Search results

  1. REJ

    Exocam with Sum3D -Missing Tools Error

    I found that this happens as a result of Type select commands. If the script is modified so they are special commands it works. As it runs in hidden mode it seems to always choose just as a crown or the simplest version.
  2. REJ

    New Imes-Icore 350I

    We have not had problems doing it for a year which is all the data we can collect since it it is still relatively new. It is our machine of choice on all full arch screw retained and long span high angulation cases. I believe the only service we did was unrelated and was that the safety door...
  3. REJ

    New Imes-Icore 350I

    You are correct the way I envision it is that the 350i has its zero point essentially in the center of a sphere and could therefore reach pretty much any point in said sphere as long as the fixture is not in the way. it has virtually unlimited range of motion in that regard so very complex...
  4. REJ

    New Imes-Icore 350I

    It is currently recommended for 30 degrees in both A and B dynamically with a disc (pretty conservative) but in reality the A is rotary and the b can move from something like -30 to 120 meaning that the dynamics are more like a roeders or Mikron where it can do machining with the B at 9O with...
  5. REJ

    New Imes-Icore 350I

    We have been running the 350i for over a year now and it is the go to machine for our complex cases, we have it in our dry milling center now but have previously run lots of abutments and high angulation bars in the past for testing. Now it is our primary machine on full arch screw retained...
  6. REJ

    Cam for imes 250i

    I think that HD and Sum have very similar functionalities at the core. Both will give you what put into it and learn on the software. There is an imes v5 250i version which is quite affordable, but I do not have issues with hyper dent. Only issue with hyper dent is that they made what I...
  7. REJ

    New inLab MC 5-Axis "Open" Mill

    Zero Zero is dead on with the description from a dynamics perspective there are advantages to 3+2 in certain application, for example mos implant bars and screw channels where an a and b axis can tilt then allow for more rapid and stabile machining in three axis mode at a tilt. For more dynamic...
  8. REJ

    Exocad training questions to ask of trainer.

    As someone that used to train a lot of folks on technology I would suggest that you do research to find out that the company is legit and that they can support your future goals with their knowledge and that you thing has a good report, it is good to include some idea of the type of business you...
  9. REJ

    T neutral and T0 or T clear

    It is usually what I went through the most of out all the porcelains since it is used on almost every case. In general I was taught to create dentine skeleton bake, use effects and add clear and then cover it with a thin enamel shell. This results in a more vital looking restorations with a...
  10. REJ

    milling machine

    I use the V5 with the 350i and think it is more capable to extend the limits of the 350i than the 4.6 and in my opinion it is better to learn the more advanced cam from the start instead of reaching a point where you want to cut more complex parts but spend time learning basics of a new cam.
  11. REJ

    Opacity with Cubex

    One common thing I've noticed is that the oven may have too many units causing opacity. Most ovens have room to fit more units than can reach the proper sintering conditions so a smaller unit like the p1 may be rated at 30 copings and will be based on small thimble copings rather than the full...
  12. REJ

    NT Trading Two connect

    We had issues with the same thing John on our first case like that and since usually go to the fixture level unless it was already impressed at abutment level and has a corresponding analog. Usually they are done as manual positioning screw retained so we can alter the parts as necessary. The...
  13. REJ

    How to mill this?

    You could replace the geometry with a radius compensation at the point where it is too tight, obviously custom and smaller tooling is going to make this easier as well.
  14. REJ

    WOW FINALLY!!

    The Price on the 850i is around 175k, plus around another 100k for the Robotic automation. 650i has a loth of the same features and will be less money but is not in production yet.
  15. REJ

    Super-Translucent Zirconias

    Here is a try-in was not cemented pending FDA cert, sorry no shade tab but it had to have been used at some point.
  16. REJ

    VHF Modifications

    The suction is a big weak point on that machine, It also is insufficient to keep the dust from going into the electrical components and drive system. If it is not covered I would probably modify it like Sevan recommends otherwise the dust goes into the right side of the machine through the...
  17. REJ

    CubeX2

    The CubeX2 is on the normal firing parameters of Bio Zx2 and is compatible with the monolith zero staining, only difference as Jason mentioned is that the shading is done one shade darker than on BioZ. So A1 cubex uses the a2 liquid. We have introduced + shades for a4+, etc. to use on the...
  18. REJ

    3 shape stand alone seat

    I got a stand alone back a few years. I believe it ran around 6,500 for the crown and bridge, I think the additional modules are regular price as with the scanner. That was for just the license, no pc. It would probably be similar for you since the deal was that I did all the hardware and...
  19. REJ

    Large Lab machines vs Milling center machines

    There is not really a definitive line as to what is industrial vs dental, and what they can or cannot excel in producing. For example Datron, and Imes make the same basic machines for dental and industry. In general the thousands of parts at a time are done on a swiss machine like above which...
  20. REJ

    New Imes-Icore 350I

    The way the new lineup will compare from Imes is that the 350i will be the same category as the 450i but with some enhancements in technology such as the integrated loader and zero point clamping system. It has an on board control computer and also 20x tool changer. The spindle is similar to...
Top Bottom