/13 20:04:06 DSP      LOCAL_LOG       0 Support Pump Pos=1.652; Vacuum=4.589; Cnt=20
Tue 06/11/13 20:04:09 DSP      LOCAL_LOG       0 Support Pump Pos=1.677; Vacuum=4.634; Cnt=21
Tue 06/11/13 20:04:12 DSP      LOCAL_LOG       0 Support Pump Pos=1.702; Vacuum=4.642; Cnt=22
Tue 06/11/13 20:04:15 DSP      LOCAL_LOG       0 Support Pump Pos=1.727; Vacuum=4.606; Cnt=23
Tue 06/11/13 20:04:17 DSP      LOCAL_LOG       0 Support Pump Pos=1.752; Vacuum=4.640; Cnt=24
Tue 06/11/13 20:04:20 DSP      LOCAL_LOG       0 Support Pump Pos=1.777; Vacuum=4.612; Cnt=25
Tue 06/11/13 20:04:23 DSP      LOCAL_LOG       0 Support Pump Pos=1.802; Vacuum=4.631; Cnt=26
Tue 06/11/13 20:04:25 DSP      LOCAL_LOG       0 Support Pump Pos=1.827; Vacuum=4.617; Cnt=27
Tue 06/11/13 20:04:28 DSP      LOCAL_LOG       0 Support Pump Pos=1.852; Vacuum=4.606; Cnt=28
Tue 06/11/13 20:04:30 DSP      LOCAL_LOG       0 Support Pump Pos=1.877; Vacuum=4.598; Cnt=29
Tue 06/11/13 20:04:33 DSP      LOCAL_LOG       0 Support Pump Pos=1.902; Vacuum=4.634; Cnt=30
Tue 06/11/13 20:04:36 DSP      LOCAL_LOG       0 Support Pump Pos=1.927; Vacuum=4.612; Cnt=31
Tue 06/11/13 20:04:38 DSP      LOCAL_LOG       0 Support Pump Pos=1.952; Vacuum=4.598; Cnt=32
Tue 06/11/13 20:04:41 DSP      LOCAL_LOG       0 Support Pump Pos=1.977; Vacuum=4.598; Cnt=33
Tue 06/11/13 20:04:44 DSP      LOCAL_LOG       0 Support Pump Pos=2.002; Vacuum=4.659; Cnt=34
Tue 06/11/13 20:04:46 DSP      LOCAL_LOG       0 Support Pump Pos=2.027; Vacuum=4.645; Cnt=35
Tue 06/11/13 20:04:49 DSP      LOCAL_LOG       0 Support Pump Pos=2.052; Vacuum=4.640; Cnt=36
Tue 06/11/13 20:04:52 DSP      LOCAL_LOG       0 Support Pump Pos=2.077; Vacuum=4.665; Cnt=37
Tue 06/11/13 20:04:54 DSP      LOCAL_LOG       0 Support Pump Pos=2.102; Vacuum=4.626; Cnt=38
Tue 06/11/13 20:04:57 DSP      LOCAL_LOG       0 Support Pump Pos=2.127; Vacuum=4.609; Cnt=39
Tue 06/11/13 20:04:58 HMS      WIPE_START_STATE    0 Wipe Start: 2/7
Tue 06/11/13 20:05:00 DSP      LOCAL_LOG       0 Support Pump Pos=2.152; Vacuum=4.620; Cnt=40
Tue 06/11/13 20:05:02 DSP      LOCAL_LOG       0 Support Pump Pos=2.177; Vacuum=4.603; Cnt=41
Tue 06/11/13 20:05:05 DSP      LOCAL_LOG       0 Support Pump Pos=2.202; Vacuum=4.575; Cnt=42
Tue 06/11/13 20:05:08 DSP      LOCAL_LOG       0 Support Pump Pos=2.227; Vacuum=4.578; Cnt=43
Tue 06/11/13 20:05:10 DSP      LOCAL_LOG       0 Support Pump Pos=2.252; Vacuum=4.592; Cnt=44
Tue 06/11/13 20:05:13 DSP      LOCAL_LOG       0 Support Pump Pos=2.277; Vacuum=4.631; Cnt=45
Tue 06/11/13 20:05:16 DSP      LOCAL_LOG       0 Support Pump Pos=2.302; Vacuum=4.645; Cnt=46
Tue 06/11/13 20:05:18 DSP      LOCAL_LOG       0 Support Pump Pos=2.327; Vacuum=4.617; Cnt=47
Tue 06/11/13 20:05:21 DSP      LOCAL_LOG       0 Support Pump Pos=2.352; Vacuum=4.612; Cnt=48
Tue 06/11/13 20:05:24 DSP      LOCAL_LOG       0 Support Pump Pos=2.377; Vacuum=4.570; Cnt=49
Tue 06/11/13 20:05:26 DSP      LOCAL_LOG       0 Support Pump Pos=2.402; Vacuum=4.614; Cnt=50
Tue 06/11/13 20:05:29 DEBUG    NOTICE         0 bIndex1Required Set because of too many pumps
Tue 06/11/13 20:05:29 SUP_IDX  MS_START_CHANGE            0 bIndexRequired Detected
Tue 06/11/13 20:05:29 SUPPORT  DETECT_CARTRIDGE       0 from Clamp Feed system
Tue 06/11/13 20:05:29 SUP_IDX  MS_WAIT_DETECT_CARTRIDGE    0 wait for the Cartridge RFID to be read
Tue 06/11/13 20:05:30 DEBUG    ERROR          0 Rfid ValidateResponse error: NO_TAG_FOUND
Tue 06/11/13 20:05:30 SUPPORT  CARTRIDGE_AVAILABLE    0 Cartridge Not Detected; Id=0x0; Type=; Batch: 01/01/70; Exp Date: 01/01/70; Machine Used On: 0; Used Date: 0
Tue 06/11/13 20:05:30 SUPPORT  WRITE_CARTRIDGE        0 from Clamp Feed system
Tue 06/11/13 20:05:30 SUP_IDX  WAIT_WRITE_CARTRIDGE       2 Cartridge Not Detected: Id=0x0
Tue 06/11/13 20:05:30 DEBUG    ERROR          0 Rfid ValidateResponse error: NO_TAG_FOUND
Tue 06/11/13 20:05:31 SUPPORT  CHANGE_CARTRIDGE       0
Tue 06/11/13 20:05:31 SUP_IDX  MS_DUMP                    0
Tue 06/11/13 20:05:31 SUP_IDX  MS_PLUNGER_RETRACT         0 Wait for plunger to disengage
Tue 06/11/13 20:05:31 DSP      LOCAL_LOG       0 Time Last Support Cartridge Ejected: 106:22:5 D:H:M
Tue 06/11/13 20:05:42 HMS      WIPE_START_STATE    0 Wipe Start: 3/7
Tue 06/11/13 20:06:00 SUP_IDX  MS_RIGHT_DUMP              0 Wait for right clamp load
Tue 06/11/13 20:06:07 SUP_IDX  MS_LEFT_DUMP               0 Wait for left clamp to open
Tue 06/11/13 20:06:21 DSP      LOCAL_LOG       0 Found 2 Support cartridges. From 12
Tue 06/11/13 20:06:22 SUP_IDX  MS_LEFT_DUMP_DELAY         0 Delay for cartridge to dump
Tue 06/11/13 20:06:22 SUP_IDX  MS_RIGHT_DUMP_2            0 Wait for right clamp closed
Tue 06/11/13 20:06:25 HMS      WIPE_START_STATE    0 Wipe Start: 4/7
Tue 06/11/13 20:06:31 SUP_IDX  MS_LEFT_DUMP_FINISH        0 Wait for left clamp to load
Tue 06/11/13 20:06:37 SUP_IDX  MS_LOAD_FEED               0
Tue 06/11/13 20:06:37 SUP_IDX  MS_RIGHT_LOAD              0 Wait for right clamp open
Tue 06/11/13 20:06:37 DSP      LOCAL_LOG       0 Ok to open inner support clamp
Tue 06/11/13 20:06:50 SUP_IDX  MS_RIGHT_LOAD_DELAY        0 Wait for the cartridge to drop into the feed position
Tue 06/11/13 20:06:53 DSP      LOCAL_LOG       0 Found 2 Support cartridges. From 02
Tue 06/11/13 20:06:55 SUP_IDX  MS_PREPARE_FOR_HOLD        0 Move clamps to the hold position
Tue 06/11/13 20:06:55 SUP_IDX  MS_LEFT_HOLD               0 Wait for left clamp closed
Tue 06/11/13 20:07:04 SUP_IDX  MS_RIGHT_HOLD              0 Wait for right clamp closed
Tue 06/11/13 20:07:09 HMS      WIPE_START_STATE    0 Wipe Start: 5/7
Tue 06/11/13 20:07:18 SUP_IDX  MS_PLUNGER_MOVE            1 Test for plunger moving forward
Tue 06/11/13 20:07:18 DSP      LOCAL_LOG       0 Set FeedMeltTime = 0
Tue 06/11/13 20:07:25 SUP_IDX  MS_WAIT_CLAMPS_TIGHT       0 Wait for clamps to close tight
Tue 06/11/13 20:07:25 DSP      LOCAL_LOG       0 Inner support clamp no longer open
Tue 06/11/13 20:07:29 SUP_IDX  MS_ENGAGE_JOG_RIGHT        0 Wait for right clamp to open slightly
Tue 06/11/13 20:07:33 SUP_IDX  MS_ENGAGE_JOG_LEFT         0 Wait for left clamp to open slightly
Tue 06/11/13 20:07:37 SUP_IDX  MS_PLUNGER_HOLD            0 Send the plunger to the holding position
Tue 06/11/13 20:07:53 HMS      WIPE_START_STATE    0 Wipe Start: 6/7
Tue 06/11/13 20:08:13 SUP_IDX  MS_LOAD_PREHEAT            0 Load Preheat position
Tue 06/11/13 20:08:13 SUP_IDX  MS_LEFT_PREHEAT            0 Wait for right clamp load
Tue 06/11/13 20:08:21 SUP_IDX  MS_RIGHT_PREHEAT           0 Wait for left clamp open
Tue 06/11/13 20:08:36 SUP_IDX  MS_RIGHT_PREHEAT_DELAY     0 Delay for cartridge drop into preheat
Tue 06/11/13 20:08:36 HMS      WIPE_START_STATE    0 Wipe Start: 7/7
Tue 06/11/13 20:08:41 DSP      LOCAL_LOG       0 Found 2 Support cartridges. From 01
Tue 06/11/13 20:08:41 SUP_IDX  MS_RIGHT_PREHEAT_2         0 Wait for right clamp closed
Tue 06/11/13 20:08:50 SUP_IDX  MS_LEFT_PREHEAT_2          0 Wait for left clamp closed
Tue 06/11/13 20:09:05 SUP_IDX  MS_CHANGE_DONE             0
Tue 06/11/13 20:09:05 DSP      LOCAL_LOG       0 Set PreheatMeltTime = 0
Tue 06/11/13 20:09:05 DSP      LOCAL_LOG       0 Set Preheat2MeltTime = 5400
Tue 06/11/13 20:09:05 SUP_IDX  IDLE                       1 Wait for another change cartridge request
Tue 06/11/13 20:09:19 HMS      WIPE_WAIT_GROUP_FIRE    0 Wipe Fire
Tue 06/11/13 20:09:20 DSP      LOG             0 Sending Normalization
Tue 06/11/13 20:09:32 DSP      LOG             0 Test Fire 90000 times at 24.00 kHz
Tue 06/11/13 20:09:32 DSP      LOG             0 Test Reg = D181 2181
Tue 06/11/13 20:09:41 HMS      WIPE_X_AT_DUMP_STATE    0 Wipe At Dump
Tue 06/11/13 20:10:54 HMS      WIPE_WAIT_DRIP_STOP_2    0
Tue 06/11/13 20:11:10 HMS      WIPE_WAIT_Z_PICKUP_2    0
Tue 06/11/13 20:11:36 HMS      WIPE_CYCLE_START_STATE    0
Tue 06/11/13 20:11:48 HMS      WIPE_WAIT_PURGE    0
Tue 06/11/13 20:11:48 DSP      LOCAL_LOG       0 Start Printhead Purge
Tue 06/11/13 20:11:55 DSP      LOCAL_LOG       0 Part Pump Pos=0.152; Vacuum=0.003; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=589 sec; MPixels/Sec=0.000000
Tue 06/11/13 20:11:58 DSP      LOCAL_LOG       0 Part Pump Pos=0.177; Vacuum=0.003; Cnt=2
Tue 06/11/13 20:11:59 DSP      LOCAL_LOG       0 Preheat 2 cartridge detected, set Preheat2MeltTime = 5400
Tue 06/11/13 20:12:00 DSP      LOCAL_LOG       0 Support Pump Pos=0.002; Vacuum=0.003; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=524 sec; MPixels/Sec=0.000000
Tue 06/11/13 20:12:01 DSP      LOCAL_LOG       0 Found 3 Support cartridges. From 012
Tue 06/11/13 20:12:02 DSP      LOCAL_LOG       0 Part Pump Pos=0.202; Vacuum=0.003; Cnt=3
Tue 06/11/13 20:12:04 HMS      WIPE_WAIT_DRIP_STOP    0
Tue 06/11/13 20:12:04 DSP      LOCAL_LOG       0 End Printhead Purge
Tue 06/11/13 20:12:05 DSP      LOCAL_LOG       0 Support Pump Pos=0.027; Vacuum=0.003; Cnt=2
Tue 06/11/13 20:12:07 DSP      LOCAL_LOG       0 Part Pump Pos=0.227; Vacuum=0.003; Cnt=4
Tue 06/11/13 20:12:09 HMS      WIPE_START_STATE    0 Wipe Start: 1/7
Tue 06/11/13 20:12:10 DSP      LOCAL_LOG       0 Part Pump Pos=0.252; Vacuum=0.003; Cnt=5
Tue 06/11/13 20:12:12 DSP      LOCAL_LOG       0 Part Pump Pos=0.277; Vacuum=0.048; Cnt=6
Tue 06/11/13 20:12:15 DSP      LOCAL_LOG       0 Part Pump Pos=0.302; Vacuum=1.226; Cnt=7
Tue 06/11/13 20:12:18 DSP      LOCAL_LOG       0 Part Pump Pos=0.327; Vacuum=2.472; Cnt=8
Tue 06/11/13 20:12:20 DSP      LOCAL_LOG       0 Part Pump Pos=0.352; Vacuum=3.769; Cnt=9
Tue 06/11/13 20:12:23 DSP      LOCAL_LOG       0 Part Pump Pos=0.377; Vacuum=4.640; Cnt=10
Tue 06/11/13 20:12:26 DSP      LOCAL_LOG       0 Part Pump Pos=0.402; Vacuum=4.612; Cnt=11
Tue 06/11/13 20:12:28 DSP      LOCAL_LOG       0 Part Pump Pos=0.427; Vacuum=4.659; Cnt=12
Tue 06/11/13 20:12:31 DSP      LOCAL_LOG       0 Part Pump Pos=0.452; Vacuum=4.623; Cnt=13
Tue 06/11/13 20:12:34 DSP      LOCAL_LOG       0 Part Pump Pos=0.477; Vacuum=4.606; Cnt=14
Tue 06/11/13 20:12:36 DSP      LOCAL_LOG       0 Part Pump Pos=0.502; Vacuum=4.592; Cnt=15
Tue 06/11/13 20:12:39 DSP      LOCAL_LOG       0 Part Pump Pos=0.527; Vacuum=4.637; Cnt=16
Tue 06/11/13 20:12:42 DSP      LOCAL_LOG       0 Part Pump Pos=0.552; Vacuum=4.564; Cnt=17
Tue 06/11/13 20:12:44 DSP      LOCAL_LOG       0 Part Pump Pos=0.577; Vacuum=4.589; Cnt=18
Tue 06/11/13 20:12:47 DSP      LOCAL_LOG       0 Part Pump Pos=0.602; Vacuum=4.600; Cnt=19
Tue 06/11/13 20:12:50 DSP      LOCAL_LOG       0 Part Pump Pos=0.627; Vacuum=4.589; Cnt=20
Tue 06/11/13 20:12:52 DSP      LOCAL_LOG       0 Part Pump Pos=0.652; Vacuum=4.572; Cnt=21
Tue 06/11/13 20:12:55 DSP      LOCAL_LOG       0 Part Pump Pos=0.677; Vacuum=4.598; Cnt=22
Tue 06/11/13 20:12:58 DSP      LOCAL_LOG       0 Part Pump Pos=0.702; Vacuum=4.628; Cnt=23
Tue 06/11/13 20:13:00 DSP      LOCAL_LOG       0 Part Pump Pos=0.727; Vacuum=4.634; Cnt=24
Tue 06/11/13 20:13:03 DSP      LOCAL_LOG       0 Part Pump Pos=0.752; Vacuum=4.592; Cnt=25
Tue 06/11/13 20:13:06 DSP      LOCAL_LOG       0 Part Pump Pos=0.777; Vacuum=4.589; Cnt=26
Tue 06/11/13 20:13:08 DSP      LOCAL_LOG       0 Part Pump Pos=0.802; Vacuum=4.564; Cnt=27
Tue 06/11/13 20:13:11 DSP      LOCAL_LOG       0 Part Pump Pos=0.827; Vacuum=4.556; Cnt=28
Tue 06/11/13 20:13:13 DSP      LOCAL_LOG       0 Part Pump Pos=0.852; Vacuum=4.581; Cnt=29
Tue 06/11/13 20:13:38 HMS      WIPE_START_STATE    0 Wipe Start: 2/7
Tue 06/11/13 20:14:22 HMS      WIPE_START_STATE    0 Wipe Start: 3/7
Tue 06/11/13 20:15:06 HMS      WIPE_START_STATE    0 Wipe Start: 4/7
Tue 06/11/13 20:15:49 HMS      WIPE_START_STATE    0 Wipe Start: 5/7
Tue 06/11/13 20:16:33 HMS      WIPE_START_STATE    0 Wipe Start: 6/7
Tue 06/11/13 20:17:17 HMS      WIPE_START_STATE    0 Wipe Start: 7/7
Tue 06/11/13 20:18:00 HMS      WIPE_WAIT_GROUP_FIRE    0 Wipe Fire
Tue 06/11/13 20:18:01 DSP      LOG             0 Sending Normalization
Tue 06/11/13 20:18:13 DSP      LOG             0 Test Fire 90000 times at 24.00 kHz
Tue 06/11/13 20:18:13 DSP      LOG             0 Test Reg = D181 2181
Tue 06/11/13 20:18:22 HMS      WIPE_X_AT_DUMP_STATE    0 Wipe At Dump
Tue 06/11/13 20:19:35 HMS      WIPE_WAIT_DRIP_STOP_2    0
Tue 06/11/13 20:19:50 HMS      WIPE_X_PARKED    0
Tue 06/11/13 20:19:54 HMS      WIPE_SOLENOID_DISENGAGE    0 Wipe Parked
Tue 06/11/13 20:20:08 HMS      WIPE_WAIT_Z_BUILD_START    0
Tue 06/11/13 20:20:19 HMS      WIPE_INACTIVE    0 Printhead Maintenance Completed
Tue 06/11/13 20:20:20 DSP      LOCAL_LOG       0 Printhead Maintenance Completed
Tue 06/11/13 20:20:20 BUILD    TEST_PRINT      0
Tue 06/11/13 20:20:21 DEBUG    NOTICE         0 Send Parameters To DSP
Tue 06/11/13 20:20:21 DSP      LOG             0 Begin Build
Tue 06/11/13 20:20:21 DSP      LOG             0 Sending Normalization
Tue 06/11/13 20:20:21 DEBUG    TEMP_STATE_CHANGE    7 Control Build; Delay: 10
Tue 06/11/13 20:20:21 DSP      LOCAL_LOG       0 Realtime BUILD_PART
Tue 06/11/13 20:20:24 DSP      LOG             0 Test Pattern = 0
Tue 06/11/13 20:20:44 DSP      LOG             0 Finishing Job
Tue 06/11/13 20:20:47 DSP      LOG             0 Waiting For Secondary Thread
Tue 06/11/13 20:20:47 DEBUG    NOTICE         0 Send Parameters To DSP
Tue 06/11/13 20:20:47 DSP      LOG             0 Build Done
Tue 06/11/13 20:20:47 BUILD    POST_CURE       0 Z Pos:  0.0000; ZL Encoder:  0.0000; ZR Encoder:  0.0000
Tue 06/11/13 20:20:47 DSP      LOG             0 Servo Enabled by PC
Tue 06/11/13 20:20:47 DSP      LOG             0 Beginning Post Cure
Tue 06/11/13 20:20:47 DSP      LOG             0 Lamp On       0.05
Tue 06/11/13 20:20:47 DSP      LOG             0 Lamp Off      3.84
Tue 06/11/13 20:20:47 DSP      LOG             0 Lamp Inches   3.79
Tue 06/11/13 20:20:47 DSP      LOG             0 Curing Layer 1 of 10
Tue 06/11/13 20:21:07 DSP      LOG             0 Curing Layer 2 of 10
Tue 06/11/13 20:21:25 DSP      LOG             0 Curing Layer 3 of 10
Tue 06/11/13 20:21:42 DSP      LOG             0 Curing Layer 4 of 10
Tue 06/11/13 20:21:59 DSP      LOG             0 Curing Layer 5 of 10
Tue 06/11/13 20:22:17 DSP      LOG             0 Curing Layer 6 of 10
Tue 06/11/13 20:22:34 DSP      LOG             0 Curing Layer 7 of 10
Tue 06/11/13 20:22:52 DSP      LOG             0 Curing Layer 8 of 10
Tue 06/11/13 20:23:09 DSP      LOG             0 Curing Layer 9 of 10
Tue 06/11/13 20:23:27 DSP      LOG             0 Curing Layer 10 of 10
Tue 06/11/13 20:23:44 DSP      LOG             0 Post Cure Complete
Tue 06/11/13 20:23:48 BUILD    DONE            0
Tue 06/11/13 20:23:49 BUILD    WAIT_RAISE_PLATFORM    0
Tue 06/11/13 20:23:49 DEBUG    TEMP_STATE_CHANGE    7 Control Build; Delay: 10
Tue 06/11/13 20:23:49 DSP      LOCAL_LOG       0 Realtime GO_TO_BUILD
Tue 06/11/13 20:23:49 DSP      LOCAL_LOG       0 Realtime READY_TO_BUILD
Tue 06/11/13 20:23:50 DSP      LOG             0 Raise Z
Tue 06/11/13 20:25:18 DSP      LOG             0 Z Top Limit Detected
