• Welcome to Dental Lab Network
    1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

    Nexx Zr T Speed cycle?

    Discussion in 'SageMax' started by John C, Jun 28, 2017.

    1. John C

      John C Member Full Member

      Joined:
      Jun 2015
      Messages:
      131
      Likes Received:
      19
      Has anyone figured out a speed sintering cycle that works with the Nexx ZR T ...?
       
    2. John C

      John C Member Full Member

      Joined:
      Jun 2015
      Messages:
      131
      Likes Received:
      19
      No one has a suggestiin for this?
       
    3. Affinity
      Question

      Affinity Well-Known Member Full Member

      Joined:
      Oct 2009
      Messages:
      3,660
      Likes Received:
      697
      Location:
      7B
      ..why dont you call sagemax? Dontknow
       
    4. CatamountRob
      Dead

      CatamountRob Banned Member Full Member

      Joined:
      Feb 2009
      Messages:
      4,833
      Likes Received:
      1,220
      Location:
      Verde Mont
      He's asking in the Sagemax forum, that should count for something.
      Where are ya @Brent Harvey?
       
    5. Affinity
      Question

      Affinity Well-Known Member Full Member

      Joined:
      Oct 2009
      Messages:
      3,660
      Likes Received:
      697
      Location:
      7B
      aha, I see that now, but they dont really have a presence here since brent left..
       
      • Agree Agree x 2
    6. grantoz
      Amused

      grantoz Well-Known Member Full Member

      Joined:
      Oct 2010
      Messages:
      983
      Likes Received:
      268
      look at the sirona speed fire thread.see if you can resist being sironaded ,oh yeh its a word now.
       
    7. CreDes
      No Mood

      CreDes Active Member Donator Full Member

      Joined:
      Aug 2010
      Messages:
      247
      Likes Received:
      66
      Location:
      Knoxville, TN
      They have a speed program. I will try to post it tomorrow for you.
       
    8. biodentg
      Relaxed

      biodentg Active Member Full Member

      Joined:
      Sep 2009
      Messages:
      383
      Likes Received:
      40
      yes, @Brent Harvey was a great help, I don't think I was a good idea for Sagemx to let him go.
       
      • Like Like x 1
    9. CreDes
      No Mood

      CreDes Active Member Donator Full Member

      Joined:
      Aug 2010
      Messages:
      247
      Likes Received:
      66
      Location:
      Knoxville, TN
      IMG_1412.JPG
       
      • Like Like x 2
    10. Brent Harvey
      Thinking

      Brent Harvey Active Member Full Member

      Joined:
      Oct 2013
      Messages:
      342
      Likes Received:
      152
      Location:
      Federal Way, WA
      Hey John,

      Feel free to shoot my cell a call I will go over some good cycles with you. The speed cycle that CreDes posted is good but it is only a starter point. It may need to be adjusted based on the esthetics that you get after you first cycle. It is always great to go by firing cycles of the manufacturer but most of the time they will take tweaking based on the location you are, as elevation can play a huge role on your final esthetics.
       
    11. John C

      John C Member Full Member

      Joined:
      Jun 2015
      Messages:
      131
      Likes Received:
      19
      Thanks Brent. I did a couple units with the cycle listed above. 3.5 hour cycle. It worked well. I dont plan to quick sinter too often but it can be a life saver when needed.
       
      • Like Like x 1

    Share This Page