Search results

Why my crowns are tight now in insertion in the pt. mouth , i haven’t changed anything as far as I know,. cement spacer is the same ,shrink rate is dialed in as indicated on the puck , sintering is the same. any idea?

For the experts of the Dekema furnaces code. How do you translate this chart into the Dekema sintering code? I have the Dekema basic furnace. I need the long sintering program for this furnace. I am having difficulty with this; thanks

I operate on an old version of Exocad 2016, I get scants from Itero, primescan and has been smooth sailing . But today I got this note and my cad and Exocad viewer are not opening , any idea? I know it’s old Exocad,

I have a case done seven years ago, its a cement retained single implant that the screw became lose and came off. How to debond the titanium abutment from the the zirconia crown without damage? I know you could heat up in ceramic oven at low temp, what temp needed? Any feedback is...

How do you change the scaling numbers for zir puck after mistakingly adding the wrong numbers and getting inaccurate fitting crown? Thanks i know I could rename the puck but I would like to keep the milled space on puck, I can’t find any option to edit scaling

I am interested to know from you out there the quality of scans sent from Primescan to Exocad comparing?, a dentist recently gave me a free connection but not installed on my system yet!

A piece of the firing chamber of the sinter furnace fell off, I wonder if there is any high heat cement that’s good and withstand the hi heat in there to cement that piece back? I used thin investment in the past , it holds for a couple of months and I had to do it over, I know replacing the...

I need your feed back on Origin Beyond + zir, shade, milling , and zirconium strength in green stage . Thanks

I think I need to replace the heating elements on this sintering furnace it says’ heating system error‘, any idea on a good support company for Dekema parts? Luckily the error at the beginning of the cycle of 22 zir units!, thank you in advance

I am interested to know your techniques on fabricating a crown to fit a clasp partial, some docs implement blue mouse registrations of clasps in relation to prepped tooth for that, but it’s not always accurate , I do the replication of clasps by placing the blue mouse registration over the...

your advice friends, which is better?, s to stick with branded Exocad or full blown Exocad? And why? As usual I thank you

Six lower incisors veneers pressed with GC initial LISI shade MT-Bo, Pt, requested incisal edge to be even and flat.

I have a 5 titanium custom abutments implants designed on Argen older scan bodies /Exocad, and now Argen has new scan bodies and don’t accept my stl files, they insist that I upgrade my Exocad software in order to install the new library on my system, ( my Exocad build is not compatible)...

I have been taking copies or pics of finished crowns in CAD design in order to identify zirconia crowns to stain, sinter and finish etc. since I have no physical model, so what is your method of identifying crowns without physical model? where they are many units involved so I don’t end in a...

Your suggestions will be appropriated on a new Exocad reseller with good tech support, my reseller dose not support Exocad any more, they suggested somebody which he seems very knowledgeable, but I am Interested to see your feedback. Thanks

It seems that many are quite this morning, so how’s your temperature 🤒? Do you take it often?!🤒🤒😊

What’s the fastest and easiest method in recalling cases to be re nested in Exocad/ Hyperdent?, I know i can go through load scan design...etc..thanks

How do you design an access whole on the occlusion of a crown(Zirconia) in Exocad when using attachment option , thanks

Good morning, What is your method in scanning a single unit in order to safe time and steps?, it’s taking me too much time to scan with all those steps!. I have Exocad/ Preciso/ Stinbechlor scanner. Thanks

Hello friends, i have a dentist who is buying a cerec oral scanner and wants to know if I could receive his scans (stl). I am not very well versed on this issue, My system is exocad Presico from Jensen, any info or knowledge will be appreciated .