Tue 06/11/13 20:25:18 BUILD    REMOVE_PLATFORM    0
Tue 06/11/13 20:25:18 DSP      LOG             0 Servo Disabled by PC
Tue 06/11/13 20:25:18 DEBUG    NOTICE         0 ABORT:
Tue 06/11/13 20:25:18 DEBUG    NOTICE         0 Elapsed Time = 00:02
Tue 06/11/13 20:25:18 DEBUG    PARAM_CHANGE    0 LoadBuildStyle: STANDARD FRACTAL
Tue 06/11/13 20:30:34 BUILD    WAIT_READY      0
Tue 06/11/13 20:30:35 DEBUG    TEMP_STATE_CHANGE    7 Control Build; Delay: 10
Tue 06/11/13 20:30:35 DSP      LOCAL_LOG       0 Realtime GO_TO_BUILD
Tue 06/11/13 20:30:35 DSP      LOCAL_LOG       0 Realtime READY_TO_BUILD
Tue 06/11/13 20:52:03 SECURITY GET_SECURITY_INDEX     0 Index = 0
Tue 06/11/13 20:52:12 DEBUG    DIALOG_OPERATION    0 Stage Dialog Opened - SD FRACTAL
Tue 06/11/13 20:52:14 DEBUG    DIALOG_OPERATION    0 Stage Dialog Closed - SD FRACTAL
Tue 06/11/13 21:08:09 DEBUG    BTN_PRESSED    1 Online Pressed
Tue 06/11/13 21:08:10 BUILD    PRE_JOB_CHECKS    0
Tue 06/11/13 21:08:16 DEBUG    BTN_PRESSED   11 Yes Pressed
Tue 06/11/13 21:08:26 DEBUG    NOTICE         0 Send Parameters To DSP
Tue 06/11/13 21:08:26 DEBUG    TEMP_STATE_CHANGE    7 Control Build; Delay: 10
Tue 06/11/13 21:08:26 DSP      LOCAL_LOG       0 Realtime GO_TO_BUILD
Tue 06/11/13 21:08:26 DSP      LOCAL_LOG       0 Realtime READY_TO_BUILD
Tue 06/11/13 21:08:26 DSP      LOG             0 Servo Enabled by PC
Tue 06/11/13 21:08:26 BUILD    HOME_XY         0
Tue 06/11/13 21:08:27 DSP      LOG             0 Home X
Tue 06/11/13 21:08:28 DSP      LOG             0 Detected X Limit
Tue 06/11/13 21:08:28 DSP      LOG             0 Home Y
Tue 06/11/13 21:08:37 DSP      LOG             0 Detected Y Limit
Tue 06/11/13 21:08:37 BUILD    HOME_Z          0
Tue 06/11/13 21:08:38 DSP      LOG             0 Home Z
Tue 06/11/13 21:10:10 DSP      LOG             0 Z Right Limit Detected
Tue 06/11/13 21:10:10 DSP      LOG             0 Z Left Limit Detected
Tue 06/11/13 21:10:10 DSP      LOG             0 Delta Z set to -0.015000
Tue 06/11/13 21:10:10 BUILD    ONLINE          0
Tue 06/11/13 21:13:43 TCP      STORE_FILE      0  File:C:\ProJet\Bin\..\work\21134.ctl
Tue 06/11/13 21:13:44 TCP      SEND_JOB        0 192.168.10.56: msnider@cv93gq1_engdsn-0011
Tue 06/11/13 21:13:44 PREP     CTL_COMBINE_JOBS     0
Tue 06/11/13 21:13:44 DSP      LOG             0 DSP Comm Reset by PC
Tue 06/11/13 21:13:44 PREP     OPEN_FILES        0 Build Style: Standard
Tue 06/11/13 21:13:44 DEBUG    PARAM_CHANGE    0 LoadBuildStyle: STANDARD FRACTAL
Tue 06/11/13 21:13:45 PREP     CTL_INITIALIZE    3 Input File: C:\ProJet\Bin\..\work\21134.ctl, Support Type: FRACTAL, Minimum Supports: 0.216000, Draft Angle: 0
Tue 06/11/13 21:13:45 BUILD    PRE_BUILD       0
Tue 06/11/13 21:13:46 PREP     FRACTAL_DONE         0 Extents: X 0.442144 8.534242  Y 0.584092 6.960882  Z 0.000000 1.207830
Tue 06/11/13 21:13:49 BUILD    BLD_HEAD_CLEANING    0
Tue 06/11/13 21:13:52 HMS      WIPE_INITIATE    0 Materials Present - Head Cleaning Initiated
Tue 06/11/13 21:13:52 HMS      WIPE_MOVE_Z_TO_PICKUP    0 Beginning Printhead Maintenance
Tue 06/11/13 21:14:04 PREP     CTL_FINISH_SUPPORTS    0
Tue 06/11/13 21:14:04 PREP     CTL_GET_INITIAL_TOKENS    0 Filtering Zones; m_iZonePoolIndex = 12009
Tue 06/11/13 21:14:38 HMS      WIPE_CYCLE_START_STATE    0
Tue 06/11/13 21:14:52 HMS      WIPE_WAIT_GROUP_FIRE    0 Wipe Fire
Tue 06/11/13 21:14:53 DSP      LOG             0 Sending Normalization
Tue 06/11/13 21:15:05 DSP      LOG             0 Test Fire 90000 times at 24.00 kHz
Tue 06/11/13 21:15:05 DSP      LOG             0 Test Reg = D181 2181
Tue 06/11/13 21:15:10 HMS      WIPE_X_PARKED    0
Tue 06/11/13 21:15:17 HMS      WIPE_SOLENOID_DISENGAGE    0 Wipe Parked
Tue 06/11/13 21:15:31 HMS      WIPE_WAIT_Z_BUILD_START    0
Tue 06/11/13 21:16:09 HMS      WIPE_INACTIVE    0 Printhead Maintenance Completed
Tue 06/11/13 21:16:09 DSP      LOCAL_LOG       0 Printhead Maintenance Completed
Tue 06/11/13 21:16:10 BUILD    BUILD_BEGIN     0
Tue 06/11/13 21:16:10 DEBUG    TEMP_STATE_CHANGE    7 Control Build; Delay: 10
Tue 06/11/13 21:16:10 DSP      LOCAL_LOG       0 Realtime BUILD_PART
Tue 06/11/13 21:16:12 DSP      LOG             0 Manual Cure UV LEDS  2.0 Seconds
Tue 06/11/13 21:16:14 DSP      LOG             0 Latched 1701 1379 2070 2012
Tue 06/11/13 21:16:15 DSP      LOG             0 Manual Cure UV LEDS  2.0 Seconds
Tue 06/11/13 21:16:17 DSP      LOG             0 Latched 1779 1443 2066 1941
Tue 06/11/13 21:16:17 DSP      LOG             0 Manual Cure UV LEDS  2.0 Seconds
Tue 06/11/13 21:16:19 DSP      LOG             0 Latched 1678 1379 2008 1849
Tue 06/11/13 21:16:19 DSP      LOG             0 Measure Uv Leds
Tue 06/11/13 21:16:19 DSP      LOG             0 Measured 1779 1443 2066 1941
Tue 06/11/13 21:16:21 DSP      LOG             0 Begin Build
Tue 06/11/13 21:16:21 BUILD    BUILD_FANS_OFF    0
Tue 06/11/13 21:16:34 DSP      LOG             0 Sending Normalization
Tue 06/11/13 21:16:34 DSP      LOG             0 Build Mode = 0
Tue 06/11/13 21:16:34 BUILD    BUILD           0
Tue 06/11/13 21:16:34 DSP      LOG             0 Build Extents
Tue 06/11/13 21:16:34 DSP      LOG             0 X -   0.000000    8.148419
Tue 06/11/13 21:16:34 DSP      LOG             0 Y -   0.000000    6.431039
Tue 06/11/13 21:16:34 DSP      LOG             0 Z -   0.000000    1.207370
Tue 06/11/13 21:16:34 DSP      LOG             0 Pixel Size -   0.003045    0.003045
Tue 06/11/13 21:16:34 DSP      LOG             0 Slice Layer Thickness -   0.001580
Tue 06/11/13 21:16:34 DSP      LOG             0 Printing Layer 1 of 764
Tue 06/11/13 21:16:58 DSP      LOG             0 Printing Layer 2 of 764
Tue 06/11/13 21:17:22 DSP      LOG             0 Printing Layer 3 of 764
Tue 06/11/13 21:17:45 DSP      LOG             0 Printing Layer 4 of 764
Tue 06/11/13 21:18:07 DSP      LOG             0 Printing Layer 5 of 764
Tue 06/11/13 21:18:29 DSP      LOG             0 Printing Layer 6 of 764
Tue 06/11/13 21:18:51 DSP      LOG             0 Printing Layer 7 of 764
Tue 06/11/13 21:19:13 DSP      LOG             0 Printing Layer 8 of 764
Tue 06/11/13 21:19:35 DSP      LOG             0 Printing Layer 9 of 764
Tue 06/11/13 21:19:57 DSP      LOG             0 Printing Layer 10 of 764
Tue 06/11/13 21:20:20 DSP      LOG             0 Printing Layer 11 of 764
Tue 06/11/13 21:20:42 DSP      LOG             0 Printing Layer 12 of 764
Tue 06/11/13 21:21:04 DSP      LOG             0 Printing Layer 13 of 764
Tue 06/11/13 21:21:26 DSP      LOG             0 Printing Layer 14 of 764
Tue 06/11/13 21:21:48 DSP      LOG             0 Printing Layer 15 of 764
Tue 06/11/13 21:22:10 DSP      LOG             0 Printing Layer 16 of 764
Tue 06/11/13 21:22:33 DSP      LOG             0 Printing Layer 17 of 764
Tue 06/11/13 21:22:55 DSP      LOG             0 Printing Layer 18 of 764
Tue 06/11/13 21:23:17 DSP      LOG             0 Printing Layer 19 of 764
Tue 06/11/13 21:23:39 DSP      LOG             0 Printing Layer 20 of 764
Tue 06/11/13 21:24:01 DSP      LOG             0 Printing Layer 21 of 764
Tue 06/11/13 21:24:24 DSP      LOG             0 Printing Layer 22 of 764
Tue 06/11/13 21:24:46 DSP      LOG             0 Printing Layer 23 of 764
Tue 06/11/13 21:25:10 DSP      LOG             0 Printing Layer 24 of 764
Tue 06/11/13 21:25:32 DSP      LOG             0 Printing Layer 25 of 764
Tue 06/11/13 21:25:54 DSP      LOG             0 Printing Layer 26 of 764
Tue 06/11/13 21:26:16 DSP      LOG             0 Printing Layer 27 of 764
Tue 06/11/13 21:26:18 DSP      LOCAL_LOG       0 Support Pump Pos=0.052; Vacuum=4.614; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=746 sec; MPixels/Sec=0.000000
Tue 06/11/13 21:26:38 DSP      LOG             0 Printing Layer 28 of 764
Tue 06/11/13 21:27:01 DSP      LOG             0 Printing Layer 29 of 764
Tue 06/11/13 21:27:23 DSP      LOG             0 Printing Layer 30 of 764
Tue 06/11/13 21:27:45 DSP      LOG             0 Printing Layer 31 of 764
Tue 06/11/13 21:28:07 DSP      LOG             0 Printing Layer 32 of 764
Tue 06/11/13 21:28:29 DSP      LOG             0 Printing Layer 33 of 764
Tue 06/11/13 21:28:51 DSP      LOG             0 Printing Layer 34 of 764
Tue 06/11/13 21:29:14 DSP      LOG             0 Printing Layer 35 of 764
Tue 06/11/13 21:29:36 DSP      LOG             0 Printing Layer 36 of 764
Tue 06/11/13 21:29:58 DSP      LOG             0 Printing Layer 37 of 764
Tue 06/11/13 21:30:20 DSP      LOG             0 Printing Layer 38 of 764
Tue 06/11/13 21:30:25 DSP      LOCAL_LOG       0 Support Pump Pos=0.077; Vacuum=4.609; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=247 sec; MPixels/Sec=0.000000
Tue 06/11/13 21:30:42 DSP      LOG             0 Printing Layer 39 of 764
Tue 06/11/13 21:31:05 DSP      LOG             0 Printing Layer 40 of 764
Tue 06/11/13 21:31:27 DSP      LOG             0 Printing Layer 41 of 764
Tue 06/11/13 21:31:49 DSP      LOG             0 Printing Layer 42 of 764
Tue 06/11/13 21:32:11 DSP      LOG             0 Printing Layer 43 of 764
Tue 06/11/13 21:32:33 DSP      LOG             0 Printing Layer 44 of 764
Tue 06/11/13 21:32:56 DSP      LOG             0 Printing Layer 45 of 764
Tue 06/11/13 21:33:20 DSP      LOG             0 Printing Layer 46 of 764
Tue 06/11/13 21:33:42 DSP      LOG             0 Printing Layer 47 of 764
Tue 06/11/13 21:34:04 DSP      LOG             0 Printing Layer 48 of 764
Tue 06/11/13 21:34:26 DSP      LOG             0 Printing Layer 49 of 764
Tue 06/11/13 21:34:49 DSP      LOG             0 Printing Layer 50 of 764
Tue 06/11/13 21:35:11 DSP      LOG             0 S Ratio = 43.6, 32.7
Tue 06/11/13 21:35:11 DSP      LOG             0 Printing Layer 51 of 764
Tue 06/11/13 21:35:33 DSP      LOG             0 Printing Layer 52 of 764
Tue 06/11/13 21:35:45 DSP      LOCAL_LOG       0 Support Pump Pos=0.102; Vacuum=4.595; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=320 sec; MPixels/Sec=0.000000
Tue 06/11/13 21:35:55 DSP      LOG             0 Printing Layer 53 of 764
Tue 06/11/13 21:36:17 DSP      LOG             0 Printing Layer 54 of 764
Tue 06/11/13 21:36:40 DSP      LOG             0 Printing Layer 55 of 764
Tue 06/11/13 21:37:02 DSP      LOG             0 Printing Layer 56 of 764
Tue 06/11/13 21:37:24 DSP      LOG             0 Printing Layer 57 of 764
Tue 06/11/13 21:37:46 DSP      LOG             0 Printing Layer 58 of 764
Tue 06/11/13 21:38:08 DSP      LOG             0 Printing Layer 59 of 764
Tue 06/11/13 21:38:30 DSP      LOG             0 Printing Layer 60 of 764
Tue 06/11/13 21:38:53 DSP      LOG             0 Printing Layer 61 of 764
Tue 06/11/13 21:39:15 DSP      LOG             0 Printing Layer 62 of 764
Tue 06/11/13 21:39:37 DSP      LOG             0 Printing Layer 63 of 764
Tue 06/11/13 21:39:59 DSP      LOG             0 Printing Layer 64 of 764
Tue 06/11/13 21:40:21 DSP      LOG             0 Printing Layer 65 of 764
Tue 06/11/13 21:40:44 DSP      LOG             0 Printing Layer 66 of 764
Tue 06/11/13 21:40:49 DSP      LOCAL_LOG       0 Support Pump Pos=0.127; Vacuum=4.592; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=304 sec; MPixels/Sec=0.000000
Tue 06/11/13 21:41:06 DSP      LOG             0 Printing Layer 67 of 764
Tue 06/11/13 21:41:30 DSP      LOG             0 Printing Layer 68 of 764
Tue 06/11/13 21:41:52 DSP      LOG             0 Printing Layer 69 of 764
Tue 06/11/13 21:42:15 DSP      LOG             0 Printing Layer 70 of 764
Tue 06/11/13 21:42:37 DSP      LOG             0 Printing Layer 71 of 764
Tue 06/11/13 21:42:59 DSP      LOG             0 Printing Layer 72 of 764
Tue 06/11/13 21:43:21 DSP      LOG             0 Printing Layer 73 of 764
Tue 06/11/13 21:43:43 DSP      LOG             0 Printing Layer 74 of 764
Tue 06/11/13 21:44:05 DSP      LOG             0 Printing Layer 75 of 764
Tue 06/11/13 21:44:28 DSP      LOG             0 S Ratio = 41.6, 35.0
Tue 06/11/13 21:44:28 DSP      LOG             0 Printing Layer 76 of 764
Tue 06/11/13 21:44:50 DSP      LOG             0 Printing Layer 77 of 764
Tue 06/11/13 21:45:12 DSP      LOG             0 Printing Layer 78 of 764
Tue 06/11/13 21:45:34 DSP      LOG             0 Printing Layer 79 of 764
Tue 06/11/13 21:45:36 DSP      LOCAL_LOG       0 Support Pump Pos=0.152; Vacuum=4.603; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=287 sec; MPixels/Sec=0.000000
Tue 06/11/13 21:45:56 DSP      LOG             0 Printing Layer 80 of 764
Tue 06/11/13 21:46:19 DSP      LOG             0 Printing Layer 81 of 764
Tue 06/11/13 21:46:35 DEBUG    NOTICE         0 Bag Heater On
Tue 06/11/13 21:46:41 DSP      LOG             0 Printing Layer 82 of 764
Tue 06/11/13 21:47:03 DSP      LOG             0 Printing Layer 83 of 764
Tue 06/11/13 21:47:25 DSP      LOG             0 Printing Layer 84 of 764
Tue 06/11/13 21:47:48 DSP      LOG             0 Printing Layer 85 of 764
Tue 06/11/13 21:48:10 DSP      LOG             0 Printing Layer 86 of 764
Tue 06/11/13 21:48:32 DSP      LOG             0 Printing Layer 87 of 764
Tue 06/11/13 21:48:54 DSP      LOG             0 Printing Layer 88 of 764
Tue 06/11/13 21:49:16 DSP      LOG             0 Printing Layer 89 of 764
Tue 06/11/13 21:49:41 DSP      LOG             0 Printing Layer 90 of 764
Tue 06/11/13 21:50:03 DSP      LOG             0 Printing Layer 91 of 764
Tue 06/11/13 21:50:22 DSP      LOCAL_LOG       0 Support Pump Pos=0.177; Vacuum=4.609; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=286 sec; MPixels/Sec=0.000000
Tue 06/11/13 21:50:25 DSP      LOG             0 Printing Layer 92 of 764
Tue 06/11/13 21:50:47 DSP      LOG             0 Printing Layer 93 of 764
Tue 06/11/13 21:51:09 DSP      LOG             0 Printing Layer 94 of 764
Tue 06/11/13 21:51:31 DSP      LOG             0 Printing Layer 95 of 764
Tue 06/11/13 21:51:53 DSP      LOG             0 Printing Layer 96 of 764
Tue 06/11/13 21:52:16 DSP      LOG             0 Printing Layer 97 of 764
Tue 06/11/13 21:52:47 DSP      LOG             0 Printing Layer 98 of 764
Tue 06/11/13 21:53:18 DSP      LOG             0 Printing Layer 99 of 764
Tue 06/11/13 21:53:50 DSP      LOG             0 Printing Layer 100 of 764
Tue 06/11/13 21:54:21 DSP      LOG             0 S Ratio = 46.1, 38.3
Tue 06/11/13 21:54:21 DSP      LOG             0 Printing Layer 101 of 764
Tue 06/11/13 21:54:52 DSP      LOG             0 Printing Layer 102 of 764
Tue 06/11/13 21:55:24 DSP      LOG             0 Printing Layer 103 of 764
Tue 06/11/13 21:55:55 DSP      LOG             0 Printing Layer 104 of 764
Tue 06/11/13 21:56:15 DSP      LOCAL_LOG       0 Support Pump Pos=0.202; Vacuum=4.595; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=353 sec; MPixels/Sec=0.000000
Tue 06/11/13 21:56:26 DSP      LOG             0 Printing Layer 105 of 764
Tue 06/11/13 21:56:58 DSP      LOG             0 Printing Layer 106 of 764
Tue 06/11/13 21:57:29 DSP      LOG             0 Printing Layer 107 of 764
Tue 06/11/13 21:58:00 DSP      LOG             0 Printing Layer 108 of 764
