Search results

  1. elpiojoxp

    Sintering Zirconia Q&A

    Hello, I just use a brush and pressured air, also I use a microbrush to clean the inside of the crown and pressured air. I neved had any issue with ¨trace elements created by the dryer¨. I throw some air into my hand and observe that only air comes out before throwing the air into the zirconium.
  2. elpiojoxp

    Sintering Zirconia Q&A

    Hello dude, I just make this sintering curve: Ramp 1: 8° C per minute High Temp 1: 900° C Hold: 0 hr 30 min Ramp 2: 3° C per minute High Temp 2: 1450° C Hold: 2 hr 0 min Cooling Reg: Cool to 400° C in 2 hours and then let cool to room temperature naturally. In my experience, all zirconia...
  3. elpiojoxp

    Dental Direkt ProShade C Liquid

    Hello, any news about the new liquids? Thank you!
  4. elpiojoxp

    Dental Direkt ProShade C Liquid

    So, did you try the new Dental Direkt ProShade C Liquid? how it is? Thank you for share your experience Best regards
  5. elpiojoxp

    Dental Direkt ProShade C Liquid

    Hello everybody, I want to ask you all if anybody had the chance to test this new product: Dental Direkt ProShade C Liquid, they proclaim its a much better green state pre-sintering liquid, with this liquid and the Dental Direkt ArtElements - Effect colors you can just sinter and glaze your full...
  6. elpiojoxp

    CubeX2

    wow, I allways read in this forum DD liquids are waterbased and not acid...
  7. elpiojoxp

    CubeX2

    @user name, you are talking about DD BioZX2 MONOLITH ZERO pre sintering liquids right?
  8. elpiojoxp

    CubeX2

    As long as I know DD BioZX2 MONOLITH ZERO they are waterbased.
  9. elpiojoxp

    CubeX2

    Can you please share what you change in your process and the "few tweaks" in the sahding guide? Thank you very much! Regards
  10. elpiojoxp

    Sintering Zirconia Q&A

    Hello everybody, This is me again, I will post two photos, both crows should be A3,5, They are CubeX2, The theet 1.1 was sintered at 1450 C. The theet 2.1 was sintered at 1500 C. Both crowns looks too grey and with a pearly appearance, such as the colour having inside a marine oyster. The...
  11. elpiojoxp

    Sintering Zirconia Q&A

    Ok, thank you very much for your help, I will sinter and hold to 1500°C and I will let you know what happens. Regards
  12. elpiojoxp

    Opacity with Cubex

    Can you PLEASE see the pictures in the following link and tell me if that is what is expected for a well sintered cubex2? Or its overfired, or underfired? Thank you very much! http://dentallabnetwork.com/forums/threads/sintering-zirconia-q-a.20913/page-3
  13. elpiojoxp

    Opacity with Cubex

    Can you PLEASE see the pictures in the following link and tell me if that is what is what expected of a well sintered cubex2? Thank you very much! http://dentallabnetwork.com/forums/threads/sintering-zirconia-q-a.20913/page-3
  14. elpiojoxp

    Sintering Zirconia Q&A

    Hello, what do you think about my case? its a CubeX2 and it dont look good.... It should be colour A3,5. It dont have stain and glaze, only pre sintering Dental Direkt liquids and sintered. Do you think its over fired or underfired? What I did wrong? I used this sintering cycle: Ramp 1: 8° C...
  15. elpiojoxp

    Share your experience and help to decide best workflow

    Hello Mr Brent Harvey, thank you very much for your information. Can you please send me a price list to my email of all your zirconia, PMMA and WAX pucks and the liquids, stains, glaze, etc? My email is [email protected] Thank you very much Best regards
  16. elpiojoxp

    Share your experience and help to decide best workflow

    Hello everybody, Im asking for some help to let me decide wich brand of zirconia and liquids I must buy. Which brand a product offer the most easy workflow and less hand work time? Basically Im looking for 3 tipes of zirconia: 1) Im looking for the most strength zirconia available for customized...
  17. elpiojoxp

    Shining 3D AutoScan-DS200 Dental Scanner

    It looks like you dont read the full post, im not trying to defend anything, I only want to know the truth about a product, an opinion its nothing more than that, an opinion, I respect it, but in this particular case it is 100% subjective, and also full of prejudice, only because it is Chinese...
  18. elpiojoxp

    Shining 3D AutoScan-DS200 Dental Scanner

    I agree with your reasoning in general, but what I'm trying to figure out how is actually this scanner, it has less than 15microns precision, which is very good, it's automatic, with great space for models, very fast, simple to use, has texture, color, it works with open system, what lacks? Its...
  19. elpiojoxp

    Shining 3D AutoScan-DS200 Dental Scanner

    Thank you for the info about 3MF and STL. So, your statements were conclusive, but they are only based on personal assumptions, we are free to express ourselves in this forum, but as I said initially, I'm in search of facts and not on unfounded assumptions. Cheaper does not mean lower quality...
  20. elpiojoxp

    Shining 3D AutoScan-DS200 Dental Scanner

    I understand your point, but what is your base to say that is garbage and in 12-16 months you must throw it away and buy a new one? Have you tried it personally? I am not for or against anyone or anything, I just want to see first-hand experience that have worked and those who have used this...
Top Bottom