Ceramil Therm

D

Danutule

Member
Full Member
Messages
19
Reaction score
2
Does anyone have an instruction manual for Ceramill Therm zirconium sintering oven (from Amann Girrbach) ? I have the older version, with one display. I realy dont know how to modify the program (s). Thank you.
 
Affinity

Affinity

Well-Known Member
Donator
Full Member
Messages
6,917
Reaction score
1,062
You can download it from their website. The controls on that oven are utterly ridiculous and make no sense. You must have the book or its impossible. Also, i started a ceramill thread so theres some more info there.
 
Affinity

Affinity

Well-Known Member
Donator
Full Member
Messages
6,917
Reaction score
1,062
Also, never buy elements for that thing from amann.. they are marked up 4-5x. I can get you a part # from the mfg.
 
D

Danutule

Member
Full Member
Messages
19
Reaction score
2
On their website is the instruction manual only for the newest version of the oven (with two displays, green and red) i have the version with only one display (green one). Do only some commands apply to my oven. Do you have the same oven ?
 
Affinity

Affinity

Well-Known Member
Donator
Full Member
Messages
6,917
Reaction score
1,062
No I have the therm 2. I know its out there.. Are you a motion user also?
 
Affinity

Affinity

Well-Known Member
Donator
Full Member
Messages
6,917
Reaction score
1,062
Call amann US they can email you the .pdf ... AND try and sell you a new one.
 
Sydceramist

Sydceramist

Active Member
Full Member
Messages
110
Reaction score
6
You cant change the program o n the 1st version, you would have to install a temperature controller (eurotherm).
 
D

Danutule

Member
Full Member
Messages
19
Reaction score
2
But on the back of the oven is written Max temp 1500C and the program goes up to only 1450, so theoretically it could go up to 1500... i can enter the settings but it asks for password, and any password i write and then pres any button, it exits the settings... what password should i put ?
 
prestige.dental

prestige.dental

Active Member
Full Member
Messages
270
Reaction score
15
can somebody please tell me how do post a case. I found a IZIR bridge fractured in my ivoclar programat S1 oven after over night sintering. I wanted to post pictures. I just can't figure out how to post the case.

thanks

Sam
 
Sydceramist

Sydceramist

Active Member
Full Member
Messages
110
Reaction score
6
I wish i knew, I think the program is set to 1450, mine says max temp 1530 so yes it can go not with the existing controller, if it is asking for a password then that is interesting!
 
D

Danutule

Member
Full Member
Messages
19
Reaction score
2
buttons are numerated from left to right 1 2 3 4

Instruction for changing the program parameters
These instructions start from the basic operator mode (OP.b) with
the controller in the Hold state.
a) Press and hold and simultaneously 1 2 for
more than 3 seconds, the display will flash between
OP.r and OP.b
b) Press 3 or 4 to choose OP.S
c) Press 1 to confirm the selected level. The word Pass will flash on the display for 10 seconds. During
this period the password should be selected.
d) Choose with 3 and 4 the value 19 (password)
e) Press 1 to confirm the password.
f) Press 1 to choose the parameter which has to be changed:
o SP 1 (temperature set point),
o SPrr (set point ramp rate)
o T (timer value)
o CEt (End Temperature of the program)
o SSt (Temperature threshold for which the soft start will end)
o SOP (Percentage output power for soft start)
g) Press 3 and 4 to change values:
o SP 1 = 1450°C (standard)
o SPrr = 8°C/min (standard)
o T = 2.0h (standard)
o CEt = 200°C (standard)
o SSt = 400°C (standard)
o SOP = 22 (standard)
h) Press 1 to confirm
i) Press 1 or wait for about 30s until Hold appears in the display.
j) Press 1 and 2 and hold and simultaneously for
more than 3 seconds again.
k) Choose with 3 and 4 the OP.b mode and confirm with 1
Note: OP.S mode will not time out and return to OP.b. This must be done
manually!
The maximum power of the furnace is limited to a end temperature of 1500°C.
After changing the parameters, the correct function of the furnace should be proofed by a short test.
 
Sydceramist

Sydceramist

Active Member
Full Member
Messages
110
Reaction score
6
Wow! great, have you tried a test run of this? Thanks!
 
Sydceramist

Sydceramist

Active Member
Full Member
Messages
110
Reaction score
6
Hi I tried it great! Thanks!
All I did was adjust the temperature left all the other settings as factory.
the reseller here was an idiot I asked them about this an was given a false answer.
 
D

Danutule

Member
Full Member
Messages
19
Reaction score
2
Sydceramist, from what country are you ?
 
N

Nicholas Allred

New Member
Messages
1
Reaction score
0
Hey, I just found this thread on google. I have the ceramill therm and am looking at cheaper options to replace my heating elements. Do you know if it is still possible to buy parts from manufacturer? Thanks so much in advance for any info you can give me on this.

Nick Allred


Hey guys, I have had the ceramill therm since 2014 and the heating elements just went out. I found your page googling information about it and saw this thread.
Also, never buy elements for that thing from amann.. they are marked up 4-5x. I can get you a part # from the mfg.
 
JMN

JMN

Christian Member
Full Member
Messages
12,205
Reaction score
1,884
Hey, I just found this thread on google. I have the ceramill therm and am looking at cheaper options to replace my heating elements. Do you know if it is still possible to buy parts from manufacturer? Thanks so much in advance for any info you can give me on this.

Nick Allred


Hey guys, I have had the ceramill therm since 2014 and the heating elements just went out. I found your page googling information about it and saw this thread.
Greetings Earthling! Welcome!

Can't help you there, but thought I'd say hi. Affinity is a regular and will be around.
 
Getoothachopper

Getoothachopper

Well-Known Member
Full Member
Messages
809
Reaction score
411
Here is some info for the Elements . I don't remember what I paid but it was a lot less (got two sets) . Downside was they came from Scotland and took six weeks to get to me . Hope this helps :)
DSC01587.JPG DSC01588.JPG DSC01589 (1).JPG
 

Similar threads

K
Replies
0
Views
637
korlab
K
R
Replies
4
Views
185
millennium
millennium
millennium
Replies
5
Views
877
millennium
millennium
GhostFake
Replies
14
Views
354
Car 54
Car 54
L
Replies
0
Views
2K
leandro silva h
L
Top Bottom