Tue 06/11/13 21:58:32 DSP      LOG             0 Printing Layer 109 of 764
Tue 06/11/13 21:59:03 DSP      LOG             0 Printing Layer 110 of 764
Tue 06/11/13 21:59:34 DSP      LOG             0 Printing Layer 111 of 764
Tue 06/11/13 22:00:08 DSP      LOG             0 Printing Layer 112 of 764
Tue 06/11/13 22:00:39 DSP      LOG             0 Printing Layer 113 of 764
Tue 06/11/13 22:01:10 DSP      LOG             0 Printing Layer 114 of 764
Tue 06/11/13 22:01:42 DSP      LOG             0 Printing Layer 115 of 764
Tue 06/11/13 22:02:13 DSP      LOG             0 Printing Layer 116 of 764
Tue 06/11/13 22:02:37 DSP      LOCAL_LOG       0 Support Pump Pos=0.227; Vacuum=4.609; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=382 sec; MPixels/Sec=0.000000
Tue 06/11/13 22:02:44 DSP      LOG             0 Printing Layer 117 of 764
Tue 06/11/13 22:03:16 DSP      LOG             0 Printing Layer 118 of 764
Tue 06/11/13 22:03:47 DSP      LOG             0 Printing Layer 119 of 764
Tue 06/11/13 22:04:18 DSP      LOG             0 Printing Layer 120 of 764
Tue 06/11/13 22:04:50 DSP      LOG             0 Printing Layer 121 of 764
Tue 06/11/13 22:05:21 DSP      LOG             0 Printing Layer 122 of 764
Tue 06/11/13 22:05:52 DSP      LOG             0 Printing Layer 123 of 764
Tue 06/11/13 22:06:24 DSP      LOG             0 Printing Layer 124 of 764
Tue 06/11/13 22:06:55 DSP      LOG             0 Printing Layer 125 of 764
Tue 06/11/13 22:07:26 DSP      LOG             0 S Ratio = 44.6, 41.2
Tue 06/11/13 22:07:26 DSP      LOG             0 Printing Layer 126 of 764
Tue 06/11/13 22:07:58 DSP      LOG             0 Printing Layer 127 of 764
Tue 06/11/13 22:08:29 DSP      LOG             0 Printing Layer 128 of 764
Tue 06/11/13 22:09:00 DSP      LOG             0 Printing Layer 129 of 764
Tue 06/11/13 22:09:22 DSP      LOCAL_LOG       0 Support Pump Pos=0.252; Vacuum=4.606; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=405 sec; MPixels/Sec=0.000000
Tue 06/11/13 22:09:32 DSP      LOG             0 Printing Layer 130 of 764
Tue 06/11/13 22:10:03 DSP      LOG             0 Printing Layer 131 of 764
Tue 06/11/13 22:10:34 DSP      LOG             0 Printing Layer 132 of 764
Tue 06/11/13 22:11:08 DSP      LOG             0 Printing Layer 133 of 764
Tue 06/11/13 22:11:39 DSP      LOG             0 Printing Layer 134 of 764
Tue 06/11/13 22:12:11 DSP      LOG             0 Printing Layer 135 of 764
Tue 06/11/13 22:12:42 DSP      LOG             0 Printing Layer 136 of 764
Tue 06/11/13 22:13:13 DSP      LOG             0 Printing Layer 137 of 764
Tue 06/11/13 22:13:44 DSP      LOG             0 Printing Layer 138 of 764
Tue 06/11/13 22:14:16 DSP      LOG             0 Printing Layer 139 of 764
Tue 06/11/13 22:14:47 DSP      LOG             0 Printing Layer 140 of 764
Tue 06/11/13 22:15:11 DSP      LOCAL_LOG       0 Support Pump Pos=0.277; Vacuum=4.603; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=349 sec; MPixels/Sec=0.000000
Tue 06/11/13 22:15:18 DSP      LOG             0 Printing Layer 141 of 764
Tue 06/11/13 22:15:50 DSP      LOG             0 Printing Layer 142 of 764
Tue 06/11/13 22:16:21 DSP      LOG             0 Printing Layer 143 of 764
Tue 06/11/13 22:16:36 DEBUG    NOTICE         0 Bag Heater Off
Tue 06/11/13 22:16:52 DSP      LOG             0 Printing Layer 144 of 764
Tue 06/11/13 22:17:24 DSP      LOG             0 Printing Layer 145 of 764
Tue 06/11/13 22:17:55 DSP      LOG             0 Printing Layer 146 of 764
Tue 06/11/13 22:18:26 DSP      LOG             0 Printing Layer 147 of 764
Tue 06/11/13 22:18:58 DSP      LOG             0 Printing Layer 148 of 764
Tue 06/11/13 22:19:29 DSP      LOG             0 Printing Layer 149 of 764
Tue 06/11/13 22:20:00 DSP      LOG             0 Printing Layer 150 of 764
Tue 06/11/13 22:20:32 DSP      LOG             0 S Ratio = 47.6, 44.7
Tue 06/11/13 22:20:32 DSP      LOG             0 Printing Layer 151 of 764
Tue 06/11/13 22:21:03 DSP      LOG             0 Printing Layer 152 of 764
Tue 06/11/13 22:21:35 DSP      LOG             0 Printing Layer 153 of 764
Tue 06/11/13 22:21:57 DSP      LOCAL_LOG       0 Support Pump Pos=0.302; Vacuum=4.589; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=406 sec; MPixels/Sec=0.000000
Tue 06/11/13 22:22:06 DSP      LOG             0 Printing Layer 154 of 764
Tue 06/11/13 22:22:39 DSP      LOG             0 Printing Layer 155 of 764
Tue 06/11/13 22:23:11 DSP      LOG             0 Printing Layer 156 of 764
Tue 06/11/13 22:23:42 DSP      LOG             0 Printing Layer 157 of 764
Tue 06/11/13 22:24:13 DSP      LOG             0 Printing Layer 158 of 764
Tue 06/11/13 22:24:45 DSP      LOG             0 Printing Layer 159 of 764
Tue 06/11/13 22:25:16 DSP      LOG             0 Printing Layer 160 of 764
Tue 06/11/13 22:25:47 DSP      LOG             0 Printing Layer 161 of 764
Tue 06/11/13 22:26:18 DSP      LOG             0 Printing Layer 162 of 764
Tue 06/11/13 22:26:50 DSP      LOG             0 Printing Layer 163 of 764
Tue 06/11/13 22:27:21 DSP      LOG             0 Printing Layer 164 of 764
Tue 06/11/13 22:27:52 DSP      LOG             0 Printing Layer 165 of 764
Tue 06/11/13 22:28:24 DSP      LOG             0 Printing Layer 166 of 764
Tue 06/11/13 22:28:48 DSP      LOCAL_LOG       0 Support Pump Pos=0.327; Vacuum=4.578; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=411 sec; MPixels/Sec=0.000000
Tue 06/11/13 22:28:55 DSP      LOG             0 Printing Layer 167 of 764
Tue 06/11/13 22:29:26 DSP      LOG             0 Printing Layer 168 of 764
Tue 06/11/13 22:29:58 DSP      LOG             0 Printing Layer 169 of 764
Tue 06/11/13 22:30:29 DSP      LOG             0 Printing Layer 170 of 764
Tue 06/11/13 22:31:01 DSP      LOG             0 Printing Layer 171 of 764
Tue 06/11/13 22:31:32 DSP      LOG             0 Printing Layer 172 of 764
Tue 06/11/13 22:32:03 DSP      LOG             0 Printing Layer 173 of 764
Tue 06/11/13 22:32:34 DSP      LOG             0 Printing Layer 174 of 764
Tue 06/11/13 22:33:06 DSP      LOG             0 Printing Layer 175 of 764
Tue 06/11/13 22:33:37 DSP      LOG             0 S Ratio = 45.5, 45.1
Tue 06/11/13 22:33:37 DSP      LOG             0 Printing Layer 176 of 764
Tue 06/11/13 22:34:11 DSP      LOG             0 Printing Layer 177 of 764
Tue 06/11/13 22:34:42 DSP      LOG             0 Printing Layer 178 of 764
Tue 06/11/13 22:35:13 DSP      LOG             0 Printing Layer 179 of 764
Tue 06/11/13 22:35:36 DSP      LOCAL_LOG       0 Support Pump Pos=0.352; Vacuum=4.572; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=408 sec; MPixels/Sec=0.000000
Tue 06/11/13 22:35:44 DSP      LOG             0 Printing Layer 180 of 764
Tue 06/11/13 22:36:16 DSP      LOG             0 Printing Layer 181 of 764
Tue 06/11/13 22:36:47 DSP      LOG             0 Printing Layer 182 of 764
Tue 06/11/13 22:37:18 DSP      LOG             0 Printing Layer 183 of 764
Tue 06/11/13 22:37:50 DSP      LOG             0 Printing Layer 184 of 764
Tue 06/11/13 22:38:21 DSP      LOG             0 Printing Layer 185 of 764
Tue 06/11/13 22:38:52 DSP      LOG             0 Printing Layer 186 of 764
Tue 06/11/13 22:39:24 DSP      LOG             0 Printing Layer 187 of 764
Tue 06/11/13 22:39:55 DSP      LOG             0 Printing Layer 188 of 764
Tue 06/11/13 22:40:26 DSP      LOG             0 Printing Layer 189 of 764
Tue 06/11/13 22:40:58 DSP      LOG             0 Printing Layer 190 of 764
Tue 06/11/13 22:41:29 DSP      LOG             0 Printing Layer 191 of 764
Tue 06/11/13 22:42:00 DSP      LOG             0 Printing Layer 192 of 764
Tue 06/11/13 22:42:24 DSP      LOCAL_LOG       0 Support Pump Pos=0.377; Vacuum=4.558; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=408 sec; MPixels/Sec=0.000000
Tue 06/11/13 22:42:32 DSP      LOG             0 Printing Layer 193 of 764
Tue 06/11/13 22:43:03 DSP      LOG             0 Printing Layer 194 of 764
Tue 06/11/13 22:43:34 DSP      LOG             0 Printing Layer 195 of 764
Tue 06/11/13 22:44:06 DSP      LOG             0 Printing Layer 196 of 764
Tue 06/11/13 22:44:37 DSP      LOG             0 Printing Layer 197 of 764
Tue 06/11/13 22:45:08 DSP      LOG             0 Printing Layer 198 of 764
Tue 06/11/13 22:45:42 DSP      LOG             0 Printing Layer 199 of 764
Tue 06/11/13 22:46:13 DSP      LOG             0 Printing Layer 200 of 764
Tue 06/11/13 22:46:37 DEBUG    NOTICE         0 Bag Heater On
Tue 06/11/13 22:46:44 DSP      LOG             0 S Ratio = 46.7, 46.1
Tue 06/11/13 22:46:45 DSP      LOG             0 Printing Layer 201 of 764
Tue 06/11/13 22:47:16 DSP      LOG             0 Printing Layer 202 of 764
Tue 06/11/13 22:47:47 DSP      LOG             0 Printing Layer 203 of 764
Tue 06/11/13 22:48:18 DSP      LOG             0 Printing Layer 204 of 764
Tue 06/11/13 22:48:50 DSP      LOG             0 Printing Layer 205 of 764
Tue 06/11/13 22:49:09 DSP      LOCAL_LOG       0 Support Pump Pos=0.402; Vacuum=4.598; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=405 sec; MPixels/Sec=0.000000
Tue 06/11/13 22:49:21 DSP      LOG             0 Printing Layer 206 of 764
Tue 06/11/13 22:49:52 DSP      LOG             0 Printing Layer 207 of 764
Tue 06/11/13 22:50:24 DSP      LOG             0 Printing Layer 208 of 764
Tue 06/11/13 22:50:55 DSP      LOG             0 Printing Layer 209 of 764
Tue 06/11/13 22:51:26 DSP      LOG             0 Printing Layer 210 of 764
Tue 06/11/13 22:51:58 DSP      LOG             0 Printing Layer 211 of 764
Tue 06/11/13 22:52:29 DSP      LOG             0 Printing Layer 212 of 764
Tue 06/11/13 22:53:00 DSP      LOG             0 Printing Layer 213 of 764
Tue 06/11/13 22:53:32 DSP      LOG             0 Printing Layer 214 of 764
Tue 06/11/13 22:54:03 DSP      LOG             0 Printing Layer 215 of 764
Tue 06/11/13 22:54:35 DSP      LOG             0 Printing Layer 216 of 764
Tue 06/11/13 22:55:06 DSP      LOG             0 Printing Layer 217 of 764
Tue 06/11/13 22:55:37 DSP      LOG             0 Printing Layer 218 of 764
Tue 06/11/13 22:55:53 DSP      LOCAL_LOG       0 Support Pump Pos=0.427; Vacuum=4.598; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=404 sec; MPixels/Sec=0.000000
Tue 06/11/13 22:56:09 DSP      LOG             0 Printing Layer 219 of 764
Tue 06/11/13 22:56:40 DSP      LOG             0 Printing Layer 220 of 764
Tue 06/11/13 22:57:13 DSP      LOG             0 Printing Layer 221 of 764
Tue 06/11/13 22:57:45 DSP      LOG             0 Printing Layer 222 of 764
Tue 06/11/13 22:58:16 DSP      LOG             0 Printing Layer 223 of 764
Tue 06/11/13 22:58:47 DSP      LOG             0 Printing Layer 224 of 764
Tue 06/11/13 22:59:19 DSP      LOG             0 Printing Layer 225 of 764
Tue 06/11/13 22:59:50 DSP      LOG             0 S Ratio = 47.2, 46.3
Tue 06/11/13 22:59:50 DSP      LOG             0 Printing Layer 226 of 764
Tue 06/11/13 23:00:21 DSP      LOG             0 Printing Layer 227 of 764
Tue 06/11/13 23:00:52 DSP      LOG             0 Printing Layer 228 of 764
Tue 06/11/13 23:01:24 DSP      LOG             0 Printing Layer 229 of 764
Tue 06/11/13 23:01:55 DSP      LOG             0 Printing Layer 230 of 764
Tue 06/11/13 23:02:27 DSP      LOG             0 Printing Layer 231 of 764
Tue 06/11/13 23:02:43 DSP      LOCAL_LOG       0 Support Pump Pos=0.452; Vacuum=4.575; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=410 sec; MPixels/Sec=0.000000
Tue 06/11/13 23:02:58 DSP      LOG             0 Printing Layer 232 of 764
Tue 06/11/13 23:03:29 DSP      LOG             0 Printing Layer 233 of 764
Tue 06/11/13 23:04:01 DSP      LOG             0 Printing Layer 234 of 764
Tue 06/11/13 23:04:32 DSP      LOG             0 Printing Layer 235 of 764
Tue 06/11/13 23:05:03 DSP      LOG             0 Printing Layer 236 of 764
Tue 06/11/13 23:05:35 DSP      LOG             0 Printing Layer 237 of 764
Tue 06/11/13 23:06:06 DSP      LOG             0 Printing Layer 238 of 764
Tue 06/11/13 23:06:37 DSP      LOG             0 Printing Layer 239 of 764
Tue 06/11/13 23:07:09 DSP      LOG             0 Printing Layer 240 of 764
Tue 06/11/13 23:07:40 DSP      LOG             0 Printing Layer 241 of 764
Tue 06/11/13 23:08:11 DSP      LOG             0 Printing Layer 242 of 764
Tue 06/11/13 23:08:45 DSP      LOG             0 Printing Layer 243 of 764
Tue 06/11/13 23:09:09 DSP      LOCAL_LOG       0 Support Pump Pos=0.477; Vacuum=4.558; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=386 sec; MPixels/Sec=0.000000
Tue 06/11/13 23:09:16 DSP      LOG             0 Printing Layer 244 of 764
Tue 06/11/13 23:09:47 DSP      LOG             0 Printing Layer 245 of 764
Tue 06/11/13 23:10:19 DSP      LOG             0 Printing Layer 246 of 764
Tue 06/11/13 23:10:50 DSP      LOG             0 Printing Layer 247 of 764
Tue 06/11/13 23:11:21 DSP      LOG             0 Printing Layer 248 of 764
Tue 06/11/13 23:11:53 DSP      LOG             0 Printing Layer 249 of 764
Tue 06/11/13 23:12:24 DSP      LOG             0 Printing Layer 250 of 764
Tue 06/11/13 23:12:55 DSP      LOG             0 S Ratio = 47.8, 47.0
Tue 06/11/13 23:12:55 DSP      LOG             0 Printing Layer 251 of 764
Tue 06/11/13 23:13:27 DSP      LOG             0 Printing Layer 252 of 764
Tue 06/11/13 23:13:58 DSP      LOG             0 Printing Layer 253 of 764
Tue 06/11/13 23:14:29 DSP      LOG             0 Printing Layer 254 of 764
Tue 06/11/13 23:15:00 DSP      LOG             0 Printing Layer 255 of 764
Tue 06/11/13 23:15:24 DSP      LOCAL_LOG       0 Support Pump Pos=0.502; Vacuum=4.584; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=375 sec; MPixels/Sec=0.000000
Tue 06/11/13 23:15:32 DSP      LOG             0 Printing Layer 256 of 764
Tue 06/11/13 23:16:03 DSP      LOG             0 Printing Layer 257 of 764
Tue 06/11/13 23:16:35 DSP      LOG             0 Printing Layer 258 of 764
Tue 06/11/13 23:16:38 DEBUG    NOTICE         0 Bag Heater Off
Tue 06/11/13 23:17:06 DSP      LOG             0 Printing Layer 259 of 764
Tue 06/11/13 23:17:37 DSP      LOG             0 Printing Layer 260 of 764
Tue 06/11/13 23:18:09 DSP      LOG             0 Printing Layer 261 of 764
Tue 06/11/13 23:18:40 DSP      LOG             0 Printing Layer 262 of 764
Tue 06/11/13 23:19:11 DSP      LOG             0 Printing Layer 263 of 764
Tue 06/11/13 23:19:45 DSP      LOG             0 Printing Layer 264 of 764
Tue 06/11/13 23:20:16 DSP      LOG             0 Printing Layer 265 of 764
Tue 06/11/13 23:20:47 DSP      LOG             0 Printing Layer 266 of 764
Tue 06/11/13 23:21:19 DSP      LOG             0 Printing Layer 267 of 764
Tue 06/11/13 23:21:50 DSP      LOG             0 Printing Layer 268 of 764
Tue 06/11/13 23:22:21 DSP      LOG             0 Printing Layer 269 of 764
Tue 06/11/13 23:22:45 DSP      LOCAL_LOG       0 Support Pump Pos=0.527; Vacuum=4.564; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=441 sec; MPixels/Sec=0.000000
Tue 06/11/13 23:22:53 DSP      LOG             0 Printing Layer 270 of 764
Tue 06/11/13 23:23:24 DSP      LOG             0 Printing Layer 271 of 764
Tue 06/11/13 23:23:55 DSP      LOG             0 Printing Layer 272 of 764
Tue 06/11/13 23:24:27 DSP      LOG             0 Printing Layer 273 of 764
Tue 06/11/13 23:24:58 DSP      LOG             0 Printing Layer 274 of 764
Tue 06/11/13 23:25:29 DSP      LOG             0 Printing Layer 275 of 764
Tue 06/11/13 23:26:00 DSP      LOG             0 S Ratio = 46.4, 46.7
Tue 06/11/13 23:26:00 DSP      LOG             0 Printing Layer 276 of 764
Tue 06/11/13 23:26:32 DSP      LOG             0 Printing Layer 277 of 764
Tue 06/11/13 23:27:03 DSP      LOG             0 Printing Layer 278 of 764
Tue 06/11/13 23:27:35 DSP      LOG             0 Printing Layer 279 of 764
Tue 06/11/13 23:28:06 DSP      LOG             0 Printing Layer 280 of 764
Tue 06/11/13 23:28:37 DSP      LOG             0 Printing Layer 281 of 764
Tue 06/11/13 23:29:09 DSP      LOG             0 Printing Layer 282 of 764
Tue 06/11/13 23:29:32 DSP      LOCAL_LOG       0 Support Pump Pos=0.552; Vacuum=4.564; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=407 sec; MPixels/Sec=0.000000
Tue 06/11/13 23:29:40 DSP      LOG             0 Printing Layer 283 of 764
Tue 06/11/13 23:30:11 DSP      LOG             0 Printing Layer 284 of 764
Tue 06/11/13 23:30:43 DSP      LOG             0 Printing Layer 285 of 764
Tue 06/11/13 23:31:16 DSP      LOG             0 Printing Layer 286 of 764
Tue 06/11/13 23:31:47 DSP      LOG             0 Printing Layer 287 of 764
Tue 06/11/13 23:32:19 DSP      LOG             0 Printing Layer 288 of 764
Tue 06/11/13 23:32:50 DSP      LOG             0 Printing Layer 289 of 764
Tue 06/11/13 23:33:21 DSP      LOG             0 Printing Layer 290 of 764
Tue 06/11/13 23:33:53 DSP      LOG             0 Printing Layer 291 of 764
Tue 06/11/13 23:34:24 DSP      LOG             0 Printing Layer 292 of 764
Tue 06/11/13 23:34:55 DSP      LOG             0 Printing Layer 293 of 764
Tue 06/11/13 23:35:27 DSP      LOG             0 Printing Layer 294 of 764
Tue 06/11/13 23:35:58 DSP      LOG             0 Printing Layer 295 of 764
Tue 06/11/13 23:36:29 DSP      LOG             0 Printing Layer 296 of 764
Tue 06/11/13 23:37:00 DSP      LOG             0 Printing Layer 297 of 764
Tue 06/11/13 23:37:24 DSP      LOCAL_LOG       0 Support Pump Pos=0.577; Vacuum=4.558; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=472 sec; MPixels/Sec=0.000000
Tue 06/11/13 23:37:32 DSP      LOG             0 Printing Layer 298 of 764
Tue 06/11/13 23:38:03 DSP      LOG             0 Printing Layer 299 of 764
Tue 06/11/13 23:38:34 DSP      LOG             0 Printing Layer 300 of 764
Tue 06/11/13 23:39:06 DSP      LOG             0 S Ratio = 42.1, 46.0
Tue 06/11/13 23:39:06 DSP      LOG             0 Printing Layer 301 of 764
Tue 06/11/13 23:39:37 DSP      LOG             0 Printing Layer 302 of 764
Tue 06/11/13 23:40:09 DSP      LOG             0 Printing Layer 303 of 764
Tue 06/11/13 23:40:40 DSP      LOG             0 Printing Layer 304 of 764
Tue 06/11/13 23:41:11 DSP      LOG             0 Printing Layer 305 of 764
Tue 06/11/13 23:41:43 DSP      LOG             0 Printing Layer 306 of 764
Tue 06/11/13 23:42:14 DSP      LOG             0 Printing Layer 307 of 764
Tue 06/11/13 23:42:47 DSP      LOG             0 Printing Layer 308 of 764
Tue 06/11/13 23:43:19 DSP      LOG             0 Printing Layer 309 of 764
Tue 06/11/13 23:43:50 DSP      LOG             0 Printing Layer 310 of 764
Tue 06/11/13 23:44:21 DSP      LOG             0 Printing Layer 311 of 764
Tue 06/11/13 23:44:53 DSP      LOG             0 Printing Layer 312 of 764
Tue 06/11/13 23:45:17 DSP      LOCAL_LOG       0 Support Pump Pos=0.602; Vacuum=4.553; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=473 sec; MPixels/Sec=0.000000
Tue 06/11/13 23:45:24 DSP      LOG             0 Printing Layer 313 of 764
Tue 06/11/13 23:45:55 DSP      LOG             0 Printing Layer 314 of 764
Tue 06/11/13 23:46:26 DSP      LOG             0 Printing Layer 315 of 764
Tue 06/11/13 23:46:39 DEBUG    NOTICE         0 Bag Heater On
Tue 06/11/13 23:46:58 DSP      LOG             0 Printing Layer 316 of 764
Tue 06/11/13 23:47:29 DSP      LOG             0 Printing Layer 317 of 764
Tue 06/11/13 23:48:00 DSP      LOG             0 Printing Layer 318 of 764
Tue 06/11/13 23:48:32 DSP      LOG             0 Printing Layer 319 of 764
Tue 06/11/13 23:49:03 DSP      LOG             0 Printing Layer 320 of 764
Tue 06/11/13 23:49:28 DSP      LOCAL_LOG       0 Part Pump Pos=0.877; Vacuum=4.547; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=9336 sec; MPixels/Sec=0.000000
Tue 06/11/13 23:49:31 DSP      LOCAL_LOG       0 Part Pump Pos=0.877; Vacuum=4.550; Cnt=2
Tue 06/11/13 23:49:35 DSP      LOG             0 Printing Layer 321 of 764
Tue 06/11/13 23:49:57 DSP      LOCAL_LOG       0 Part Pump Pos=0.927; Vacuum=4.550; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=29 sec; MPixels/Sec=0.000000
Tue 06/11/13 23:50:00 DSP      LOCAL_LOG       0 Part Pump Pos=0.927; Vacuum=4.547; Cnt=2
Tue 06/11/13 23:50:02 DSP      LOCAL_LOG       0 Part Pump Pos=0.927; Vacuum=4.525; Cnt=3
Tue 06/11/13 23:50:05 DSP      LOCAL_LOG       0 Part Pump Pos=0.927; Vacuum=4.511; Cnt=4
Tue 06/11/13 23:50:06 DSP      LOG             0 Printing Layer 322 of 764
Tue 06/11/13 23:50:37 DSP      LOG             0 Printing Layer 323 of 764
Tue 06/11/13 23:51:09 DSP      LOG             0 Printing Layer 324 of 764
Tue 06/11/13 23:51:40 DSP      LOG             0 Printing Layer 325 of 764
Tue 06/11/13 23:52:11 DSP      LOG             0 S Ratio = 80.9, 52.9
Tue 06/11/13 23:52:11 DSP      LOG             0 P Ratio = 5.6, 25.1
Tue 06/11/13 23:52:11 DSP      LOG             0 Printing Layer 326 of 764
Tue 06/11/13 23:52:43 DSP      LOG             0 Printing Layer 327 of 764
Tue 06/11/13 23:53:14 DSP      LOG             0 Printing Layer 328 of 764
Tue 06/11/13 23:53:45 DSP      LOG             0 Printing Layer 329 of 764
Tue 06/11/13 23:54:12 DSP      LOCAL_LOG       0 Support Pump Pos=0.627; Vacuum=4.561; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=534 sec; MPixels/Sec=0.000000
Tue 06/11/13 23:54:19 DSP      LOG             0 Printing Layer 330 of 764
Tue 06/11/13 23:54:50 DSP      LOG             0 Printing Layer 331 of 764
Tue 06/11/13 23:55:21 DSP      LOG             0 Printing Layer 332 of 764
Tue 06/11/13 23:55:53 DSP      LOG             0 Printing Layer 333 of 764
Tue 06/11/13 23:56:24 DSP      LOG             0 Printing Layer 334 of 764
Tue 06/11/13 23:56:55 DSP      LOG             0 Printing Layer 335 of 764
Tue 06/11/13 23:57:27 DSP      LOG             0 Printing Layer 336 of 764
Tue 06/11/13 23:57:58 DSP      LOG             0 Printing Layer 337 of 764
Tue 06/11/13 23:58:29 DSP      LOG             0 Printing Layer 338 of 764
Tue 06/11/13 23:59:01 DSP      LOG             0 Printing Layer 339 of 764
Tue 06/11/13 23:59:32 DSP      LOG             0 Printing Layer 340 of 764
Wed 06/12/13 00:00:03 DSP      LOG             0 Printing Layer 341 of 764
Wed 06/12/13 00:00:35 DSP      LOG             0 Printing Layer 342 of 764
Wed 06/12/13 00:01:06 DSP      LOG             0 Printing Layer 343 of 764
Wed 06/12/13 00:01:37 DSP      LOG             0 Printing Layer 344 of 764
Wed 06/12/13 00:02:09 DSP      LOG             0 Printing Layer 345 of 764
Wed 06/12/13 00:02:33 DSP      LOCAL_LOG       0 Support Pump Pos=0.652; Vacuum=4.550; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=502 sec; MPixels/Sec=0.000000
Wed 06/12/13 00:02:40 DSP      LOG             0 Printing Layer 346 of 764
Wed 06/12/13 00:03:11 DSP      LOG             0 Printing Layer 347 of 764
Wed 06/12/13 00:03:43 DSP      LOG             0 Printing Layer 348 of 764
Wed 06/12/13 00:04:14 DSP      LOG             0 Printing Layer 349 of 764
Wed 06/12/13 00:04:45 DSP      LOG             0 Printing Layer 350 of 764
Wed 06/12/13 00:05:17 DSP      LOG             0 S Ratio = 38.5, 51.1
Wed 06/12/13 00:05:17 DSP      LOG             0 Printing Layer 351 of 764
Wed 06/12/13 00:05:50 DSP      LOG             0 Printing Layer 352 of 764
Wed 06/12/13 00:06:21 DSP      LOG             0 Printing Layer 353 of 764
Wed 06/12/13 00:06:53 DSP      LOG             0 Printing Layer 354 of 764
Wed 06/12/13 00:07:24 DSP      LOG             0 Printing Layer 355 of 764
Wed 06/12/13 00:07:55 DSP      LOG             0 Printing Layer 356 of 764
Wed 06/12/13 00:08:27 DSP      LOG             0 Printing Layer 357 of 764
Wed 06/12/13 00:08:58 DSP      LOG             0 Printing Layer 358 of 764
Wed 06/12/13 00:09:29 DSP      LOG             0 Printing Layer 359 of 764
Wed 06/12/13 00:10:01 DSP      LOG             0 Printing Layer 360 of 764
Wed 06/12/13 00:10:03 DSP      LOCAL_LOG       0 Support Pump Pos=0.677; Vacuum=4.572; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=450 sec; MPixels/Sec=0.000000
Wed 06/12/13 00:10:32 DSP      LOG             0 Printing Layer 361 of 764
Wed 06/12/13 00:11:03 DSP      LOG             0 Printing Layer 362 of 764
Wed 06/12/13 00:11:35 DSP      LOG             0 Printing Layer 363 of 764
Wed 06/12/13 00:12:06 DSP      LOG             0 Printing Layer 364 of 764
Wed 06/12/13 00:12:37 DSP      LOG             0 Printing Layer 365 of 764
Wed 06/12/13 00:13:09 DSP      LOG             0 Printing Layer 366 of 764
Wed 06/12/13 00:13:40 DSP      LOG             0 Printing Layer 367 of 764
Wed 06/12/13 00:14:11 DSP      LOG             0 Printing Layer 368 of 764
Wed 06/12/13 00:14:43 DSP      LOG             0 Printing Layer 369 of 764
Wed 06/12/13 00:15:14 DSP      LOG             0 Printing Layer 370 of 764
Wed 06/12/13 00:15:45 DSP      LOG             0 Printing Layer 371 of 764
Wed 06/12/13 00:16:17 DSP      LOG             0 Printing Layer 372 of 764
Wed 06/12/13 00:16:40 DEBUG    NOTICE         0 Bag Heater Off
Wed 06/12/13 00:16:50 DSP      LOG             0 Printing Layer 373 of 764
Wed 06/12/13 00:17:22 DSP      LOG             0 Printing Layer 374 of 764
Wed 06/12/13 00:17:53 DSP      LOG             0 Printing Layer 375 of 764
Wed 06/12/13 00:18:24 DSP      LOG             0 S Ratio = 71.6, 55.9
Wed 06/12/13 00:18:24 DSP      LOG             0 Printing Layer 376 of 764
Wed 06/12/13 00:18:56 DSP      LOG             0 Printing Layer 377 of 764
Wed 06/12/13 00:19:27 DSP      LOG             0 Printing Layer 378 of 764
Wed 06/12/13 00:19:58 DSP      LOG             0 Printing Layer 379 of 764
Wed 06/12/13 00:20:22 DSP      LOCAL_LOG       0 Support Pump Pos=0.702; Vacuum=4.575; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=619 sec; MPixels/Sec=0.000000
Wed 06/12/13 00:20:29 DSP      LOG             0 Printing Layer 380 of 764
Wed 06/12/13 00:21:01 DSP      LOG             0 Printing Layer 381 of 764
Wed 06/12/13 00:21:32 DSP      LOG             0 Printing Layer 382 of 764
Wed 06/12/13 00:22:03 DSP      LOG             0 Printing Layer 383 of 764
Wed 06/12/13 00:22:35 DSP      LOG             0 Printing Layer 384 of 764
Wed 06/12/13 00:22:59 DSP      LOCAL_LOG       0 Part Pump Pos=1.027; Vacuum=4.572; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=1982 sec; MPixels/Sec=0.000000
Wed 06/12/13 00:23:02 DSP      LOCAL_LOG       0 Part Pump Pos=1.027; Vacuum=4.572; Cnt=2
Wed 06/12/13 00:23:04 DSP      LOCAL_LOG       0 Part Pump Pos=1.027; Vacuum=4.519; Cnt=3
Wed 06/12/13 00:23:06 DSP      LOG             0 Printing Layer 385 of 764
Wed 06/12/13 00:23:37 DSP      LOG             0 Printing Layer 386 of 764
Wed 06/12/13 00:24:09 DSP      LOG             0 Printing Layer 387 of 764
Wed 06/12/13 00:24:40 DSP      LOG             0 Printing Layer 388 of 764
Wed 06/12/13 00:25:12 DSP      LOG             0 Printing Layer 389 of 764
Wed 06/12/13 00:25:43 DSP      LOG             0 Printing Layer 390 of 764
Wed 06/12/13 00:26:14 DSP      LOG             0 Printing Layer 391 of 764
Wed 06/12/13 00:26:46 DSP      LOG             0 Printing Layer 392 of 764
Wed 06/12/13 00:27:17 DSP      LOG             0 Printing Layer 393 of 764
Wed 06/12/13 00:27:48 DSP      LOG             0 Printing Layer 394 of 764
Wed 06/12/13 00:28:22 DSP      LOG             0 Printing Layer 395 of 764
Wed 06/12/13 00:28:53 DSP      LOG             0 Printing Layer 396 of 764
Wed 06/12/13 00:29:16 DSP      LOCAL_LOG       0 Support Pump Pos=0.727; Vacuum=4.570; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=534 sec; MPixels/Sec=0.000000
Wed 06/12/13 00:29:24 DSP      LOG             0 Printing Layer 397 of 764
Wed 06/12/13 00:29:56 DSP      LOG             0 Printing Layer 398 of 764
Wed 06/12/13 00:30:27 DSP      LOG             0 Printing Layer 399 of 764
Wed 06/12/13 00:30:58 DSP      LOG             0 Printing Layer 400 of 764
Wed 06/12/13 00:31:30 DSP      LOG             0 S Ratio = 34.9, 53.6
Wed 06/12/13 00:31:30 DSP      LOG             0 P Ratio = 13.1, 21.7
Wed 06/12/13 00:31:30 DSP      LOG             0 Printing Layer 401 of 764
Wed 06/12/13 00:32:01 DSP      LOG             0 Printing Layer 402 of 764
Wed 06/12/13 00:32:32 DSP      LOG             0 Printing Layer 403 of 764
Wed 06/12/13 00:33:04 DSP      LOG             0 Printing Layer 404 of 764
Wed 06/12/13 00:33:35 DSP      LOG             0 Printing Layer 405 of 764
Wed 06/12/13 00:34:07 DSP      LOG             0 Printing Layer 406 of 764
Wed 06/12/13 00:34:38 DSP      LOG             0 Printing Layer 407 of 764
Wed 06/12/13 00:35:09 DSP      LOG             0 Printing Layer 408 of 764
Wed 06/12/13 00:35:41 DSP      LOG             0 Printing Layer 409 of 764
Wed 06/12/13 00:36:12 DSP      LOG             0 Printing Layer 410 of 764
Wed 06/12/13 00:36:43 DSP      LOG             0 Printing Layer 411 of 764
Wed 06/12/13 00:37:15 DSP      LOG             0 Printing Layer 412 of 764
Wed 06/12/13 00:37:46 DSP      LOG             0 Printing Layer 413 of 764
Wed 06/12/13 00:38:17 DSP      LOG             0 Printing Layer 414 of 764
Wed 06/12/13 00:38:49 DSP      LOG             0 Printing Layer 415 of 764
Wed 06/12/13 00:39:20 DSP      LOG             0 Printing Layer 416 of 764
Wed 06/12/13 00:39:46 DSP      LOCAL_LOG       0 Support Pump Pos=0.752; Vacuum=4.550; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=630 sec; MPixels/Sec=0.000000
Wed 06/12/13 00:39:54 DSP      LOG             0 Printing Layer 417 of 764
Wed 06/12/13 00:40:25 DSP      LOG             0 Printing Layer 418 of 764
Wed 06/12/13 00:40:56 DSP      LOG             0 Printing Layer 419 of 764
Wed 06/12/13 00:41:27 DSP      LOG             0 Printing Layer 420 of 764
Wed 06/12/13 00:41:59 DSP      LOG             0 Printing Layer 421 of 764
Wed 06/12/13 00:42:30 DSP      LOG             0 Printing Layer 422 of 764
Wed 06/12/13 00:43:01 DSP      LOG             0 Printing Layer 423 of 764
Wed 06/12/13 00:43:33 DSP      LOG             0 Printing Layer 424 of 764
Wed 06/12/13 00:44:04 DSP      LOG             0 Printing Layer 425 of 764
Wed 06/12/13 00:44:35 DSP      LOG             0 S Ratio = 66.9, 58.6
Wed 06/12/13 00:44:35 DSP      LOG             0 Printing Layer 426 of 764
Wed 06/12/13 00:45:07 DSP      LOG             0 Printing Layer 427 of 764
Wed 06/12/13 00:45:38 DSP      LOG             0 Printing Layer 428 of 764
Wed 06/12/13 00:46:09 DSP      LOG             0 Printing Layer 429 of 764
Wed 06/12/13 00:46:41 DSP      LOG             0 Printing Layer 430 of 764
Wed 06/12/13 00:46:41 DEBUG    NOTICE         0 Bag Heater On
Wed 06/12/13 00:47:12 DSP      LOG             0 Printing Layer 431 of 764
Wed 06/12/13 00:47:43 DSP      LOG             0 Printing Layer 432 of 764
Wed 06/12/13 00:48:07 DSP      LOCAL_LOG       0 Support Pump Pos=0.777; Vacuum=4.575; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=501 sec; MPixels/Sec=0.000000
Wed 06/12/13 00:48:15 DSP      LOG             0 Printing Layer 433 of 764
Wed 06/12/13 00:48:46 DSP      LOG             0 Printing Layer 434 of 764
Wed 06/12/13 00:49:17 DSP      LOG             0 Printing Layer 435 of 764
Wed 06/12/13 00:49:49 DSP      LOG             0 Printing Layer 436 of 764
Wed 06/12/13 00:50:20 DSP      LOG             0 Printing Layer 437 of 764
Wed 06/12/13 00:50:52 DSP      LOG             0 Printing Layer 438 of 764
Wed 06/12/13 00:51:25 DSP      LOG             0 Printing Layer 439 of 764
Wed 06/12/13 00:51:56 DSP      LOG             0 Printing Layer 440 of 764
Wed 06/12/13 00:52:28 DSP      LOG             0 Printing Layer 441 of 764
Wed 06/12/13 00:52:59 DSP      LOG             0 Printing Layer 442 of 764
Wed 06/12/13 00:53:30 DSP      LOG             0 Printing Layer 443 of 764
Wed 06/12/13 00:54:01 DSP      LOG             0 Printing Layer 444 of 764
Wed 06/12/13 00:54:33 DSP      LOG             0 Printing Layer 445 of 764
Wed 06/12/13 00:55:04 DSP      LOG             0 Printing Layer 446 of 764
Wed 06/12/13 00:55:35 DSP      LOG             0 Printing Layer 447 of 764
Wed 06/12/13 00:56:07 DSP      LOG             0 Printing Layer 448 of 764
Wed 06/12/13 00:56:38 DSP      LOG             0 Printing Layer 449 of 764
Wed 06/12/13 00:57:09 DSP      LOG             0 Printing Layer 450 of 764
Wed 06/12/13 00:57:41 DSP      LOG             0 S Ratio = 59.0, 54.2
Wed 06/12/13 00:57:41 DSP      LOG             0 Printing Layer 451 of 764
Wed 06/12/13 00:58:12 DSP      LOG             0 Printing Layer 452 of 764
Wed 06/12/13 00:58:43 DSP      LOG             0 Printing Layer 453 of 764
Wed 06/12/13 00:59:15 DSP      LOG             0 Printing Layer 454 of 764
Wed 06/12/13 00:59:46 DSP      LOG             0 Printing Layer 455 of 764
Wed 06/12/13 01:00:17 DSP      LOG             0 Printing Layer 456 of 764
Wed 06/12/13 01:00:49 DSP      LOG             0 Printing Layer 457 of 764
Wed 06/12/13 01:01:20 DSP      LOG             0 Printing Layer 458 of 764
Wed 06/12/13 01:01:52 DSP      LOG             0 Printing Layer 459 of 764
Wed 06/12/13 01:02:23 DSP      LOG             0 Printing Layer 460 of 764
Wed 06/12/13 01:02:49 DSP      LOCAL_LOG       0 Support Pump Pos=0.802; Vacuum=4.586; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=882 sec; MPixels/Sec=0.000000
Wed 06/12/13 01:02:56 DSP      LOG             0 Printing Layer 461 of 764
Wed 06/12/13 01:03:28 DSP      LOG             0 Printing Layer 462 of 764
Wed 06/12/13 01:03:59 DSP      LOG             0 Printing Layer 463 of 764
Wed 06/12/13 01:04:30 DSP      LOG             0 Printing Layer 464 of 764
Wed 06/12/13 01:05:01 DSP      LOG             0 Printing Layer 465 of 764
Wed 06/12/13 01:05:33 DSP      LOG             0 Printing Layer 466 of 764
Wed 06/12/13 01:06:04 DSP      LOG             0 Printing Layer 467 of 764
Wed 06/12/13 01:06:27 DSP      LOCAL_LOG       0 Part Pump Pos=1.102; Vacuum=4.536; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=2608 sec; MPixels/Sec=0.000000
Wed 06/12/13 01:06:29 DSP      LOCAL_LOG       0 Part Pump Pos=1.102; Vacuum=4.600; Cnt=2
Wed 06/12/13 01:06:32 DSP      LOCAL_LOG       0 Part Pump Pos=1.102; Vacuum=4.522; Cnt=3
Wed 06/12/13 01:06:35 DSP      LOCAL_LOG       0 Part Pump Pos=1.102; Vacuum=4.589; Cnt=4
Wed 06/12/13 01:06:35 DSP      LOG             0 Printing Layer 468 of 764
Wed 06/12/13 01:07:07 DSP      LOG             0 Printing Layer 469 of 764
Wed 06/12/13 01:07:38 DSP      LOG             0 Printing Layer 470 of 764
Wed 06/12/13 01:08:09 DSP      LOG             0 Printing Layer 471 of 764
Wed 06/12/13 01:08:41 DSP      LOG             0 Printing Layer 472 of 764
Wed 06/12/13 01:09:12 DSP      LOG             0 Printing Layer 473 of 764
Wed 06/12/13 01:09:43 DSP      LOG             0 Printing Layer 474 of 764
Wed 06/12/13 01:10:15 DSP      LOG             0 Printing Layer 475 of 764
Wed 06/12/13 01:10:46 DSP      LOG             0 S Ratio = 43.1, 55.1
Wed 06/12/13 01:10:46 DSP      LOG             0 P Ratio = 12.7, 18.3
Wed 06/12/13 01:10:46 DSP      LOG             0 Printing Layer 476 of 764
Wed 06/12/13 01:11:17 DSP      LOG             0 Printing Layer 477 of 764
Wed 06/12/13 01:11:49 DSP      LOG             0 Printing Layer 478 of 764
Wed 06/12/13 01:12:20 DSP      LOG             0 Printing Layer 479 of 764
Wed 06/12/13 01:12:51 DSP      LOG             0 Printing Layer 480 of 764
Wed 06/12/13 01:13:23 DSP      LOG             0 Printing Layer 481 of 764
Wed 06/12/13 01:13:54 DSP      LOG             0 Printing Layer 482 of 764
Wed 06/12/13 01:14:28 DSP      LOG             0 Printing Layer 483 of 764
Wed 06/12/13 01:14:59 DSP      LOG             0 Printing Layer 484 of 764
Wed 06/12/13 01:15:30 DSP      LOG             0 Printing Layer 485 of 764
Wed 06/12/13 01:16:02 DSP      LOG             0 Printing Layer 486 of 764
Wed 06/12/13 01:16:33 DSP      LOG             0 Printing Layer 487 of 764
Wed 06/12/13 01:16:42 DEBUG    NOTICE         0 Bag Heater Off
Wed 06/12/13 01:17:05 DSP      LOG             0 Printing Layer 488 of 764
Wed 06/12/13 01:17:36 DSP      LOG             0 Printing Layer 489 of 764
Wed 06/12/13 01:18:07 DSP      LOG             0 Printing Layer 490 of 764
Wed 06/12/13 01:18:39 DSP      LOG             0 Printing Layer 491 of 764
Wed 06/12/13 01:19:10 DSP      LOG             0 Printing Layer 492 of 764
Wed 06/12/13 01:19:41 DSP      LOG             0 Printing Layer 493 of 764
Wed 06/12/13 01:20:13 DSP      LOG             0 Printing Layer 494 of 764
Wed 06/12/13 01:20:44 DSP      LOG             0 Printing Layer 495 of 764
Wed 06/12/13 01:21:08 DSP      LOCAL_LOG       0 Support Pump Pos=0.827; Vacuum=4.578; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=1099 sec; MPixels/Sec=0.000000
Wed 06/12/13 01:21:15 DSP      LOG             0 Printing Layer 496 of 764
Wed 06/12/13 01:21:47 DSP      LOG             0 Printing Layer 497 of 764
Wed 06/12/13 01:22:18 DSP      LOG             0 Printing Layer 498 of 764
Wed 06/12/13 01:22:50 DSP      LOG             0 Printing Layer 499 of 764
Wed 06/12/13 01:23:21 DSP      LOG             0 Printing Layer 500 of 764
Wed 06/12/13 01:23:52 DSP      LOG             0 S Ratio = 30.1, 46.8
Wed 06/12/13 01:23:52 DSP      LOG             0 Printing Layer 501 of 764
Wed 06/12/13 01:24:24 DSP      LOG             0 Printing Layer 502 of 764
Wed 06/12/13 01:24:55 DSP      LOG             0 Printing Layer 503 of 764
Wed 06/12/13 01:25:29 DSP      LOG             0 Printing Layer 504 of 764
Wed 06/12/13 01:26:00 DSP      LOG             0 Printing Layer 505 of 764
Wed 06/12/13 01:26:31 DSP      LOG             0 Printing Layer 506 of 764
Wed 06/12/13 01:27:03 DSP      LOG             0 Printing Layer 507 of 764
Wed 06/12/13 01:27:34 DSP      LOG             0 Printing Layer 508 of 764
Wed 06/12/13 01:28:05 DSP      LOG             0 Printing Layer 509 of 764
Wed 06/12/13 01:28:36 DSP      LOG             0 Printing Layer 510 of 764
Wed 06/12/13 01:29:08 DSP      LOG             0 Printing Layer 511 of 764
Wed 06/12/13 01:29:39 DSP      LOG             0 Printing Layer 512 of 764
Wed 06/12/13 01:30:10 DSP      LOG             0 Printing Layer 513 of 764
Wed 06/12/13 01:30:42 DSP      LOG             0 Printing Layer 514 of 764
Wed 06/12/13 01:31:13 DSP      LOG             0 Printing Layer 515 of 764
Wed 06/12/13 01:31:45 DSP      LOG             0 Printing Layer 516 of 764
Wed 06/12/13 01:32:16 DSP      LOG             0 Printing Layer 517 of 764
Wed 06/12/13 01:32:47 DSP      LOG             0 Printing Layer 518 of 764
Wed 06/12/13 01:33:19 DSP      LOG             0 Printing Layer 519 of 764
Wed 06/12/13 01:33:50 DSP      LOG             0 Printing Layer 520 of 764
Wed 06/12/13 01:34:21 DSP      LOG             0 Printing Layer 521 of 764
Wed 06/12/13 01:34:53 DSP      LOG             0 Printing Layer 522 of 764
Wed 06/12/13 01:35:24 DSP      LOG             0 Printing Layer 523 of 764
Wed 06/12/13 01:35:55 DSP      LOG             0 Printing Layer 524 of 764
Wed 06/12/13 01:36:27 DSP      LOG             0 Printing Layer 525 of 764
Wed 06/12/13 01:37:00 DSP      LOG             0 Printing Layer 526 of 764
Wed 06/12/13 01:37:32 DSP      LOG             0 Printing Layer 527 of 764
Wed 06/12/13 01:38:03 DSP      LOG             0 Printing Layer 528 of 764
Wed 06/12/13 01:38:34 DSP      LOG             0 Printing Layer 529 of 764
Wed 06/12/13 01:39:05 DSP      LOG             0 Printing Layer 530 of 764
Wed 06/12/13 01:39:37 DSP      LOG             0 Printing Layer 531 of 764
Wed 06/12/13 01:40:08 DSP      LOG             0 Printing Layer 532 of 764
Wed 06/12/13 01:40:39 DSP      LOG             0 Printing Layer 533 of 764
Wed 06/12/13 01:41:11 DSP      LOG             0 Printing Layer 534 of 764
Wed 06/12/13 01:41:42 DSP      LOG             0 Printing Layer 535 of 764
Wed 06/12/13 01:42:13 DSP      LOG             0 Printing Layer 536 of 764
Wed 06/12/13 01:42:45 DSP      LOG             0 Printing Layer 537 of 764
Wed 06/12/13 01:43:16 DSP      LOG             0 Printing Layer 538 of 764
Wed 06/12/13 01:43:47 DSP      LOG             0 Printing Layer 539 of 764
Wed 06/12/13 01:44:11 DSP      LOCAL_LOG       0 Support Pump Pos=0.852; Vacuum=4.550; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=1383 sec; MPixels/Sec=0.000000
Wed 06/12/13 01:44:19 DSP      LOG             0 Printing Layer 540 of 764
Wed 06/12/13 01:44:50 DSP      LOG             0 Printing Layer 541 of 764
Wed 06/12/13 01:45:21 DSP      LOG             0 Printing Layer 542 of 764
Wed 06/12/13 01:45:53 DSP      LOG             0 Printing Layer 543 of 764
Wed 06/12/13 01:46:24 DSP      LOG             0 Printing Layer 544 of 764
Wed 06/12/13 01:46:43 DEBUG    NOTICE         0 Bag Heater On
Wed 06/12/13 01:46:55 DSP      LOG             0 Printing Layer 545 of 764
Wed 06/12/13 01:47:27 DSP      LOG             0 Printing Layer 546 of 764
Wed 06/12/13 01:47:58 DSP      LOG             0 Printing Layer 547 of 764
Wed 06/12/13 01:48:32 DSP      LOG             0 Printing Layer 548 of 764
Wed 06/12/13 01:49:03 DSP      LOG             0 Printing Layer 549 of 764
Wed 06/12/13 01:49:34 DSP      LOG             0 Printing Layer 550 of 764
Wed 06/12/13 01:50:05 DSP      LOG             0 S Ratio = 19.3, 43.7
Wed 06/12/13 01:50:06 DSP      LOG             0 Printing Layer 551 of 764
Wed 06/12/13 01:50:37 DSP      LOG             0 Printing Layer 552 of 764
Wed 06/12/13 01:51:08 DSP      LOG             0 Printing Layer 553 of 764
Wed 06/12/13 01:51:39 DSP      LOG             0 Printing Layer 554 of 764
Wed 06/12/13 01:52:11 DSP      LOG             0 Printing Layer 555 of 764
Wed 06/12/13 01:52:42 DSP      LOG             0 Printing Layer 556 of 764
Wed 06/12/13 01:53:13 DSP      LOG             0 Printing Layer 557 of 764
Wed 06/12/13 01:53:45 DSP      LOG             0 Printing Layer 558 of 764
Wed 06/12/13 01:54:16 DSP      LOG             0 Printing Layer 559 of 764
Wed 06/12/13 01:54:48 DSP      LOG             0 Printing Layer 560 of 764
Wed 06/12/13 01:55:19 DSP      LOG             0 Printing Layer 561 of 764
Wed 06/12/13 01:55:50 DSP      LOG             0 Printing Layer 562 of 764
Wed 06/12/13 01:56:21 DSP      LOG             0 Printing Layer 563 of 764
Wed 06/12/13 01:56:53 DSP      LOG             0 Printing Layer 564 of 764
Wed 06/12/13 01:57:24 DSP      LOG             0 Printing Layer 565 of 764
Wed 06/12/13 01:57:55 DSP      LOG             0 Printing Layer 566 of 764
Wed 06/12/13 01:58:27 DSP      LOG             0 Printing Layer 567 of 764
Wed 06/12/13 01:58:58 DSP      LOG             0 Printing Layer 568 of 764
Wed 06/12/13 01:59:29 DSP      LOG             0 Printing Layer 569 of 764
Wed 06/12/13 02:00:03 DSP      LOG             0 Printing Layer 570 of 764
Wed 06/12/13 02:00:34 DSP      LOG             0 Printing Layer 571 of 764
Wed 06/12/13 02:01:05 DSP      LOG             0 Printing Layer 572 of 764
Wed 06/12/13 02:01:36 DSP      LOG             0 Printing Layer 573 of 764
Wed 06/12/13 02:02:00 DSP      LOCAL_LOG       0 Part Pump Pos=1.202; Vacuum=4.572; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=3333 sec; MPixels/Sec=0.000000
Wed 06/12/13 02:02:03 DSP      LOCAL_LOG       0 Part Pump Pos=1.202; Vacuum=4.556; Cnt=2
Wed 06/12/13 02:02:06 DSP      LOCAL_LOG       0 Part Pump Pos=1.202; Vacuum=4.497; Cnt=3
Wed 06/12/13 02:02:07 DSP      LOG             0 Printing Layer 574 of 764
Wed 06/12/13 02:02:39 DSP      LOG             0 Printing Layer 575 of 764
Wed 06/12/13 02:03:10 DSP      LOG             0 P Ratio = 6.1, 13.5
Wed 06/12/13 02:03:10 DSP      LOG             0 Printing Layer 576 of 764
Wed 06/12/13 02:03:41 DSP      LOG             0 Printing Layer 577 of 764
Wed 06/12/13 02:04:13 DSP      LOG             0 Printing Layer 578 of 764
Wed 06/12/13 02:04:44 DSP      LOG             0 Printing Layer 579 of 764
Wed 06/12/13 02:05:15 DSP      LOG             0 Printing Layer 580 of 764
Wed 06/12/13 02:05:47 DSP      LOG             0 Printing Layer 581 of 764
Wed 06/12/13 02:06:18 DSP      LOG             0 Printing Layer 582 of 764
Wed 06/12/13 02:06:50 DSP      LOG             0 Printing Layer 583 of 764
Wed 06/12/13 02:07:21 DSP      LOG             0 Printing Layer 584 of 764
Wed 06/12/13 02:07:53 DSP      LOG             0 Printing Layer 585 of 764
Wed 06/12/13 02:08:24 DSP      LOG             0 Printing Layer 586 of 764
Wed 06/12/13 02:08:55 DSP      LOG             0 Printing Layer 587 of 764
Wed 06/12/13 02:09:27 DSP      LOG             0 Printing Layer 588 of 764
Wed 06/12/13 02:09:58 DSP      LOG             0 Printing Layer 589 of 764
Wed 06/12/13 02:10:30 DSP      LOG             0 Printing Layer 590 of 764
Wed 06/12/13 02:11:01 DSP      LOG             0 Printing Layer 591 of 764
Wed 06/12/13 02:11:35 DSP      LOG             0 Printing Layer 592 of 764
Wed 06/12/13 02:12:06 DSP      LOG             0 Printing Layer 593 of 764
Wed 06/12/13 02:12:37 DSP      LOG             0 Printing Layer 594 of 764
Wed 06/12/13 02:13:09 DSP      LOG             0 Printing Layer 595 of 764
Wed 06/12/13 02:13:40 DSP      LOG             0 Printing Layer 596 of 764
Wed 06/12/13 02:14:11 DSP      LOG             0 Printing Layer 597 of 764
Wed 06/12/13 02:14:43 DSP      LOG             0 Printing Layer 598 of 764
Wed 06/12/13 02:15:14 DSP      LOG             0 Printing Layer 599 of 764
Wed 06/12/13 02:15:45 DSP      LOG             0 Printing Layer 600 of 764
Wed 06/12/13 02:16:17 DSP      LOG             0 Printing Layer 601 of 764
Wed 06/12/13 02:16:44 DEBUG    NOTICE         0 Bag Heater Off
Wed 06/12/13 02:16:48 DSP      LOG             0 Printing Layer 602 of 764
Wed 06/12/13 02:17:20 DSP      LOG             0 Printing Layer 603 of 764
Wed 06/12/13 02:17:51 DSP      LOG             0 Printing Layer 604 of 764
Wed 06/12/13 02:18:23 DSP      LOG             0 Printing Layer 605 of 764
Wed 06/12/13 02:18:54 DSP      LOG             0 Printing Layer 606 of 764
Wed 06/12/13 02:19:26 DSP      LOG             0 Printing Layer 607 of 764
Wed 06/12/13 02:19:57 DSP      LOG             0 Printing Layer 608 of 764
Wed 06/12/13 02:20:28 DSP      LOG             0 Printing Layer 609 of 764
Wed 06/12/13 02:20:59 DSP      LOG             0 Printing Layer 610 of 764
Wed 06/12/13 02:21:31 DSP      LOG             0 Printing Layer 611 of 764
Wed 06/12/13 02:22:02 DSP      LOG             0 Printing Layer 612 of 764
Wed 06/12/13 02:22:35 DSP      LOG             0 Printing Layer 613 of 764
Wed 06/12/13 02:23:06 DSP      LOG             0 Printing Layer 614 of 764
Wed 06/12/13 02:23:37 DSP      LOG             0 Printing Layer 615 of 764
Wed 06/12/13 02:24:09 DSP      LOG             0 Printing Layer 616 of 764
Wed 06/12/13 02:24:41 DSP      LOG             0 Printing Layer 617 of 764
Wed 06/12/13 02:25:12 DSP      LOG             0 Printing Layer 618 of 764
Wed 06/12/13 02:25:44 DSP      LOG             0 Printing Layer 619 of 764
Wed 06/12/13 02:26:16 DSP      LOG             0 Printing Layer 620 of 764
Wed 06/12/13 02:26:48 DSP      LOG             0 Printing Layer 621 of 764
Wed 06/12/13 02:27:19 DSP      LOG             0 Printing Layer 622 of 764
Wed 06/12/13 02:27:51 DSP      LOG             0 Printing Layer 623 of 764
Wed 06/12/13 02:28:23 DSP      LOG             0 Printing Layer 624 of 764
Wed 06/12/13 02:28:54 DSP      LOG             0 Printing Layer 625 of 764
Wed 06/12/13 02:29:26 DSP      LOG             0 Printing Layer 626 of 764
Wed 06/12/13 02:29:58 DSP      LOG             0 Printing Layer 627 of 764
Wed 06/12/13 02:30:30 DSP      LOG             0 Printing Layer 628 of 764
Wed 06/12/13 02:31:01 DSP      LOG             0 Printing Layer 629 of 764
Wed 06/12/13 02:31:33 DSP      LOG             0 Printing Layer 630 of 764
Wed 06/12/13 02:32:05 DSP      LOG             0 Printing Layer 631 of 764
Wed 06/12/13 02:32:37 DSP      LOG             0 Printing Layer 632 of 764
Wed 06/12/13 02:33:08 DSP      LOG             0 Printing Layer 633 of 764
Wed 06/12/13 02:33:40 DSP      LOG             0 Printing Layer 634 of 764
Wed 06/12/13 02:34:14 DSP      LOG             0 Printing Layer 635 of 764
Wed 06/12/13 02:34:45 DSP      LOG             0 Printing Layer 636 of 764
Wed 06/12/13 02:35:17 DSP      LOG             0 Printing Layer 637 of 764
Wed 06/12/13 02:35:40 DSP      LOCAL_LOG       0 Support Pump Pos=0.877; Vacuum=4.558; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=3089 sec; MPixels/Sec=0.000000
Wed 06/12/13 02:35:48 DSP      LOG             0 Printing Layer 638 of 764
Wed 06/12/13 02:36:19 DSP      LOG             0 Printing Layer 639 of 764
Wed 06/12/13 02:36:51 DSP      LOG             0 Printing Layer 640 of 764
Wed 06/12/13 02:37:22 DSP      LOG             0 Printing Layer 641 of 764
Wed 06/12/13 02:37:53 DSP      LOG             0 Printing Layer 642 of 764
Wed 06/12/13 02:38:25 DSP      LOG             0 Printing Layer 643 of 764
Wed 06/12/13 02:38:56 DSP      LOG             0 Printing Layer 644 of 764
Wed 06/12/13 02:39:28 DSP      LOG             0 Printing Layer 645 of 764
Wed 06/12/13 02:39:58 DSP      LOG             0 Printing Layer 646 of 764
Wed 06/12/13 02:40:28 DSP      LOG             0 Printing Layer 647 of 764
Wed 06/12/13 02:40:59 DSP      LOG             0 Printing Layer 648 of 764
Wed 06/12/13 02:41:29 DSP      LOG             0 Printing Layer 649 of 764
Wed 06/12/13 02:41:59 DSP      LOG             0 Printing Layer 650 of 764
Wed 06/12/13 02:42:29 DSP      LOG             0 S Ratio = 7.1, 31.7
Wed 06/12/13 02:42:29 DSP      LOG             0 Printing Layer 651 of 764
Wed 06/12/13 02:43:00 DSP      LOG             0 Printing Layer 652 of 764
Wed 06/12/13 02:43:30 DSP      LOG             0 Printing Layer 653 of 764
Wed 06/12/13 02:44:00 DSP      LOG             0 Printing Layer 654 of 764
Wed 06/12/13 02:44:30 DSP      LOG             0 Printing Layer 655 of 764
Wed 06/12/13 02:45:01 DSP      LOG             0 Printing Layer 656 of 764
Wed 06/12/13 02:45:33 DSP      LOG             0 Printing Layer 657 of 764
Wed 06/12/13 02:46:03 DSP      LOG             0 Printing Layer 658 of 764
Wed 06/12/13 02:46:33 DSP      LOG             0 Printing Layer 659 of 764
Wed 06/12/13 02:46:45 DEBUG    NOTICE         0 Bag Heater On
Wed 06/12/13 02:47:03 DSP      LOG             0 Printing Layer 660 of 764
Wed 06/12/13 02:47:34 DSP      LOG             0 Printing Layer 661 of 764
Wed 06/12/13 02:48:04 DSP      LOG             0 Printing Layer 662 of 764
Wed 06/12/13 02:48:34 DSP      LOG             0 Printing Layer 663 of 764
Wed 06/12/13 02:49:04 DSP      LOG             0 Printing Layer 664 of 764
Wed 06/12/13 02:49:34 DSP      LOG             0 Printing Layer 665 of 764
Wed 06/12/13 02:50:04 DSP      LOG             0 Printing Layer 666 of 764
Wed 06/12/13 02:50:35 DSP      LOG             0 Printing Layer 667 of 764
Wed 06/12/13 02:51:05 DSP      LOG             0 Printing Layer 668 of 764
Wed 06/12/13 02:51:35 DSP      LOG             0 Printing Layer 669 of 764
Wed 06/12/13 02:52:05 DSP      LOG             0 Printing Layer 670 of 764
Wed 06/12/13 02:52:35 DSP      LOG             0 Printing Layer 671 of 764
Wed 06/12/13 02:53:05 DSP      LOG             0 Printing Layer 672 of 764
Wed 06/12/13 02:53:35 DSP      LOG             0 Printing Layer 673 of 764
Wed 06/12/13 02:54:05 DSP      LOG             0 Printing Layer 674 of 764
Wed 06/12/13 02:54:36 DSP      LOG             0 Printing Layer 675 of 764
Wed 06/12/13 02:55:06 DSP      LOG             0 Printing Layer 676 of 764
Wed 06/12/13 02:55:36 DSP      LOG             0 Printing Layer 677 of 764
Wed 06/12/13 02:56:06 DSP      LOG             0 Printing Layer 678 of 764
Wed 06/12/13 02:56:38 DSP      LOG             0 Printing Layer 679 of 764
Wed 06/12/13 02:57:08 DSP      LOG             0 Printing Layer 680 of 764
Wed 06/12/13 02:57:38 DSP      LOG             0 Printing Layer 681 of 764
Wed 06/12/13 02:58:08 DSP      LOG             0 Printing Layer 682 of 764
Wed 06/12/13 02:58:38 DSP      LOG             0 Printing Layer 683 of 764
Wed 06/12/13 02:59:08 DSP      LOG             0 Printing Layer 684 of 764
Wed 06/12/13 02:59:38 DSP      LOG             0 Printing Layer 685 of 764
Wed 06/12/13 03:00:08 DSP      LOG             0 Printing Layer 686 of 764
Wed 06/12/13 03:00:38 DSP      LOG             0 Printing Layer 687 of 764
Wed 06/12/13 03:01:08 DSP      LOG             0 Printing Layer 688 of 764
Wed 06/12/13 03:01:38 DSP      LOG             0 Printing Layer 689 of 764
Wed 06/12/13 03:02:08 DSP      LOG             0 Printing Layer 690 of 764
Wed 06/12/13 03:02:38 DSP      LOG             0 Printing Layer 691 of 764
Wed 06/12/13 03:03:08 DSP      LOG             0 Printing Layer 692 of 764
Wed 06/12/13 03:03:38 DSP      LOG             0 Printing Layer 693 of 764
Wed 06/12/13 03:04:08 DSP      LOG             0 Printing Layer 694 of 764
Wed 06/12/13 03:04:38 DSP      LOG             0 Printing Layer 695 of 764
Wed 06/12/13 03:05:08 DSP      LOG             0 Printing Layer 696 of 764
Wed 06/12/13 03:05:38 DSP      LOG             0 Printing Layer 697 of 764
Wed 06/12/13 03:06:08 DSP      LOG             0 Printing Layer 698 of 764
Wed 06/12/13 03:06:38 DSP      LOG             0 Printing Layer 699 of 764
Wed 06/12/13 03:07:08 DSP      LOG             0 Printing Layer 700 of 764
Wed 06/12/13 03:07:40 DSP      LOG             0 Printing Layer 701 of 764
Wed 06/12/13 03:08:10 DSP      LOG             0 Printing Layer 702 of 764
Wed 06/12/13 03:08:40 DSP      LOG             0 Printing Layer 703 of 764
Wed 06/12/13 03:09:10 DSP      LOG             0 Printing Layer 704 of 764
Wed 06/12/13 03:09:40 DSP      LOG             0 Printing Layer 705 of 764
Wed 06/12/13 03:10:10 DSP      LOG             0 Printing Layer 706 of 764
Wed 06/12/13 03:10:40 DSP      LOG             0 Printing Layer 707 of 764
Wed 06/12/13 03:11:10 DSP      LOG             0 Printing Layer 708 of 764
Wed 06/12/13 03:11:40 DSP      LOG             0 Printing Layer 709 of 764
Wed 06/12/13 03:12:10 DSP      LOG             0 Printing Layer 710 of 764
Wed 06/12/13 03:12:40 DSP      LOG             0 Printing Layer 711 of 764
Wed 06/12/13 03:13:10 DSP      LOG             0 Printing Layer 712 of 764
Wed 06/12/13 03:13:40 DSP      LOG             0 Printing Layer 713 of 764
Wed 06/12/13 03:14:10 DSP      LOG             0 Printing Layer 714 of 764
Wed 06/12/13 03:14:10 DEBUG    NOTICE         0 Bag Heater Off because nearing end of build
Wed 06/12/13 03:14:40 DSP      LOG             0 Printing Layer 715 of 764
Wed 06/12/13 03:15:10 DSP      LOG             0 Printing Layer 716 of 764
Wed 06/12/13 03:15:40 DSP      LOG             0 Printing Layer 717 of 764
Wed 06/12/13 03:16:10 DSP      LOG             0 Printing Layer 718 of 764
Wed 06/12/13 03:16:40 DSP      LOG             0 Printing Layer 719 of 764
Wed 06/12/13 03:17:10 DSP      LOG             0 Printing Layer 720 of 764
Wed 06/12/13 03:17:40 DSP      LOG             0 Printing Layer 721 of 764
Wed 06/12/13 03:18:09 DSP      LOG             0 Printing Layer 722 of 764
Wed 06/12/13 03:18:42 DSP      LOG             0 Printing Layer 723 of 764
Wed 06/12/13 03:19:12 DSP      LOG             0 Printing Layer 724 of 764
Wed 06/12/13 03:19:41 DSP      LOG             0 Printing Layer 725 of 764
Wed 06/12/13 03:20:11 DSP      LOG             0 Printing Layer 726 of 764
Wed 06/12/13 03:20:41 DSP      LOG             0 Printing Layer 727 of 764
Wed 06/12/13 03:21:11 DSP      LOG             0 Printing Layer 728 of 764
Wed 06/12/13 03:21:12 PREP     CTL_END_DSP_TRANSFER    0
Wed 06/12/13 03:21:41 DSP      LOG             0 Printing Layer 729 of 764
Wed 06/12/13 03:22:11 DSP      LOG             0 Printing Layer 730 of 764
Wed 06/12/13 03:22:41 DSP      LOG             0 Printing Layer 731 of 764
Wed 06/12/13 03:23:11 DSP      LOG             0 Printing Layer 732 of 764
Wed 06/12/13 03:23:41 DSP      LOG             0 Printing Layer 733 of 764
Wed 06/12/13 03:24:12 DSP      LOG             0 Printing Layer 734 of 764
Wed 06/12/13 03:24:44 DSP      LOG             0 Printing Layer 735 of 764
Wed 06/12/13 03:25:15 DSP      LOG             0 Printing Layer 736 of 764
Wed 06/12/13 03:25:47 DSP      LOG             0 Printing Layer 737 of 764
Wed 06/12/13 03:26:18 DSP      LOG             0 Printing Layer 738 of 764
Wed 06/12/13 03:26:49 DSP      LOG             0 Printing Layer 739 of 764
Wed 06/12/13 03:27:21 DSP      LOG             0 Printing Layer 740 of 764
Wed 06/12/13 03:27:53 DSP      LOG             0 Printing Layer 741 of 764
Wed 06/12/13 03:28:25 DSP      LOG             0 Printing Layer 742 of 764
Wed 06/12/13 03:28:57 DSP      LOG             0 Printing Layer 743 of 764
Wed 06/12/13 03:29:32 DSP      LOG             0 Printing Layer 744 of 764
Wed 06/12/13 03:30:04 DSP      LOG             0 Printing Layer 745 of 764
Wed 06/12/13 03:30:36 DSP      LOG             0 Printing Layer 746 of 764
Wed 06/12/13 03:30:36 PREP     COMPLETE          0
Wed 06/12/13 03:30:38 PREP     IDLE              0
Wed 06/12/13 03:31:08 DSP      LOG             0 Printing Layer 747 of 764
Wed 06/12/13 03:31:40 DSP      LOG             0 Printing Layer 748 of 764
Wed 06/12/13 03:32:13 DSP      LOG             0 Printing Layer 749 of 764
Wed 06/12/13 03:32:45 DSP      LOG             0 Printing Layer 750 of 764
Wed 06/12/13 03:33:17 DSP      LOG             0 Printing Layer 751 of 764
Wed 06/12/13 03:33:49 DSP      LOG             0 Printing Layer 752 of 764
Wed 06/12/13 03:34:21 DSP      LOG             0 Printing Layer 753 of 764
Wed 06/12/13 03:34:53 DSP      LOG             0 Printing Layer 754 of 764
Wed 06/12/13 03:35:26 DSP      LOG             0 Printing Layer 755 of 764
Wed 06/12/13 03:35:58 DSP      LOG             0 Printing Layer 756 of 764
Wed 06/12/13 03:36:30 DSP      LOG             0 Printing Layer 757 of 764
Wed 06/12/13 03:37:02 DSP      LOG             0 Printing Layer 758 of 764
Wed 06/12/13 03:37:35 DSP      LOG             0 Printing Layer 759 of 764
Wed 06/12/13 03:38:07 DSP      LOG             0 Printing Layer 760 of 764
Wed 06/12/13 03:38:39 DSP      LOG             0 Printing Layer 761 of 764
Wed 06/12/13 03:39:11 DSP      LOG             0 Printing Layer 762 of 764
Wed 06/12/13 03:39:43 DSP      LOG             0 Printing Layer 763 of 764
Wed 06/12/13 03:40:13 DSP      LOG             0 Printing Layer 764 of 764
Wed 06/12/13 03:40:42 DSP      LOG             0 Printing Layer 765 of 764
Wed 06/12/13 03:41:14 DSP      LOG             0 Finishing Job
Wed 06/12/13 03:41:16 DSP      LOG             0 Waiting For Secondary Thread
Wed 06/12/13 03:41:16 DSP      LOG             0 Build Done
Wed 06/12/13 03:41:16 DSP      LOG             0 Total Support Pump Ratio = 49.5
Wed 06/12/13 03:41:16 DSP      LOG             0 Total Part Pump Ratio = 33.7
Wed 06/12/13 03:41:16 BUILD    POST_CURE       0 Z Pos: -1.2534; ZL Encoder:  0.0000; ZR Encoder:  0.0000
Wed 06/12/13 03:41:17 DSP      LOG             0 Servo Enabled by PC
Wed 06/12/13 03:41:17 DSP      LOG             0 Beginning Post Cure
Wed 06/12/13 03:41:17 DSP      LOG             0 Lamp On       5.74
Wed 06/12/13 03:41:17 DSP      LOG             0 Lamp Off     11.14
Wed 06/12/13 03:41:17 DSP      LOG             0 Lamp Inches   5.41
Wed 06/12/13 03:41:17 DSP      LOG             0 Curing Layer 1 of 10
Wed 06/12/13 03:41:48 DSP      LOG             0 Curing Layer 2 of 10
Wed 06/12/13 03:42:17 DSP      LOG             0 Curing Layer 3 of 10
Wed 06/12/13 03:42:46 DSP      LOG             0 Curing Layer 4 of 10
Wed 06/12/13 03:43:15 DSP      LOG             0 Curing Layer 5 of 10
Wed 06/12/13 03:43:44 DSP      LOG             0 Curing Layer 6 of 10
Wed 06/12/13 03:44:13 DSP      LOG             0 Curing Layer 7 of 10
Wed 06/12/13 03:44:41 DSP      LOG             0 Curing Layer 8 of 10
Wed 06/12/13 03:45:10 DSP      LOG             0 Curing Layer 9 of 10
Wed 06/12/13 03:45:40 DSP      LOG             0 Curing Layer 10 of 10
Wed 06/12/13 03:46:08 DSP      LOG             0 Post Cure Complete
Wed 06/12/13 03:46:11 BUILD    DONE          100
Wed 06/12/13 03:46:12 BUILD    WAIT_RAISE_PLATFORM    0
Wed 06/12/13 03:46:12 DEBUG    TEMP_STATE_CHANGE    7 Control Build; Delay: 10
Wed 06/12/13 03:46:12 DSP      LOCAL_LOG       0 Realtime GO_TO_BUILD
Wed 06/12/13 03:46:12 DSP      LOCAL_LOG       0 Realtime READY_TO_BUILD
Wed 06/12/13 03:46:12 DSP      LOG             0 Raise Z
Wed 06/12/13 03:47:28 DSP      LOG             0 Z Top Limit Detected
Wed 06/12/13 03:47:28 BUILD    REMOVE_PLATFORM    0
Wed 06/12/13 03:47:29 DSP      LOG             0 Servo Disabled by PC
Wed 06/12/13 03:47:29 DEBUG    NOTICE         0 DONE: msnider@cv93gq1_engdsn-0011
Wed 06/12/13 03:47:29 DEBUG    NOTICE         0 Elapsed Time = 06:29
Wed 06/12/13 03:47:29 DEBUG    PARAM_CHANGE    0 LoadBuildStyle: STANDARD FRACTAL
Wed 06/12/13 05:46:13 DEBUG    TEMP_STATE_CHANGE    2 Control Standby
Wed 06/12/13 05:46:13 DSP      LOCAL_LOG       0 Realtime GO_TO_STANDBY
Wed 06/12/13 06:07:40 DEBUG    TEMP_STATE_CHANGE    2 Control Standby
Wed 06/12/13 06:07:40 DSP      LOCAL_LOG       0 Realtime STANDBY
Wed 06/12/13 11:19:09 BUILD    WAIT_READY      0
Wed 06/12/13 11:19:09 DEBUG    TEMP_STATE_CHANGE    4 Adapter Build
Wed 06/12/13 11:19:09 DSP      LOCAL_LOG       0 Realtime GO_TO_BUILD
Wed 06/12/13 11:19:09 DSP      LOCAL_LOG       0 Machine Off Time Sets Delay
Wed 06/12/13 11:19:09 DSP      LOCAL_LOG       0 Jetstack Delay = 10 Minutes
Wed 06/12/13 11:30:29 DEBUG    TEMP_STATE_CHANGE    5 Reservoir Build
Wed 06/12/13 11:33:08 DEBUG    TEMP_STATE_CHANGE    6 Jetstack Delay; Delay: 10
Wed 06/12/13 11:43:09 DEBUG    TEMP_STATE_CHANGE    7 Control Build; Delay: 10
Wed 06/12/13 11:43:35 DEBUG    TEMP_STATE_CHANGE    7 Control Build; Delay: 10
Wed 06/12/13 11:43:35 DSP      LOCAL_LOG       0 Realtime READY_TO_BUILD
Wed 06/12/13 11:52:07 SECURITY GET_SECURITY_INDEX     0 Index = 0
Wed 06/12/13 11:55:23 DEBUG    BTN_PRESSED    1 Online Pressed
Wed 06/12/13 11:55:23 BUILD    PRE_JOB_CHECKS    0
Wed 06/12/13 11:55:26 DEBUG    BTN_PRESSED   11 Yes Pressed
Wed 06/12/13 11:55:28 DEBUG    NOTICE         0 Send Parameters To DSP
Wed 06/12/13 11:55:28 DEBUG    TEMP_STATE_CHANGE    7 Control Build; Delay: 10
Wed 06/12/13 11:55:28 DSP      LOCAL_LOG       0 Realtime GO_TO_BUILD
Wed 06/12/13 11:55:28 DSP      LOCAL_LOG       0 Realtime READY_TO_BUILD
Wed 06/12/13 11:55:28 DSP      LOG             0 Servo Enabled by PC
Wed 06/12/13 11:55:28 BUILD    HOME_XY         0
Wed 06/12/13 11:55:29 DSP      LOG             0 Home X
Wed 06/12/13 11:55:30 DSP      LOG             0 Detected X Limit
Wed 06/12/13 11:55:30 DSP      LOG             0 Home Y
Wed 06/12/13 11:55:39 DSP      LOG             0 Detected Y Limit
Wed 06/12/13 11:55:39 BUILD    HOME_Z          0
Wed 06/12/13 11:55:40 DSP      LOG             0 Home Z
Wed 06/12/13 11:57:12 DSP      LOG             0 Z Right Limit Detected
Wed 06/12/13 11:57:12 DSP      LOG             0 Z Left Limit Detected
Wed 06/12/13 11:57:12 DSP      LOG             0 Delta Z set to -0.015000
Wed 06/12/13 11:57:12 BUILD    ONLINE          0
Wed 06/12/13 12:03:10 SECURITY GET_SECURITY_INDEX     0 Index = 0
Wed 06/12/13 12:03:55 SECURITY GET_SECURITY_INDEX     0 Index = 0
Wed 06/12/13 12:27:30 TCP      STORE_FILE      0  File:C:\ProJet\Bin\..\work\21338.ctl
Wed 06/12/13 12:27:31 TCP      SEND_JOB        0 192.168.10.56: msnider@cv93gq1_engdsn-0013
Wed 06/12/13 12:27:31 PREP     CTL_COMBINE_JOBS     0
Wed 06/12/13 12:27:31 DSP      LOG             0 DSP Comm Reset by PC
Wed 06/12/13 12:27:31 PREP     OPEN_FILES        0 Build Style: Standard
Wed 06/12/13 12:27:31 DEBUG    PARAM_CHANGE    0 LoadBuildStyle: STANDARD FRACTAL
Wed 06/12/13 12:27:32 PREP     CTL_INITIALIZE    3 Input File: C:\ProJet\Bin\..\work\21338.ctl, Support Type: FRACTAL, Minimum Supports: 0.216000, Draft Angle: 0
Wed 06/12/13 12:27:32 BUILD    PRE_BUILD       0
Wed 06/12/13 12:27:32 PREP     FRACTAL_DONE         0 Extents: X 0.746031 2.440881  Y 0.586920 3.994486  Z -0.000000 1.295290
Wed 06/12/13 12:27:36 BUILD    BLD_HEAD_CLEANING    0
Wed 06/12/13 12:27:36 HMS      WIPE_INITIATE    0 Materials Present - Head Cleaning Initiated
Wed 06/12/13 12:27:36 HMS      WIPE_MOVE_Z_TO_PICKUP    0 Beginning Printhead Maintenance
Wed 06/12/13 12:27:40 PREP     CTL_FINISH_SUPPORTS    0
Wed 06/12/13 12:27:40 PREP     CTL_GET_INITIAL_TOKENS    0 Filtering Zones; m_iZonePoolIndex = 4219
Wed 06/12/13 12:28:23 HMS      WIPE_CYCLE_START_STATE    0
Wed 06/12/13 12:28:37 HMS      WIPE_WAIT_PURGE    0
Wed 06/12/13 12:28:38 DSP      LOCAL_LOG       0 Start Printhead Purge
Wed 06/12/13 12:28:39 DSP      LOCAL_LOG       0 Support Pump Pos=0.902; Vacuum=0.003; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=63 sec; MPixels/Sec=0.000000
Wed 06/12/13 12:28:42 DSP      LOCAL_LOG       0 Support Pump Pos=0.927; Vacuum=0.003; Cnt=2
Wed 06/12/13 12:28:45 DSP      LOCAL_LOG       0 Support Pump Pos=0.952; Vacuum=0.003; Cnt=3
Wed 06/12/13 12:28:47 DSP      LOCAL_LOG       0 Part Pump Pos=1.277; Vacuum=0.003; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=71 sec; MPixels/Sec=0.000000
Wed 06/12/13 12:28:49 DSP      LOCAL_LOG       0 Support Pump Pos=0.977; Vacuum=0.003; Cnt=4
Wed 06/12/13 12:28:52 DSP      LOCAL_LOG       0 Part Pump Pos=1.302; Vacuum=0.003; Cnt=2
Wed 06/12/13 12:28:54 DSP      LOCAL_LOG       0 Support Pump Pos=1.002; Vacuum=0.003; Cnt=5
Wed 06/12/13 12:28:54 HMS      WIPE_WAIT_DRIP_STOP    0
Wed 06/12/13 12:28:55 DSP      LOCAL_LOG       0 End Printhead Purge
Wed 06/12/13 12:28:56 DSP      LOCAL_LOG       0 Part Pump Pos=1.327; Vacuum=0.003; Cnt=3
Wed 06/12/13 12:28:59 DSP      LOCAL_LOG       0 Support Pump Pos=1.027; Vacuum=0.003; Cnt=6
Wed 06/12/13 12:29:00 HMS      WIPE_START_STATE    0 Wipe Start: 1/7
Wed 06/12/13 12:29:01 DSP      LOCAL_LOG       0 Part Pump Pos=1.352; Vacuum=0.003; Cnt=4
Wed 06/12/13 12:29:03 DSP      LOCAL_LOG       0 Support Pump Pos=1.052; Vacuum=0.003; Cnt=7
Wed 06/12/13 12:29:06 DSP      LOCAL_LOG       0 Part Pump Pos=1.377; Vacuum=0.003; Cnt=5
Wed 06/12/13 12:29:08 DSP      LOCAL_LOG       0 Part Pump Pos=1.402; Vacuum=0.003; Cnt=6
Wed 06/12/13 12:29:11 DSP      LOCAL_LOG       0 Part Pump Pos=1.427; Vacuum=0.123; Cnt=7
Wed 06/12/13 12:29:14 DSP      LOCAL_LOG       0 Part Pump Pos=1.452; Vacuum=0.316; Cnt=8
Wed 06/12/13 12:29:16 DSP      LOCAL_LOG       0 Part Pump Pos=1.477; Vacuum=0.266; Cnt=9
Wed 06/12/13 12:30:29 HMS      WIPE_START_STATE    0 Wipe Start: 2/7
Wed 06/12/13 12:31:13 HMS      WIPE_START_STATE    0 Wipe Start: 3/7
Wed 06/12/13 12:31:56 HMS      WIPE_START_STATE    0 Wipe Start: 4/7
Wed 06/12/13 12:32:40 HMS      WIPE_START_STATE    0 Wipe Start: 5/7
Wed 06/12/13 12:33:24 HMS      WIPE_START_STATE    0 Wipe Start: 6/7
Wed 06/12/13 12:34:07 HMS      WIPE_START_STATE    0 Wipe Start: 7/7
Wed 06/12/13 12:34:51 HMS      WIPE_WAIT_GROUP_FIRE    0 Wipe Fire
Wed 06/12/13 12:34:51 DSP      LOG             0 Sending Normalization
Wed 06/12/13 12:35:03 DSP      LOG             0 Test Fire 90000 times at 24.00 kHz
Wed 06/12/13 12:35:03 DSP      LOG             0 Test Reg = D181 2181
Wed 06/12/13 12:35:13 HMS      WIPE_X_AT_DUMP_STATE    0 Wipe At Dump
Wed 06/12/13 12:36:25 HMS      WIPE_WAIT_DRIP_STOP_2    0
Wed 06/12/13 12:36:41 HMS      WIPE_WAIT_Z_PICKUP_2    0
Wed 06/12/13 12:37:07 HMS      WIPE_CYCLE_START_STATE    0
Wed 06/12/13 12:37:19 HMS      WIPE_WAIT_PURGE    0
Wed 06/12/13 12:37:19 DSP      LOCAL_LOG       0 Start Printhead Purge
Wed 06/12/13 12:37:22 DSP      LOCAL_LOG       0 Support Pump Pos=1.077; Vacuum=0.003; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=522 sec; MPixels/Sec=0.000000
Wed 06/12/13 12:37:24 DSP      LOCAL_LOG       0 Part Pump Pos=1.502; Vacuum=0.003; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=517 sec; MPixels/Sec=0.000000
Wed 06/12/13 12:37:26 DSP      LOCAL_LOG       0 Support Pump Pos=1.102; Vacuum=0.003; Cnt=2
Wed 06/12/13 12:37:29 DSP      LOCAL_LOG       0 Part Pump Pos=1.527; Vacuum=0.003; Cnt=2
Wed 06/12/13 12:37:31 DSP      LOCAL_LOG       0 Support Pump Pos=1.127; Vacuum=0.003; Cnt=3
Wed 06/12/13 12:37:33 DSP      LOCAL_LOG       0 Part Pump Pos=1.552; Vacuum=0.003; Cnt=3
Wed 06/12/13 12:37:36 HMS      WIPE_WAIT_DRIP_STOP    0
Wed 06/12/13 12:37:36 DSP      LOCAL_LOG       0 Support Pump Pos=1.152; Vacuum=0.003; Cnt=4
Wed 06/12/13 12:37:36 DSP      LOCAL_LOG       0 End Printhead Purge
Wed 06/12/13 12:37:38 DSP      LOCAL_LOG       0 Part Pump Pos=1.577; Vacuum=0.003; Cnt=4
Wed 06/12/13 12:37:40 DSP      LOCAL_LOG       0 Support Pump Pos=1.177; Vacuum=0.003; Cnt=5
Wed 06/12/13 12:37:41 HMS      WIPE_START_STATE    0 Wipe Start: 1/7
Wed 06/12/13 12:37:43 DSP      LOCAL_LOG       0 Part Pump Pos=1.602; Vacuum=0.003; Cnt=5
Wed 06/12/13 12:37:45 DSP      LOCAL_LOG       0 Support Pump Pos=1.202; Vacuum=0.003; Cnt=6
Wed 06/12/13 12:37:48 DSP      LOCAL_LOG       0 Part Pump Pos=1.627; Vacuum=0.176; Cnt=6
Wed 06/12/13 12:37:50 DSP      LOCAL_LOG       0 Part Pump Pos=1.652; Vacuum=0.795; Cnt=7
Wed 06/12/13 12:37:53 DSP      LOCAL_LOG       0 Part Pump Pos=1.677; Vacuum=1.509; Cnt=8
Wed 06/12/13 12:37:56 DSP      LOCAL_LOG       0 Part Pump Pos=1.702; Vacuum=2.173; Cnt=9
Wed 06/12/13 12:37:58 DSP      LOCAL_LOG       0 Part Pump Pos=1.727; Vacuum=2.470; Cnt=10
Wed 06/12/13 12:39:10 HMS      WIPE_START_STATE    0 Wipe Start: 2/7
Wed 06/12/13 12:39:53 HMS      WIPE_START_STATE    0 Wipe Start: 3/7
Wed 06/12/13 12:40:37 HMS      WIPE_START_STATE    0 Wipe Start: 4/7
Wed 06/12/13 12:41:21 HMS      WIPE_START_STATE    0 Wipe Start: 5/7
Wed 06/12/13 12:42:05 HMS      WIPE_START_STATE    0 Wipe Start: 6/7
Wed 06/12/13 12:42:48 HMS      WIPE_START_STATE    0 Wipe Start: 7/7
Wed 06/12/13 12:43:31 HMS      WIPE_WAIT_GROUP_FIRE    0 Wipe Fire
Wed 06/12/13 12:43:32 DSP      LOG             0 Sending Normalization
Wed 06/12/13 12:43:44 DSP      LOG             0 Test Fire 90000 times at 24.00 kHz
Wed 06/12/13 12:43:44 DSP      LOG             0 Test Reg = D181 2181
Wed 06/12/13 12:43:53 HMS      WIPE_X_AT_DUMP_STATE    0 Wipe At Dump
Wed 06/12/13 12:45:06 HMS      WIPE_WAIT_DRIP_STOP_2    0
Wed 06/12/13 12:45:21 HMS      WIPE_X_PARKED    0
Wed 06/12/13 12:45:25 HMS      WIPE_SOLENOID_DISENGAGE    0 Wipe Parked
Wed 06/12/13 12:45:39 HMS      WIPE_WAIT_Z_BUILD_START    0
Wed 06/12/13 12:45:50 HMS      WIPE_INACTIVE    0 Printhead Maintenance Completed
Wed 06/12/13 12:45:51 DSP      LOCAL_LOG       0 Printhead Maintenance Completed
Wed 06/12/13 12:45:51 BUILD    BUILD_BEGIN     0
Wed 06/12/13 12:45:51 DEBUG    TEMP_STATE_CHANGE    7 Control Build; Delay: 10
Wed 06/12/13 12:45:51 DSP      LOCAL_LOG       0 Realtime BUILD_PART
Wed 06/12/13 12:45:54 DSP      LOG             0 Manual Cure UV LEDS  2.0 Seconds
Wed 06/12/13 12:45:56 DSP      LOG             0 Latched 1760 1475 2130 2089
Wed 06/12/13 12:45:56 DSP      LOG             0 Manual Cure UV LEDS  2.0 Seconds
Wed 06/12/13 12:45:58 DSP      LOG             0 Latched 1829 1509 2142 2010
Wed 06/12/13 12:45:59 DSP      LOG             0 Manual Cure UV LEDS  2.0 Seconds
Wed 06/12/13 12:46:01 DSP      LOG             0 Latched 1720 1444 2044 1903
Wed 06/12/13 12:46:01 DSP      LOG             0 Measure Uv Leds
Wed 06/12/13 12:46:01 DSP      LOG             0 Measured 1829 1509 2142 2010
Wed 06/12/13 12:46:02 DSP      LOG             0 Begin Build
Wed 06/12/13 12:46:03 BUILD    BUILD_FANS_OFF    0
Wed 06/12/13 12:46:05 DSP      LOG             0 Sending Normalization
Wed 06/12/13 12:46:05 DSP      LOG             0 Build Mode = 0
Wed 06/12/13 12:46:05 DSP      LOG             0 Build Extents
Wed 06/12/13 12:46:05 DSP      LOG             0 X -   0.000000    1.753920
Wed 06/12/13 12:46:05 DSP      LOG             0 Y -   0.000000    3.471300
Wed 06/12/13 12:46:05 DSP      LOG             0 Z -   0.000000    1.294830
Wed 06/12/13 12:46:05 DSP      LOG             0 Pixel Size -   0.003045    0.003045
Wed 06/12/13 12:46:05 DSP      LOG             0 Slice Layer Thickness -   0.001580
Wed 06/12/13 12:46:05 DSP      LOG             0 Printing Layer 1 of 819
Wed 06/12/13 12:46:06 BUILD    BUILD           0
Wed 06/12/13 12:46:27 DSP      LOG             0 Printing Layer 2 of 819
Wed 06/12/13 12:46:50 DSP      LOG             0 Printing Layer 3 of 819
Wed 06/12/13 12:47:10 DSP      LOG             0 Printing Layer 4 of 819
Wed 06/12/13 12:47:30 DSP      LOG             0 Printing Layer 5 of 819
Wed 06/12/13 12:47:50 DSP      LOG             0 Printing Layer 6 of 819
Wed 06/12/13 12:48:10 DSP      LOG             0 Printing Layer 7 of 819
Wed 06/12/13 12:48:30 DSP      LOG             0 Printing Layer 8 of 819
Wed 06/12/13 12:48:50 DSP      LOG             0 Printing Layer 9 of 819
Wed 06/12/13 12:49:11 DSP      LOG             0 Printing Layer 10 of 819
Wed 06/12/13 12:49:31 DSP      LOG             0 Printing Layer 11 of 819
Wed 06/12/13 12:49:51 DSP      LOG             0 Printing Layer 12 of 819
Wed 06/12/13 12:50:11 DSP      LOG             0 Printing Layer 13 of 819
Wed 06/12/13 12:50:31 DSP      LOG             0 Printing Layer 14 of 819
Wed 06/12/13 12:50:51 DSP      LOG             0 Printing Layer 15 of 819
Wed 06/12/13 12:51:11 DSP      LOG             0 Printing Layer 16 of 819
Wed 06/12/13 12:51:31 DSP      LOG             0 Printing Layer 17 of 819
Wed 06/12/13 12:51:51 DSP      LOG             0 Printing Layer 18 of 819
Wed 06/12/13 12:52:12 DSP      LOG             0 Printing Layer 19 of 819
Wed 06/12/13 12:52:32 DSP      LOG             0 Printing Layer 20 of 819
Wed 06/12/13 12:52:52 DSP      LOG             0 Printing Layer 21 of 819
Wed 06/12/13 12:53:12 DSP      LOG             0 Printing Layer 22 of 819
Wed 06/12/13 12:53:32 DSP      LOG             0 Printing Layer 23 of 819
Wed 06/12/13 12:53:54 DSP      LOG             0 Printing Layer 24 of 819
Wed 06/12/13 12:54:14 DSP      LOG             0 Printing Layer 25 of 819
Wed 06/12/13 12:54:34 DSP      LOG             0 Printing Layer 26 of 819
Wed 06/12/13 12:54:55 DSP      LOG             0 Printing Layer 27 of 819
Wed 06/12/13 12:55:15 DSP      LOG             0 Printing Layer 28 of 819
Wed 06/12/13 12:55:35 DSP      LOG             0 Printing Layer 29 of 819
Wed 06/12/13 12:55:55 DSP      LOG             0 Printing Layer 30 of 819
Wed 06/12/13 12:56:15 DSP      LOG             0 Printing Layer 31 of 819
Wed 06/12/13 12:56:35 DSP      LOG             0 Printing Layer 32 of 819
Wed 06/12/13 12:56:55 DSP      LOG             0 Printing Layer 33 of 819
Wed 06/12/13 12:57:16 DSP      LOG             0 Printing Layer 34 of 819
Wed 06/12/13 12:57:17 DSP      LOCAL_LOG       0 Support Pump Pos=1.227; Vacuum=4.578; MPixels=0.000000; 5Ave=0.000; 10Ave=0.000; 20Ave=0.000; Last Pump=1196 sec; MPixels/Sec=0.000000
Wed 06/12/13 12:57:36 DSP      LOG             0 Printing Layer 35 of 819

rh3000 · Jun 12, 2013

*** said:
cleaned contacts of what?

plugs for what?

Anyway, good to hear it seems to be fixed (for now, LOL)

Have you tried the Crystal VisiJet material?

No... we use whatever 3D Systems told us to use (SR200 and S100) and it's not cheap.

Cos

TECHARTISAN · Sep 12, 2013

Well since this seems to be the DIY repair shop thread.....
Our invisionhr is paralyzed. Xhome fatal error.
so I took it all apart....cleaned the strip....reassembled...
still getting the same error....
went into the remote diag...
manually moving X shows change of encoder positon.
Attempted to home Y..... Yhome fatal error
tried to do a short Z move.....DSP error.

Anyone have any ideas?

DMC · Sep 13, 2013

Would be glad to take a peek via teamviewer today.
804-285-0777 "Scott"

ProJetter · Sep 13, 2013

TECHARTISAN said:
Well since this seems to be the DIY repair shop thread.....
Our invisionhr is paralyzed. Xhome fatal error.
so I took it all apart....cleaned the strip....reassembled...
still getting the same error....
went into the remote diag...
manually moving X shows change of encoder positon.
Attempted to home Y..... Yhome fatal error
tried to do a short Z move.....DSP error.

Anyone have any ideas?

Sounds not as well! DSP params are controlled by main control board!
Have u still tried to stop the invision-service & perform a whole reboot of windows (ony printer-side) by remote desktop connection (ALT+F4 enables the reboot)?
I guess there's "only" something not recognized during startup!

Another solution can be a "forced" error-msg inside your machine.ini file!
Hope Scott can help u to solve the problem!

DMC · Sep 13, 2013

Once you have a main axis error, I think you cannot move any other axis untill reboot.

Attempting to move the Y or Z will only show more error, and the motors are turned off.

Right Mr Jet?

ProJetter · Sep 13, 2013

*** said:
Right Mr Jet?

Correct Mr. D!
Dunno if maybe only a forced error instead of a reboot will also work

As always, too many secrets on those machines / rmtdiag's

DP3000 error

rh3000

New Member

DMC

Banned

DMC

Banned

Eugene_M

New Member

DMC

Banned

Eugene_M

New Member

rh3000

New Member

DMC

Banned

rh3000

New Member

DMC

Banned

rh3000

New Member

DMC

Banned

DMC

Banned

rh3000

New Member

rh3000

New Member

TECHARTISAN

Active Member

DMC

Banned

ProJetter

Member

DMC

Banned

ProJetter

Member

Similar threads